Extron electronic PVS 200 Mark screen location, 1a Mark the screen location, 2c Install the PMP

Page 15

1.Mark screen location

a. Mark the center line and the outer edges of screen.

T When marking the location of screens, devices, or site for installing transmitters and MediaLink control devices, use painters’ tape to avoid wall surface damage.

1a Mark the screen location

When marking the center line of the screen,

where possible, keep it aligned with the center of the ceiling tile. This makes the projector installation and alignment easier.

b.Mark any structural studs, utility pipes, conduits, or fire-breaks before drilling the hardware holes. Do not drill the holes at this time.

 

 

2. Install projector to verify location

PCM

a.Remove the ceiling tiles, and mark the maximum and

minimum throw distances on the T-frame.

Minimum/Maximum

b. Place the PCM 240 over the T-frame, between the two

Throw Distance Marks

 

marks. Lightly tighten the frame screws.

 

2b Place the PCM 240 on the T-bar

c.Back out the set screws on the PCM 240 adapter plate and screw the PMP into the pipe adapter, with the cable access hole closest to the ceiling. Turn it so the cable access hole faces away from the screen.

Tighten the set screws.

d.Back out the set screws on the top portion (the adjuster plate, see Abelow) of the UPB 25, and screw the plate onto the base of the PMP. Align it so the security flange is at the rear. Tighten the set screw.

PMP installed onto PCM 240

2c Install the PMP

a

Adjuster Plate

Set Screws (2)

Loosen the four Adjuster Plate

Locking Screws and slide the

Adjuster Plate away from the

Projector Bracket

b

Projector

Bracket

Adjuster Plate

Locking Screws (4)

2d Screw the adjuster plate onto the PMP

PoleVault Systems Installation • Installation — Stage 1

2-3

Page 14 Page 16
Image 15
Page 14 Page 16
Contents PoleVault Systems Sicherheitsanleitungen Deutsch PrecautionsSafety Instructions English Consignes de Sécurité FrançaisPoleVault Systems Installation Introduction IntroductionFCC Class a Notice Introduction, contd PoleVault System installation and wiring overviewRoom Typical classroom installationPoleVault Systems Installation Introduction Planning Room layoutADA overhead and side clearance requirements Example classroom installationIntroduction Planning, cont’d Location of the screen and projectorExample classroom with four speaker installation Location of MediaLink Controller and Wall PlatesType and location of the speakers Introduction Inventory Overview InventoryIncluded items PoleVault System Devices and Hardware, cont’d PoleVault System Devices and Hardware, contdPoleVault System Ceiling Speakers Introduction Inventory Overview, cont’dItems not included Optional installation hardwareInstallation tools Installation Overview Outline of installation stepsPoleVault Systems Installation Installation Overview PMP Projector Mounting Pole Where it goes Screws up into PCMPoleVault Systems Installation Installation Stage PCM 240 Projector Ceiling Mount1a Mark the screen location 2c Install the PMP2d Screw the adjuster plate onto the PMP Mark screen locationHorizontal offset Installation Stage One, cont’dWhen satisfied lock down the plate locking nuts Verify the image location5d Screw the PMP into the mounting plate viewed from below InstallationUsing these dimensions, mark and cut a hole for Cut the ceiling tileSecure the Projector Ceiling Mount to the ceiling Tighten the four T-bar securing screws on the PCM6e Tighten the turnbuckles Center holes on either side of the plate. Ensure Install the Screen6i Attach the safety cable to the PCM Power outlet installation on PCMStage Two Install the Wall Plates and MLC 104 IP This stage involves installing the devices shown belowMLC 104 IP Plus MediaLink Controller Cables PVS 204SA switcherMLC 104 IP Plus mud ring Stage Two Install the Wallplates and MLC 104 IP PlusInstall mud rings 1d Features for mud ring installation2c Pull the cables at each location Signal Cable Label colorPull cables Projector communication cables fromInstall wall plates Installation Stage Two, cont’dInstall MediaLink Controller TWire stripping lengths4a Connecting the MLC to the switcher Appropriate 4c Connect to the LAN using a CAT 5 cableConnect the MLC to the projector with An RS-232 cable or IR emitter cable, as4e Secure the MLC 104 IP Plus to the mud ring Connections made to the MLC 104 IP PlusPV SI 3C LP Ceiling Speakers Stage Three Install the PV SI 3C LP Ceiling SpeakersCut ceiling tile Cable the speakers Installation Stage Three, cont’d4c Wire the captive screw connector Dual mono output Stereo or Dual Mono output using parallel speaker wiringStereo output 5a Apply putty to speaker grill Finish speaker installationPMK 450 Pole Mount Kit Stage Four Install the PMK 450 and the PVS 204SAThis stage covers installing the devices shown below PVS 204SA PoleVault SwitcherPull the cables Installation Stage Four, cont’dInstall the PMK 450 Pole Mount kit Switcher and projector cable overview3d Set the DIP switches as desired Install the PVS 204SA switcherPMK 450 bottom plate and secure it using velcro 3c Wire the captive screw connector for the power supplyPVS 204SA cable connections Finish installing the Pole Mount kitBControl/power cable from the MLC 104 IP Plus Connect the cables to the switcher4c Attach and screw down rear plate 4d Replace projector on the adjuster plateLaunch GC2. Click on Help, then Contents or press F1 Stage Five Configure the SystemConfigure the system 1a Load Global Configurator 2 softwarePoleVault Systems Installation Installation Stage Test the system Installation Stage Five, cont’dLoosen all pivot screws and adjust the vertical angle 2c Check that an image is present, adjust as neededAdjust the configuration as necessary Final installationConnect sensor to the PPC 25 Optional Accessory Installation PPCConnect the PPC 25 to the switcher Connect sensor to paging speakerPoleVault Systems Installation Reference Information Installation Reference InformationInstallation Reference Information, cont’d Wall or furniture mountable with included Decora wall plateLbs 0.1 kg Projector Mount Pole PoleVault SwitcherProjector Drop Ceiling Mount Low Prole Multi-Product Pole Mount KitExtron Electronics. All rights reserved
Related manuals
Manual 50 pages 35.12 Kb

