Cabletron Systems ELS10-26TX manual Setting the Baud Rate

Page 83

Monitoring and Managing Your ELS10-26

3. Enter the new community name.

LCM prompts you to verify the new community name by retyping it.

4. Retype the new community name.

4.5.5 Setting the Baud Rate

You can set the baud rate for your LCM console connection. The options for baud rate include:

•1200

•2400

•4800

•9600

•19200

The default rate is 9600.

Note: Make sure that the baud rate you set matches the baud rate setting for the terminal you are using.

To display the current baud rate setting, at the LCM prompt:

1. Type baud

LCM responds:

Usage: baud [120024004800960019200]

Baud rate is 4800.

4-13

Image 83

Contents ELS10-26 User Guide Page FCC Notice DOC Notice Cabletron Software Program License Declaration of Conformity Contents Monitoring and Managing Your ELS10-26 ContentsAppendix B Glossary ELS10-26 Diagnostics and TroubleshootingAppendix a Technical Specifications Contents Viii Chapter Introduction About this Manual BBS Getting HelpDocument Conventions Related Documentation ELS10-26TX Front Panel OverviewSmartSTACK 10 ELS10-26 Architecture OSI Reference Model Store and Forward SwitchingDiscarding Local Trafﬁc Typical Switching ApplicationSmartSTACK 10 ELS10-26 Bridge Address Table Spanning Tree AlgorithmIntroduction SmartSTACK 10 ELS10-26 Sample Applications SmartSTACK 10 ELS10-26 Port MonitoringPacket Capturing and Monitoring SmartSTACK 10 ELS10-26 Trunking with 10 Mbps Ports SmartSTACK 10 ELS10-26 TrunkingSmartSTACK 10 ELS10-26 Backbone Conﬁguration SmartSTACK 10 ELS10-26 Fast EthernetSmartSTACK 10 ELS10-26 Trunking with 100 Mbps Ports Virtual Workgroups Trafﬁc Workgroup a Workgroup B Local Console Manager Command Syntax Conventions Help Basic LCM CommandsELS10-26 Local Console Manager Traplog EraseExit or Logout ELS10-26 Front Panel Chapter Unpacking and Installing Your ELS10-26Reset Switch Status LEDs ACT Describes the ELS10-26 buttons Installing AN FepimInstalling an Fepim Rack-mounting an ELS10-26 Installing the ELS10-26Attaching Rackmount Brackets Checking the POWER-UP Diagnostics Sequence Connecting to the Network Connecting the Local Console Manager10BASE-T/ 100BASE-TX Connecting UTP CablesCable Pinouts RJ45 Crossover Cable Connecting a UTP Segment to the FE-100TXFE-100TX Crossover Switch Fiber Optic Network Connection Connecting a Multimode Segment to the FE-100FXFE-100FX Port Unpacking and Installing Your ELS10-26 Unpacking and Installing Your ELS10-26 Spectrum Spel Spma Chapter Configuring Your ELS10-26Assigning IP Addresses Type ipaddr PORT-NUMBER IP Address Changing a Subnet Mask Displaying IP AddressesDeleting an IP Address To change the subnet mask, at the LCM prompt Enabling BridgingDisplaying Bridging Functions Disabling BridgingEnabling Trunking Trunk Connections Trunk GroupsTrunk Groups Disabling Trunking Display could look like the following Displaying Trunking StatusEnabled, Rip listening Enabling Port Monitoring Displaying Monitoring Status Disabling MonitoringEnabled, Rip listening Deﬁning Virtual Workgroups Defining and Deleting WorkgroupsLCM responds with the following display Assigning a Community Name Configuring BROADCAST/MULTICAST Storm Protection System Contact Modifying MIB VariablesCommunity Names System NameSystem Location Aging Parameter Set Community NameELS10-26 Statistics Chapter Monitoring and Managing Your ELS10-26ELS10-26 Management Tools System Statistics Gathering StatisticsEthernet Port Statistics Displaying Status Using LCM to Check ELS10-26 StatusEnabled, Rip listening Displaying MAC Addresses To display all MAC addresses, at the LCM prompt LCM would display Displaying Manufacturing InformationManaging the ELS10-26 Using LCM to Manage the ELS10-26 Enabling a Port Disabling a PortNoRIP Option Changing a Community Name Setting the Baud Rate Setting a Reboot Time Power-up LED Sequence Chapter ELS10-26 Diagnostics and TroubleshootingPOWER-UP Diagnostics Software Checksum Comparison Speciﬁc Power-up TestsStatus and Activity Indicators Power-up Diagnostics ResultsResponses to Failures AT POWER-UP ELS10-26 Front Panel LEDs LED Connectivity Problems TroubleshootingELS10-26 does not Power UP 3 ELS10-26 Does Not Respond to NMS 2 ELS10-26 Has RebootedELS10-26 Diagnostics and Troubleshooting Electrical Appendix a Technical Specifications ELS10-26 SpecificationsConnector Ports PhysicalStandard Support Diagnostic LEDsEnvironmental Serial Cable PIN Assignments Address Table SizeManagement Support Regulatory Compliance10BASE-T PIN Assignments ConnectorsPin Assignment a STRAIGHT-THROUGH Wiring5 4 3 Rule Crossover WiringFE-100FX Fepim SpecificationsFE-100TX Cable Type Worst Case Budget Typical Budget Agent AlarmAddress Address tableBps bits per second BackboneBandwidth Bpdu bridge protocol data unitData rate or speed CongestionData link layer DatagramEntity Full wire speedEncapsulation EncodeInitialization Intelligent bridge/switchIcmp Internet control message protocol IeeeISO International Standards Organization InternetworkingInteroperability IP Internet protocolMIB management information base MAC media access controlMask Mbps megabits per secondPacket Power budgetPropagation delay OSI Open Systems InterconnectionProtocol suite Rarp reverse address resolution protocolService ProtocolTranslating bridge SwitchSymbol Synchronous transmissionWAN wide area network UpstreamGlossary Numerics IndexIndex RIP Wiring crossover A-6 Straight-through A-5