Extron electronic PVS 200 Optional Accessory Installation PPC, Connect sensor to paging speaker

Page 42

Optional Accessory Installation — PPC 25

The example below is the installation of the optional accessory Priority Page Controller and Sensor (PPC 25).

The Priority Page Controller momentarily silences classroom audio whenever a page is made from a public address (PA) system.

For detailed information, refer to the PPC 25 Installation Instructions, supplied with the device.

NFollow all local fire and safety code requirements for installation and anchoring.

1. Connect sensor to paging speaker

a. Open the top of the Priority Page Sensor.

b. Loop (only) one of the Paging speaker wire leads around

the top (open) part of the Sensor. Either speaker wire

will work. Leave the other speaker wire connected

directly to the Paging speaker. Polarity need not be

observed.

Open the Sensor

• For a 25 V or 70V system — wrap 5 to 8 loops.

• For a 4/8 ohm system — wrap 2 to 4 loops.

c. Close the top of the Priority Page Sensor.

From

PA system

Page

Sensor

Ceiling Mounted

To PriorityPaging Speaker

Page Controller

1a Open the sensor and 1b Loop wire around the sensor

2.Connect sensor to the PPC 25

a.Cut an 18" section from the unterminated end of the supplied blue sensor cable, for use in step 3.

b.Connect the bare wire end of the supplied blue sensor cable to the 2-pole captive screw connector on the Page Sensor. Polarity need not be observed.

c.Route the connector end of the sensor cable to the PPC 25 Controller and plug it into the Paging Sensor port.

3. Connect the PPC 25 to the switcher

a. Connect the 18" cable made in step 2a to the Relay Out port on the PPC 25 Controller and to the mute and

ground pins on the PVS 204SA Vol/Mute port. Polarity need not be observed.

b. Use the included power supply cable assembly (PN 27-576-01LF) to power the PPC 25 from the

PVS 204SA power supply. The PPC 25 must be mounted near the PVS 204SA and its power supply.

From Classroom

PV SI 3C LP

Ceiling

Paging System

Speakers

Page

Ceiling Mounted

Paging Speaker

Sensor

 

Extron

 

PVS 204SA

 

Twisted Pair

 

Switcher

Remote

 

Relay

Vol/Mute

Control

Output

 

Extron

 

AMPLIFIED OUTPUTS

 

PPC 25

 

 

 

 

4/8

Mute

Priority Page

 

 

Ohms

 

L

R

(center)

Controller

RS-232 MLC/IR

DC VOL

 

 

Tx Rx IR

12V

 

 

A B C

 

10V

Ground

 

 

(right)

 

 

 

VOL/MUTE

 

PVS 204SA

 

 

rear panel

 

