Extron electronic MVX 88 Series manual Control buttons and LEDs, O and Audio Setup button

Page 22

PRELIMINARY

Operation, cont’d

Control buttons and LEDs

E Enter button — The Enter button saves changes when you set up a new configuration. To create a simple configuration:

 

• Specify video, audio, or both (see controls [G] and [H]).

 

• Press the desired input button (C).

 

• Press the desired output button(s) (D).

 

• Press the Enter button.

F

Preset button and LED — The Preset button activates either Save Preset mode

 

or Recall Preset mode. Save Preset mode saves a configuration as a preset.

 

Recall Preset mode recalls and activates a previously-defined preset. The

 

Preset button indicates Save Preset mode when it is blinking and Recall Preset

 

mode when it lights steadily.

 

Alternate reset function — This button is also used to clear all ties and

 

presets. See “Clearing all ties and presets” on page 3-24.

I/O selection and audio/video controls and indicators

G I/O and Audio Setup button —

•Press and release — Pressing the I/O button cycles through video and audio, video only, or audio only for input and output selection. See the Video and Audio LEDs (H) for the sequence.

•Press and hold — The I/O button also serves as the Audio Setup mode selection button. To enable the Audio Setup mode, press and hold the Audio Setup button for about 2 seconds until the Audio Setup LED (I) lights. In Audio Setup mode, you can view and/or change the current audio level setting for each input. See “Adjusting input audio gain and attenuation” on page 3-18.

Audio Setup mode times out after approximately 30 seconds of inactivity.

Alternate reset function — This button is also used to perform a system reset.

See “Resetting the system to factory defaults” on page 3-25.

H Video/+dB LED and Audio/–dB LED —

•I/O selection — The Video and Audio LEDs indicate whether video and audio, video only, or audio only will be selected using the input buttons (C) and output buttons (D).

Pressing the I/O button advances through a cycle of video and/or audio selections as shown on figure 3-2.

 

MVX SERIES

VID

+dB

VID

+dB

VID

+dB

VID

+dB

 

AUD

-dB

AUD

-dB

AUD

-dB

AUD

-dB

VGA/AUDIO MATRIX SWITCHER

 

I/O

 

Press

Press

 

Press

 

 

 

 

 

 

VID

+dB

 

 

 

 

 

 

 

 

AUD

-dB

Default

Video Only

Audio Only

Video & Audio

 

AUDIO SETUP

 

 

 

 

 

 

 

 

 

 

 

 

 

= ON

= OFF

 

 

 

 

Figure 3-2 — Video and/or audio selection cycle

•Audio Setup mode — The –dB and +dB LEDs indicate the polarity of the audio level setting. See “Adjusting input audio gain and attenuation” on page 3-18. Both LEDs light to indicate unity gain (0 dB).

