Extron electronic MVX 128 manual Example 1 Creating a set of video and audio ties

Page 27

Example 1: Creating a set of video and audio ties

In the following example, input 5 is tied to outputs 3, 4, and 8. The steps show the front panel indications that result from your actions.

NThis example assumes that there are no ties in the current configuration.

1.

Press and release the Esc button (figure 3-3).

Press the Esc button to clear all selections.

CONTROL

1

ENTER PRESET VIEW ESC

1= Blink once The LED blinks once.

Figure 3-3 — Clear all selections

2. To select video and audio for the tie, if necessary, press and release the RGBHV button and the Audio button until the LEDs light (figure 3-4).

I/O

RGBHV AUDIO

Press the RGBHV button to toggle on and off.

The LED lights when selected.

Press the Audio button to toggle on and off.

The LED lights when selected.

Figure 3-4 — Select RGBHV and audio

3.

Press and release the input 5 button (figure 3-5).

Press and release the Input 5 button.

3 4 5

INPUTS 6

The LED lights.

Figure 3-5 — Select an input

MVX 128 A VGA Matrix Switchers • Operation 3-9

Image 27
Contents MVX 128 a VGA Matrix SwitcherSicherheitsanleitungen Deutsch PrecautionsSafety Instructions English Consignes de Sécurité FrançaisQuick Start MVX 128 a VGA Matrix Switchers Plug the switcher into a grounded AC sourceMVX 128 a VGA Matrix Switchers Quick Start QS-1 Create a tie Saving or recalling a presetViewing and adjusting the audio level QS-2 MVX 128 a VGA Matrix Switchers Quick StartTable of Contents Table of Contents, cont’d One About this Manual About the MVX 128 a Matrix SwitcherMVX 128 a VGA Matrix Switchers Introduction IntroductionDefinitions Introduction, cont’d FeaturesMVX 128 a VGA Matrix Switchers Introduction Introduction, cont’d Two Cabling and Rear Panel Views InstallationMounting the Switcher MVX 128 a VGA Matrix Switchers InstallationAudio connections Captive screw connector wiring for audio inputsRS-232/RS-422 connection Installation, cont’dPower connection Reset buttonInstallation, cont’d Three Definitions Front Panel Controls and IndicatorsMVX 128 a VGA Matrix Switchers Operation OperationSample label Input and output buttonsControl buttons Operation, cont’dSee Viewing and adjusting the input audio level on Controls Front Panel Operations PowerCreating a configuration Example 1 Creating a set of video and audio ties Press and release the Esc button figurePress and release the input 5 button figure Press and release the Enter button figure Select the outputsThis example assumes that you have performed example Example 2 Adding a tie to a set of video and audio ties13 Press the Enter button 15 Clear all selections Example 3 Removing a tie from a set of video and audio ties18 Deselect the output 21 Clear all selections Viewing a configuration22 Select Rgbhv or video and audio Rgbhv button and the Audio button figureVideo Audio Press and release the Rgbhv button to deselect Rgbhv figureExample 5 Muting and unmuting an output Muting and unmuting video and/or audio28 Select Rgbhv and audio 30 Unmute the outputs Example 6 Saving a preset Using global presetsPress and release the Output 1 button figure LED blinks figurePress and release the Preset button figure Example 7 Recalling a preset40 Press the Enter button Viewing and adjusting the input audio levelPress and release an input button DB when blinking slowly, 2 dBWhen blinking quickly, and 3 dB When lit. See the table at right42 Clear all selections Example 10 Viewing and adjusting an input audio levelView View ESC Outputs Press and release the Audio button figureViewing and adjusting the output volume Released or the upper or lower limit is reachedAudio mode. The Audio button stops blinking Audio output volume settings Reading the displayed volume47 Clear all selections Example 11 Viewing and adjusting an output volume level49 Select output Performing a system reset from the front panel Locking out the front panel Executive modeSelecting the RS-232/RS-422 protocol and baud rate Enter Preset View ESC Rgbhv AudioPerforming an absolute system reset from the rear panel Rear Panel OperationsNot occur within 1 second Optimizing the Audio Performing a hard reset from the rear panelTroubleshooting Configuration WorksheetsWorksheet example 1 System equipment Audio Worksheet example 2 Daily configuration61 Worksheet example 3 Test configuration Worksheet example 3 Test configurationConfiguration worksheet Output destinationsOperation, cont’d Four Programmer’s Guide Host-to-Switcher InstructionsSwitcher-Initiated Messages MVX 128 a VGA Matrix Switchers Programmer’s GuideUsing the Command/Response Tables Switcher Error ResponsesX1@ = Command/Response Table for SIS CommandsSymbol definitions X1 =Description Command Ascii command Response Additional% G InX! AudX$ Audio volume adjustment settings EX!NI EZG X1* CY Information requests X1X1X1X1X1X2Programmer’s Guide, cont’d Five Matrix Software Matrix Switchers Control ProgramInstalling the software MVX 128 a VGA Matrix Switchers Matrix SoftwareClick OK and proceed to step Using the softwareMatrix Software, cont’d Open file window Updating firmwareClick the Exit button to exit the firmware loader utility Windows buttons, drop boxes, and trashcan Windows menusFile menu Tools menu Audio-Output volume settings Displays the audioTies shown as lines Preferences menuButton-Label Generator Program Using emulation modeUsing the help system Master-Reset selectionAppendixAA Specifications Specifications, Part Numbers, AccessoriesAudio Specifications, Part Numbers, Accessories, cont’d Adapters, power supplies, labels Part number Part Numbers and AccessoriesAccessories Included parts Replacement part NumberCables Male-to-female VGA molded connector cables Part numberMale-to-female VGA backshell connector cables Part number Male-to-male VGA molded connector cables Part numberFigure A-1 Button label blanks, 12-button strips Button LabelsSpecifications, Part Numbers, Accessories, cont’d Extron Electronics, Europe FCC Class a Notice Extron’s WarrantyExtron Electronics, USA