3a Connect the relay to the switcher

2-30 PoleVault Systems Installation • Optional Accessory Installation

Image 42
Contents PoleVault Systems Consignes de Sécurité Français PrecautionsSafety Instructions English Sicherheitsanleitungen DeutschPoleVault Systems Installation Introduction IntroductionFCC Class a Notice PoleVault System installation and wiring overview Introduction, contdRoom layout Typical classroom installationPoleVault Systems Installation Introduction Planning RoomLocation of the screen and projector Example classroom installationIntroduction Planning, cont’d ADA overhead and side clearance requirementsExample classroom with four speaker installation Location of MediaLink Controller and Wall PlatesType and location of the speakers Introduction Inventory Overview InventoryIncluded items PoleVault System Devices and Hardware, contd PoleVault System Devices and Hardware, cont’dIntroduction Inventory Overview, cont’d PoleVault System Ceiling SpeakersOptional installation hardware Items not includedInstallation tools Installation Overview Outline of installation stepsPoleVault Systems Installation Installation Overview PCM 240 Projector Ceiling Mount Where it goes Screws up into PCMPoleVault Systems Installation Installation Stage PMP Projector Mounting PoleMark screen location 2c Install the PMP2d Screw the adjuster plate onto the PMP 1a Mark the screen locationVerify the image location Installation Stage One, cont’dWhen satisfied lock down the plate locking nuts Horizontal offsetCut the ceiling tile InstallationUsing these dimensions, mark and cut a hole for 5d Screw the PMP into the mounting plate viewed from belowSecure the Projector Ceiling Mount to the ceiling Tighten the four T-bar securing screws on the PCM6e Tighten the turnbuckles Power outlet installation on PCM Install the Screen6i Attach the safety cable to the PCM Center holes on either side of the plate. EnsureStage Two Install the Wall Plates and MLC 104 IP This stage involves installing the devices shown belowMLC 104 IP Plus MediaLink Controller PVS 204SA switcher Cables1d Features for mud ring installation Stage Two Install the Wallplates and MLC 104 IP PlusInstall mud rings MLC 104 IP Plus mud ringProjector communication cables from Signal Cable Label colorPull cables 2c Pull the cables at each locationInstallation Stage Two, cont’d Install wall platesInstall MediaLink Controller TWire stripping lengths4a Connecting the MLC to the switcher An RS-232 cable or IR emitter cable, as 4c Connect to the LAN using a CAT 5 cableConnect the MLC to the projector with AppropriateConnections made to the MLC 104 IP Plus 4e Secure the MLC 104 IP Plus to the mud ringStage Three Install the PV SI 3C LP Ceiling Speakers PV SI 3C LP Ceiling SpeakersCut ceiling tile Installation Stage Three, cont’d Cable the speakers4c Wire the captive screw connector Dual mono output Stereo or Dual Mono output using parallel speaker wiringStereo output Finish speaker installation 5a Apply putty to speaker grillPVS 204SA PoleVault Switcher Stage Four Install the PMK 450 and the PVS 204SAThis stage covers installing the devices shown below PMK 450 Pole Mount KitSwitcher and projector cable overview Installation Stage Four, cont’dInstall the PMK 450 Pole Mount kit Pull the cables3c Wire the captive screw connector for the power supply Install the PVS 204SA switcherPMK 450 bottom plate and secure it using velcro 3d Set the DIP switches as desiredConnect the cables to the switcher Finish installing the Pole Mount kitBControl/power cable from the MLC 104 IP Plus PVS 204SA cable connections4d Replace projector on the adjuster plate 4c Attach and screw down rear plate1a Load Global Configurator 2 software Stage Five Configure the SystemConfigure the system Launch GC2. Click on Help, then Contents or press F1PoleVault Systems Installation Installation Stage 2c Check that an image is present, adjust as needed Installation Stage Five, cont’dLoosen all pivot screws and adjust the vertical angle Test the systemFinal installation Adjust the configuration as necessaryConnect sensor to paging speaker Optional Accessory Installation PPCConnect the PPC 25 to the switcher Connect sensor to the PPC 25Installation Reference Information PoleVault Systems Installation Reference InformationInstallation Reference Information, cont’d Wall or furniture mountable with included Decora wall plateLbs 0.1 kg Low Prole Multi-Product Pole Mount Kit PoleVault SwitcherProjector Drop Ceiling Mount Projector Mount PoleExtron Electronics. All rights reserved
Related manuals
Manual 50 pages 35.12 Kb

PVS 300, PVS 400, PVS 200 specifications

Extron Electronics is renowned for its innovative audiovisual solutions, and among its diverse range of products, the PVS (Presentation and Video System) series stands out. The PVS 400, PVS 300, and PVS 200 models are designed to streamline multimedia presentations while offering various features tailored to different user needs.

The Extron PVS 400 is the flagship model, ideal for sophisticated presentation environments. This powerful device supports 4K video distribution and includes multiple input capabilities including HDMI, VGA, and composite video. A significant feature of the PVS 400 is its ability to scale video inputs to fit various resolutions, ensuring optimal quality performance during presentations. The built-in streaming technology allows real-time video feeds to remote audiences, making it an excellent choice for hybrid and online meetings.

Built with advanced processing capabilities, the PVS 400 supports audio embedding and de-embedding, ensuring high-quality sound is delivered alongside the video. Additionally, the intuitive user interface simplifies operation, making it accessible for presenters at all levels. The system is designed for integration with Extron's global control platform, allowing seamless control of AV functions through a single touch panel.

The Extron PVS 300 serves as a mid-range solution offering robust features without compromising quality. It supports up to 1080p resolution, making it suitable for most conventional presentation environments. The PVS 300 incorporates essential features like audio mixing, simple video switching, and basic scaling capabilities. It's particularly well-suited for educational institutions and small to mid-sized conference rooms where high performance is necessary but extensive features are not required.

Lastly, the Extron PVS 200 is tailored for users needing a straightforward and cost-effective presentation tool. Designed for small meetings and classrooms, this model includes essential input options, basic video switching, and audio support. The PVS 200 is easy to set up and use, making it a popular choice for users seeking reliability without complex configurations.

In conclusion, the Extron PVS 400, PVS 300, and PVS 200 models represent a versatile range of solutions catering to various audiovisual needs. Whether it's the high-powered capabilities of the PVS 400, the balanced features of the PVS 300, or the budget-friendly nature of the PVS 200, Extron has positioned itself as a leader in the presentation technology market. Each model provides distinct characteristics that ensure effective communication and impactful presentations, contributing to the overall success of any meeting or event.