Extron electronic PVS 300, PVS 200, PVS 400 manual Cut ceiling tile

Page 29

NThe installation must conform to national and local electrical codes, and UL requirements. Refer to the device’s user manual for details.

1.Cut ceiling tile

If installing PV SI 3C LP speakers, do the following:

a.Remove the ceiling tiles where the speakers are to be installed.

TFor ease of working on the speaker when it is replaced on the T-bar, remove an adjacent tile(s).

b.Locate the tile center, and using the supplied template, trace and cut the hole for the speaker.

TPlace an empty box under the tile for support and to collect the waste.

Measure and mark the center point of the tile and align

1b Mark the tile and cut the hole

the cross marks with those on the supplied template.

 

Use a fine hacksaw blade to cut the tile without damaging the face.

a.Lay two supplied speaker V-rails across the tile on either side of the hole.

b.Remove the C-ring from the speakers and attach it to the center of the V-rails with the supplied hardware.

TAt the ends of each V-rail, bend the tabs upwards. This makes it easier when replacing the tile back on the T-bars. When installation is complete, bend the V-tabs

down onto the T-bars

2a Place the V-rails on either side of the

 

 

hole, insert and 2b attach the C-ring

c.Remove the plenum cover from the speaker terminals

d.Insert the speaker into the ceiling tile from the face side.

Bend Tabs

Upwards

Bend the end tabs upwards.

Loosen the screws and remove the plenum cover.

2c Remove plenum cover

PoleVault Systems Installation • Installation — Stage 3

2-17

Page 28 Page 30
Image 29
Page 28 Page 30
Contents PoleVault Systems Safety Instructions English PrecautionsConsignes de Sécurité Français Sicherheitsanleitungen DeutschFCC Class a Notice PoleVault Systems Installation IntroductionIntroduction Introduction, contd PoleVault System installation and wiring overviewPoleVault Systems Installation Introduction Planning Typical classroom installationRoom layout RoomIntroduction Planning, cont’d Example classroom installationLocation of the screen and projector ADA overhead and side clearance requirementsType and location of the speakers Example classroom with four speaker installationLocation of MediaLink Controller and Wall Plates Included items Introduction Inventory OverviewInventory PoleVault System Devices and Hardware, cont’d PoleVault System Devices and Hardware, contdPoleVault System Ceiling Speakers Introduction Inventory Overview, cont’dItems not included Optional installation hardwareInstallation tools PoleVault Systems Installation Installation Overview Installation OverviewOutline of installation steps PoleVault Systems Installation Installation Stage Where it goes Screws up into PCMPCM 240 Projector Ceiling Mount PMP Projector Mounting Pole2d Screw the adjuster plate onto the PMP 2c Install the PMPMark screen location 1a Mark the screen locationWhen satisfied lock down the plate locking nuts Installation Stage One, cont’dVerify the image location Horizontal offsetUsing these dimensions, mark and cut a hole for InstallationCut the ceiling tile 5d Screw the PMP into the mounting plate viewed from below6e Tighten the turnbuckles Secure the Projector Ceiling Mount to the ceilingTighten the four T-bar securing screws on the PCM 6i Attach the safety cable to the PCM Install the ScreenPower outlet installation on PCM Center holes on either side of the plate. EnsureMLC 104 IP Plus MediaLink Controller Stage Two Install the Wall Plates and MLC 104 IPThis stage involves installing the devices shown below Cables PVS 204SA switcherInstall mud rings Stage Two Install the Wallplates and MLC 104 IP Plus1d Features for mud ring installation MLC 104 IP Plus mud ringPull cables Signal Cable Label colorProjector communication cables from 2c Pull the cables at each locationInstall wall plates Installation Stage Two, cont’d4a Connecting the MLC to the switcher Install MediaLink ControllerTWire stripping lengths Connect the MLC to the projector with 4c Connect to the LAN using a CAT 5 cableAn RS-232 cable or IR emitter cable, as Appropriate4e Secure the MLC 104 IP Plus to the mud ring Connections made to the MLC 104 IP PlusPV SI 3C LP Ceiling Speakers Stage Three Install the PV SI 3C LP Ceiling SpeakersCut ceiling tile Cable the speakers Installation Stage Three, cont’dStereo output 4c Wire the captive screw connector Dual mono outputStereo or Dual Mono output using parallel speaker wiring 5a Apply putty to speaker grill Finish speaker installationThis stage covers installing the devices shown below Stage Four Install the PMK 450 and the PVS 204SAPVS 204SA PoleVault Switcher PMK 450 Pole Mount KitInstall the PMK 450 Pole Mount kit Installation Stage Four, cont’dSwitcher and projector cable overview Pull the cablesPMK 450 bottom plate and secure it using velcro Install the PVS 204SA switcher3c Wire the captive screw connector for the power supply 3d Set the DIP switches as desiredBControl/power cable from the MLC 104 IP Plus Finish installing the Pole Mount kitConnect the cables to the switcher PVS 204SA cable connections4c Attach and screw down rear plate 4d Replace projector on the adjuster plateConfigure the system Stage Five Configure the System1a Load Global Configurator 2 software Launch GC2. Click on Help, then Contents or press F1PoleVault Systems Installation Installation Stage Loosen all pivot screws and adjust the vertical angle Installation Stage Five, cont’d2c Check that an image is present, adjust as needed Test the systemAdjust the configuration as necessary Final installationConnect the PPC 25 to the switcher Optional Accessory Installation PPCConnect sensor to paging speaker Connect sensor to the PPC 25PoleVault Systems Installation Reference Information Installation Reference InformationLbs 0.1 kg Installation Reference Information, cont’dWall or furniture mountable with included Decora wall plate Projector Drop Ceiling Mount PoleVault SwitcherLow Prole Multi-Product Pole Mount Kit Projector Mount PoleExtron Electronics. All rights reserved
Related manuals
Manual 50 pages 35.12 Kb

