IN1508 – Setup Guide
N For full installation, configuration, and operation details, refer to the
IN1508 User’s Manual, available at www.extron.com.
This guide provides quick start instructions for an experienced installer to set up and operate the Extron IN1508 Scaling Presentation Switcher.
Installation and cabling
| 1 | 3 |
|
|
|
|
| 6 |
|
|
|
|
|
|
|
|
|
|
| OUTPUT |
|
| |||
|
| I | YC |
|
|
|
|
|
| LISTED | OUTPUT |
|
| AUDIO INPUT |
|
|
|
|
| ||||||
|
| VID |
|
|
|
|
|
|
| C | US 1T23 |
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
| I.T.E. |
| 1 | 2 | 3 | 4 | 5 | 6 |
|
| A |
|
| |
|
| N |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
| RGB |
|
|
|
| RGB | L |
|
|
|
|
|
| L |
|
|
| |
|
| P |
|
|
|
|
|
|
|
|
|
| Y, |
|
|
|
|
|
|
|
|
|
| ||
|
| VID |
| YC |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| B |
| ||
|
| U |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 7 | 8 |
| L | R |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| R |
|
|
|
|
|
| R |
|
|
| |
50/60Hz | T | 2 | 4 | Y | 5 | RGB | 7 | DVI | 8 |
|
|
|
|
|
|
|
|
|
|
|
|
| |||
1 |
|
| 2 | 3 |
|
| 4 |
|
| 5 |
| 6 |
| 7 |
|
| 8 |
|
| 9 |
| 10 | 11 | 12 | |
Connections
aAC power connector | gOutput |
bInputs 1 and 2 composite video BNC connectors | hAudio Inputs 1 through 5 RCA connectors |
cInputs 3 and 4 | iAudio Inputs 6 through 8 3.5 mm mini stereo jacks |
dInput 5 component video BNC connectors | jAudio Output A RCA connectors |
eInputs 6 and 7 RGB video | kAudio Output B captive screw connector |
fInput 8 DVI video connector |
Step 1 — Mounting
Turn off or disconnect all equipment power sources. For tabletop use, affix the rubber feet. For optional rack mounting, secure the supplied brackets (see image at right) and mount in a rack.
Step 2 — Video inputs and output
a. Inputs 1 and 2 — Connect composite video sources to these female BNC connectors.
b. Inputs 3 and 4 — Connect
c. Input 5 — Connect a component video (YUVi, YUVp, HDTV) source to these female BNC connectors.
I
N P U T
Y
1 | VID | 3 | YC |
| VID |
| YC |
2 |
| 4 |
|
| 5 | ||
|
|
|
I N P U T
1
2
VID
VID
3
4
YC
5
B RG
B RG
6
7
DVI
OUTPUT Y, 
T
INPU 4
AUDIO3
2
L
R 
| OUTPUTA |
| B |
| L |
6 |
|
5 | R |
8 | |
7 |
|
d. Inputs 6 and 7 — Connect RGB video sources to these
e. Input 8 — Connect a single link of
f. Output — Connect an RGB or component video display to this
Step 3 — Audio inputs and outputs
a. Audio Inputs 1 through 5 RCA connectors — Connect stereo or mono audio sources.
| 6 |
|
|
RGB |
|
|
|
RGB | 7 | DVI | 8 |
|
|
OUTPUT |
|
| AUDIO INPUT |
|
|
| OUTPUT | |
| 1 | 2 | 3 | 4 | 5 | 6 |
| A |
RGB | L |
|
|
|
|
|
| L |
Y, |
|
|
|
|
|
|
|
|
|
|
|
|
|
| 7 | 8 | B |
|
|
|
|
|
| L R | ||
| R |
|
|
|
|
|
| R |
b. Audio Inputs 6 through 8 3.5 mm mini jacks — Connect computer audio sources.
c. Output A RCA audio connectors — Connect a stereo or mono audio device (receiver, amplifier, or the like).
— OR —
Output B audio captive screw connector — Connect a stereo or mono audio device (receiver, amplifier, or the like); wire the connector as shown at right.
Tip | L | Tip | L | |
Ring | NO GROUND HERE. | |||
|
| |||
|
| Sleeve(s) |
| |
Tip | R | Tip | R | |
Ring | NO GROUND HERE. | |||
|
|
Balanced Stereo Output | Unbalanced Stereo Output |
CAUTION For unbalanced audio output, connect the sleeve(s) to the ground contact. DO NOT connect the sleeve(s) to the negative
Rev. A 04 10