Extron electronic MAV Creating a configuration, Example 1 Creating a set of video and audio ties

Page 29

The current configuration and all presets are saved in non-volatile memory. When power is applied, the last current configuration is retrieved. The previous presets remain intact.

If an error occurs during the self-test, the switcher locks up and will not operate. If your switcher locks up on power-up, call the Extron S3 Sales & Technical Support Hotline.

Creating a configuration

The current configuration can be changed using the front panel buttons. To change the current configuration, do the following:

1.

Press the Esc button to clear any input LEDs, output LEDs, or control LEDs

 

that may be on.

2.Select to configure video, audio, or both by pressing the Video and/or Audio buttons.

3.Select the desired input and output(s) by pressing the input and output buttons.

4.

Press and release the Enter button.

5.

Repeat steps 1 through 4 to create additional ties until the desired

 

configuration is complete.

1. Only one video input and one audio input can be tied to an output.

2.If a tie is made between an input and an output, and the selected output was previously tied to another input, the older tie is broken in favor of the newer tie.

3.To indicate current ties, output LEDs light when an input is selected. To clear unwanted outputs, press and release the associated output buttons.

4.If, when you configure video and audio ties, the Audio LED blinks and the Video LED is on after you select an input or output, the LEDs indicate audio breakaway: the audio ties are not the same as the video ties for that input.

5.If an input with no tie is selected, only that input’s LED lights.

6.When the Video and Audio LEDs are on, if an input with an audio tie but no video tie is selected, the input’s LED lights and the Audio LED blinks.

7.As each output is selected, the associated output LED blinks to indicate a tentative tie. LEDs for output(s) that were already tied to the input light steadily. Outputs that are already tied can be left on, along with new blinking selections, or toggled off by pressing the associated output button.

Example 1: Creating a set of video and audio ties

See figure 3-4 and the following steps for an example in which input 5 is tied to outputs 3, 4, and 8.

This example assumes that there are no ties in the current configuration.

APress and release the Esc button. The Esc LED flashes once.

BTo select video and audio for the tie, if necessary, press and release the Video and Audio buttons until the Video and Audio LEDs light.

CPress and release the input 5 button. The input 5 LED lights.

MAV Series Switchers • Operation

3-5

Image 29
Contents MAV Series Matrix SwitchersConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQS-1 Quick Start MAV Series SwitchersQuick Start MAV Series Switchers, cont’d Table of Contents Table of Contents, cont’d MAV Series Switchers Table of Contents Iii Iv MAV Series Switchers Table of Contents One Introductiontroduction, cont’d MAV Series Switchers IntroductionTypical MAV 1616 component matrix switcher application MAV Introduction, cont’dMAV 128 RCA model FeaturesAll models MAV 168/1616 video modelsMAV 168/1616 audio models MAV Series Switchers Introduction Introduction, cont’d Two Installation Overview Installationstallation, cont’dMounting the Switcher MAV Series Switchers InstallationMAV 1616 component video matrix switcher with audio Video input and output connections video models only Installation, cont’dPower connection Audio input connections Audio input and output connections audio models onlyExternal sync connection RS-232/422 connectionAdditional rear panel view MAV switcher11 MAV 168 composite video matrix switcher with audio Three MAV Series Switchers Operation Front Panel Controls and IndicatorsOperationeration, cont’d DefinitionsControls Control buttons and LEDsOperation, cont’d PowerFront Panel Operations Front panel I/O label windowsExample 1 Creating a set of video and audio ties Creating a configurationExample 2 Adding a tie to a set of video and audio ties Example 1 Creating a tieExample 3 Selecting audio and selecting input Example 3 Removing a tie from a set of video and audio tiesViewing a configuration Example 4 Viewing the current configuration Audio buttons 12 Example 5, step D Muting and unmuting outputs Example 5 Muting and unmuting an outputExample 7 Recalling a preset Using presetsExample 6 Saving a preset Viewing and adjusting the audio level models with audio LED Example 8 Viewing and adjusting an audio level16 +8dB displayed on MAV 128 RCA Executive mode front panel security lockout TroubleshootingSystem reset to factory defaults Plasma display S-video problemWorksheet example 1 System equipment WorksheetsWorksheet example 3 Test configuration Worksheet example 2 Daily configurationInput sources Output destinations Configuration worksheetOperation, cont’d Four Switcher-Initiated Messages Host-to-Switcher InstructionsMAV Series Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dUsing the Command/Response Table Switcher Error ResponsesProgrammer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d Executive mode Five Installing the software Matrix Switchers Control ProgramUsing the software MatrixSoftware,cont’dWindows buttons Extron Matrix Switchers Control Program window blankWindows menus Matrix Software, cont’dButton-Label Generator Using emulation modeUsing the help system Extron’s Button-Label Generator window AAppendix a MAV Series Switchers Specifications Specificationsecifications, cont’dSync MAV Series Switchers Specifications A-3Control/remote switcher Specifications, cont’dOptional accessories MAV switcher part numbersPart Numbers CablesExtron Part BNC-4 Mini HR Cable Assorted connectors BNC connectorsBNC-5 Mini HR Cable Plenum BNC-5 Mini HR CableAppendixBB ReferenceInformation,co t’d Hardware ProceduresOpening the switcher Swapping the serial ports Closing the switcherMAV Series Switchers Reference Information Reference Information, cont’d Installing a firmware updateReplacing the AC fuse Button LabelsReference Information, cont’d MAV Series Switchers Reference Information Reference Information, cont’d Extron’s Warranty Extron Electronics, USA
Related manuals
Manual 21 pages 49.15 Kb

MAV specifications

Extron electronics are renowned for their cutting-edge technology in the realm of AV systems and distribution solutions. Among its notable products, the MAV series stands out as an advanced tool for managing audio/video signals across various applications. The Extron MAV, or Multi-Format Audio/Video Switcher, provides a seamless approach to switching between multiple sources effortlessly, making it an integral component in modern AV setups.

One of the main features of the Extron MAV is its multi-format switching capability. It supports a wide variety of video signals, including HDMI, VGA, display port, and composite video, allowing users to connect different devices without worrying about compatibility issues. This versatility is particularly beneficial in environments such as classrooms, conference rooms, and auditoriums, where multiple input sources like laptops, projectors, and other multimedia devices are commonly used.

Another significant characteristic of the MAV series is its robust audio integration. The MAV not only switches video signals but also routes audio through its built-in audio switcher. This feature simplifies the workflow by allowing users to manage audio from the same interface, ensuring synchronized audio and video output. The device also supports advanced audio features, including audio de-embedding and analog audio outputs, making it suitable for complex AV systems.

The MAV employs Extron's proprietary technologies to enhance signal integrity. For instance, it adopts advanced signal processing to prevent degradation of video quality, maintaining a clear and crisp image even over long distances. The incorporation of automatic switching allows for a quick transition when the active source changes, ensuring minimal downtime during presentations.

The intuitive user interface of the MAV is another defining characteristic. It can be controlled through a dedicated touchscreen or via a web-based interface, providing flexibility in how users interact with the system. Additionally, the MAV can be integrated with control systems like Extron’s Global Scripter, enabling customized automation and enhanced interactivity.

In summary, the Extron MAV exemplifies advanced AV technology with its multi-format switching, integrated audio management, superior signal processing, and user-friendly interface. Its adaptability and robust performance make it an essential tool for professional AV environments, catering to a broad range of applications and ensuring a seamless experience for users and audiences alike. Whether in educational settings, corporate environments, or entertainment venues, the Extron MAV consistently delivers high-quality audio and video performance.