Extron electronic IN1508 Front Panel and Remote Control Controls and Indicators, Setup, RS-232

VGA 1024x852 UXGA

SVGA 1024x1024 720p

XGA 1366x768 1080i

SXGA 1365x1024 1080p

6

Input buttons and LEDs —

IN1508

IN1508 — Setup Guide (cont'd)

Step 4 — RS-232	RS-232
a. RS-232—Connect a control system or

computer to the rear panel RS-232 port.

The IN1508 User's Manual, at www.extron.com details Simple Instruction Set (SIS™) commands.

Step 5 — Power

AC power connector — Plug in a standard IEC power cord from a 100 to 240 VAC, 50-60 Hz power source into this receptacle. Turn on the input and output devices after you power up the switcher.

100-240V 50-60Hz

50/60Hz

Front Panel and Remote Control Controls and Indicators

Many of the switcher’s functions are available via simple controls on the front panel. Front panel LEDs provide indications of some of the basic system functions. For more complex tasks, such as system configuration, the switcher has a menu system that is operated by using the front panel buttons. The menu system reports via an on-screen display on the connected output device.

a
	Press to select an input to scale and	IR	INPUT	OUTPUT RATE	PIP	PICTURE CONTROLS		SCALING PRESENTATION SWITCHER
			2 3 4 5 6 7 8			CONT/	COL/
		1		ON	SWAP	CENTER SIZE BRT	TNT MENU	ENTER

output. The lit Input LED indicates the selected input.

bOutput Rate button and LEDs — Press to cycle through 12 common resolutions at the 60 Hz refresh rate.

1 2 3 4 5

The LEDs indicate the selected resolution.

NSome rates cannot be selected using this button. Use the menu system for additional rates.

cPIP On (picture-in-picture) button and LED — Press to toggle the PIP feature on and off. The LED lights when PIP mode is on.

d e f

PIP Swap button — Press when the PIP feature is on to swap the main and PIP images.

Picture Control buttons — Press to change the centering, size, contrast, brightness, color, or tint.

Menu control buttons

Menu button — Press to activate the on-screen display menu system (shown below) or to back up one level from the currently selected menu or submenu.

, , , and buttons — Press to move the highlight bar over submenus or selections and to adjust selected settings. Enter button — Press to select a highlighted submenu or selection.

Menu system operation

At right is a a flowchart of the submenus in the main menu system. Each submenu leads to a series of submenus or to a “slider” type status indicator for individual settings.

No menu display

Menu Menu Timeout

EXTRON ELECTRONICS IN1508 SCALING PRESENTATION SWITCHER

Setup

Use the front panel menu controls and the connected display's on-screen display to set up the IN1508 using the following procedures.

NIf no image can be seen on the display, use the front panel Output Rate button to select 1024x768 or 720p.

You can toggle between an RGBHV and high definition component video output by pressing and holding the PIP On button while you cycle the IN1508 power.

Set output signal settings

INPUT

PICTURE

OUTPUT

AUDIO

ADVANCED

Enter

Enter

Select

Enter

Enter

Enter

Center	Zoom	Aspect
Size	Pan	Advanced

Brightness	+64
Contrast	+45
Color	+64

Tint +64

Sharpness +64

Resolution	Sync Polarity
Refresh Rate	Signal Type
Output Volume	Audio Delay
Input Gain/Atten
Freeze	Swap	Fade Switch
Blank	PIP Mode	Blue Mode

Input 5

Test Pattern

Reset

1.	Navigate to the Output submenu selection boxes.
2.	Press and to select among the Resolution, Refresh Rate, Signal Polarity, and Signal Type selection boxes.
3.	For each selection box, press and to select the settings that match the display's native settings.

NSome resolutions such as 1920x1200 and 1080p Sharp are only available via SIS command; refer to the IN1508 User’s Manual, available at www.extron.com, for the associated commands.

2IN1508 • Setup Guide