3-4 MVX 44 / 48 / 84 / 88 VGA Matrix Switchers • Operation

Page 21 Page 23
Image 22
Page 21 Page 23
Contents VGA Matrix Switcher MVX 44 / 48 / 84 / 88 seriesSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolFCC Class a Notice Page Quick Start MVX Series VGA Matrix Switchers MVX 44 / 48 / 84 / 88 VGA Matrix Switchers Quick Start QS-1Viewing and adjusting the audio input gain Powering upSaving or recalling a preset QS-2 MVX 44 / 48 / 84 / 88 VGA Matrix Switchers Quick StartTable of Contents Table of Contents, cont’d One About the Switchers MVX 44 / 48 / 84 / 88 VGA Matrix Switchers IntroductionFeatures Any input to any or all outputsIntroduction, cont’d Two Rack mounting the switcher Mounting the SwitcherTabletop use Furniture mounting the switcher Mounting the switcherCabling and Rear Panel Views Video and audio input connectionsStrap the audio cable to the extended tail of the connector RGB video output connectors Connect Rgbhv videoVideo and audio output connections Control of the switcher Power connectionRemote connection Three MVX 44 / 48 / 84 / 88 VGA Matrix Switchers Operation Front Panel Controls and IndicatorsDefinitions Input and output selection controls and indicators Infrared sensor and Power/audio/data LEDPower/data/audio LED Control buttons and LEDs Selection and audio/video controls and indicatorsO and Audio Setup button Video/+dB LED and Audio/-dB LEDButton is released or the lower limit is reached Ignores the commandAttenuation on Has reached the maximum attenuation -18 dBOperations Powering up the switcherCreating a set of ties Select video and audio for the tie figure Example 1 Create a set of video and audio tiesPress and release the Input 5 button figure Current configuration -7 is now Press and release the Enter button figurePress and release the Output 1 button figure Example 2 Add a video tie to a set of video and audio tiesSelect video only for the tie figure Press and release the Enter button figureExample 3 Remove a tie from a set of ties Current configuration -12 is nowSelect audio only for the tie figure Press and release the Output 4 button figure 15 Deselect the outputExample 4 View ties by selecting an input Viewing the configurationSelect both video and audio for viewing figure Press and release the I/O button figure Press and release the I/O button figureExample 5 View ties by selecting outputs Press and release the Output 3 button figure24 Deselect audio to view video ties only Using presets Example 6 Save a presetExample 7 Recall a preset Preset 2 PresetAdjusting input audio gain and attenuation Press and release the Input 1 button figurePreliminary Example 8 Adjust the input audio gain = unlit, = blinking LEDOutput 1 LED + 2 presses +2 dBExample 9 Resetting audio gain single input SavedExample 10 Resetting audio gain all inputs Setting the output audio levelPress and release the and buttons simultaneously figure Front panel security lockout Executive mode Clearing all ties and presetsResetting the system to factory defaults MemoryTroubleshooting Optimizing the AudioMain WorksheetsWorksheet example 1 System equipment VTGWorksheet example 2 Daily configuration Classical music from the CD player input 5 isWorksheet example 3 Test configuration 45 Worksheet example 3 Test configurationPreliminary Configuration worksheet Input sources Output destinationsPreliminary Four MVX 44 / 48 / 84 / 88 VGA Matrix Switchers Remote Operation Host-to-Switcher instructionsSimple Instruction Set Control Switcher-initiated messages Using the command/response table Switcher error responsesSymbol definitions Command Ascii command Response Additional Description$ *X% G InX$ AudX Audio mute commands Preliminary EVM EZG Responds with the Go prompt Loading firmware using an SIS commandClick the Files of type drop box and select All files This message indicates that the firmware upload is complete File figureExit HyperTerminal Scroll to the desired program and click Install figure Matrix Switchers Control ProgramInstalling the software Click the Software tab figureOverview Using the softwareTo run the Matrix Switchers Control Program, click Comm Port Selection window -8 appearsExtron Matrix Switchers Control Program window blank Updating the firmware 11 Open windowMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Remote Operation Windows buttons, drop boxes, and trash Windows menus File menu13 RGB Delay/Mute/Output-Volume Adjust window Tools menuPreferences menu 15 Ties shown as lines16 Ties shown as crosspoints Using Emulation mode Master-Reset selectionUsing the help system Help menu on the main screenPreliminary AppendixAA Specifications and Part Numbers SpecificationsSync Specifications and Part Numbers, cont’d Matrix switcher part numbers Part number Part Numbers and AccessoriesMVX matrix switcher part numbers Included partsAccessories CablesMale-to-male VGA cable Part number Install kit Part numberVGA to 5 BNC cables Part number Preliminary Extron Electronics, Europe Asia JapanExtron USA West

MVX 88 Series specifications

The Extron MVX 88 Series is a cutting-edge technology solution designed to facilitate seamless audio and video signal routing in a variety of settings, from educational institutions to corporate environments. This versatile matrix switcher series supports the demanding needs required for high-performance AV distribution.

One of the key features of the MVX 88 Series is its ability to handle multiple input and output formats, including HDMI, VGA, and composite video, ensuring versatility in connecting various devices. It supports resolutions up to 1920x1200 at 60 Hz, providing crystal-clear image quality. The series 8x8 matrix switcher allows users to route any input to any output, offering maximum flexibility in AV configurations. This means that users can easily switch between multiple sources without the need for complex wiring.

Another notable characteristic of the MVX 88 Series is its integrated scaling capabilities. Each output has a built-in video scaler that adjusts the input signal to match the required resolution of the display device. This technology enhances viewing experiences by eliminating compatibility issues, making it easier to connect different devices and ensuring optimal picture clarity.

The Extron MVX 88 Series also boasts advanced audio functionality. It features a built-in audio router and supports various audio formats, allowing users to manage audio signals alongside video. This capability is crucial for applications where synchronized audio and video output is essential, such as presentations and video conferences.

In terms of control, the MVX 88 Series is designed for ease of use. It includes an intuitive front panel interface, allowing users to quickly select inputs and outputs. Additionally, it supports various external control options, including RS-232 and Ethernet, making it compatible with a wide range of control systems. This adaptability simplifies integration into existing AV setups.

Durability and reliability are critical aspects of the MVX 88 Series. It is built to withstand rigorous daily use, featuring a robust enclosure that protects the internal components. Furthermore, Extron's commitment to quality ensures that users can depend on the MVX 88 for consistent performance in all applications.

Overall, the Extron MVX 88 Series stands out in the realm of AV matrix switchers, offering remarkable features, advanced technologies, and user-friendly characteristics that meet the demands of modern AV environments. Whether for classrooms, conference rooms, or control centers, the MVX 88 Series is an ideal solution for comprehensive audio and video management.
Top Page Image Contents