PVS 300, PVS 400, PVS 200 specifications

Extron Electronics is renowned for its innovative audiovisual solutions, and among its diverse range of products, the PVS (Presentation and Video System) series stands out. The PVS 400, PVS 300, and PVS 200 models are designed to streamline multimedia presentations while offering various features tailored to different user needs.

The Extron PVS 400 is the flagship model, ideal for sophisticated presentation environments. This powerful device supports 4K video distribution and includes multiple input capabilities including HDMI, VGA, and composite video. A significant feature of the PVS 400 is its ability to scale video inputs to fit various resolutions, ensuring optimal quality performance during presentations. The built-in streaming technology allows real-time video feeds to remote audiences, making it an excellent choice for hybrid and online meetings.

Built with advanced processing capabilities, the PVS 400 supports audio embedding and de-embedding, ensuring high-quality sound is delivered alongside the video. Additionally, the intuitive user interface simplifies operation, making it accessible for presenters at all levels. The system is designed for integration with Extron's global control platform, allowing seamless control of AV functions through a single touch panel.

The Extron PVS 300 serves as a mid-range solution offering robust features without compromising quality. It supports up to 1080p resolution, making it suitable for most conventional presentation environments. The PVS 300 incorporates essential features like audio mixing, simple video switching, and basic scaling capabilities. It's particularly well-suited for educational institutions and small to mid-sized conference rooms where high performance is necessary but extensive features are not required.

Lastly, the Extron PVS 200 is tailored for users needing a straightforward and cost-effective presentation tool. Designed for small meetings and classrooms, this model includes essential input options, basic video switching, and audio support. The PVS 200 is easy to set up and use, making it a popular choice for users seeking reliability without complex configurations.

In conclusion, the Extron PVS 400, PVS 300, and PVS 200 models represent a versatile range of solutions catering to various audiovisual needs. Whether it's the high-powered capabilities of the PVS 400, the balanced features of the PVS 300, or the budget-friendly nature of the PVS 200, Extron has positioned itself as a leader in the presentation technology market. Each model provides distinct characteristics that ensure effective communication and impactful presentations, contributing to the overall success of any meeting or event.
Top Page Image Contents