PVS 300, PVS 400, PVS 200 specifications

Extron Electronics is renowned for its innovative audiovisual solutions, and among its diverse range of products, the PVS (Presentation and Video System) series stands out. The PVS 400, PVS 300, and PVS 200 models are designed to streamline multimedia presentations while offering various features tailored to different user needs.

The Extron PVS 400 is the flagship model, ideal for sophisticated presentation environments. This powerful device supports 4K video distribution and includes multiple input capabilities including HDMI, VGA, and composite video. A significant feature of the PVS 400 is its ability to scale video inputs to fit various resolutions, ensuring optimal quality performance during presentations. The built-in streaming technology allows real-time video feeds to remote audiences, making it an excellent choice for hybrid and online meetings.

Built with advanced processing capabilities, the PVS 400 supports audio embedding and de-embedding, ensuring high-quality sound is delivered alongside the video. Additionally, the intuitive user interface simplifies operation, making it accessible for presenters at all levels. The system is designed for integration with Extron's global control platform, allowing seamless control of AV functions through a single touch panel.

The Extron PVS 300 serves as a mid-range solution offering robust features without compromising quality. It supports up to 1080p resolution, making it suitable for most conventional presentation environments. The PVS 300 incorporates essential features like audio mixing, simple video switching, and basic scaling capabilities. It's particularly well-suited for educational institutions and small to mid-sized conference rooms where high performance is necessary but extensive features are not required.

Lastly, the Extron PVS 200 is tailored for users needing a straightforward and cost-effective presentation tool. Designed for small meetings and classrooms, this model includes essential input options, basic video switching, and audio support. The PVS 200 is easy to set up and use, making it a popular choice for users seeking reliability without complex configurations.

In conclusion, the Extron PVS 400, PVS 300, and PVS 200 models represent a versatile range of solutions catering to various audiovisual needs. Whether it's the high-powered capabilities of the PVS 400, the balanced features of the PVS 300, or the budget-friendly nature of the PVS 200, Extron has positioned itself as a leader in the presentation technology market. Each model provides distinct characteristics that ensure effective communication and impactful presentations, contributing to the overall success of any meeting or event.
Top Page Image Contents