Extron electronic MVX 88 Series manual Loading firmware using an SIS command

Page 61

Loading firmware using an SIS command

NFirmware can be uploaded two ways:

1. Using the Matrix Switchers Control Program.

2. Using the Eupload SIS command entered via a communications utility such as HyperTerminal.

Extron recommends that you upload firmware using the Matrix Switchers Control Program (see “Updating the firmware” on page 4-16) and reserve this SIS procedure for correcting firmware that has been corrupted and unable to respond to the Matrix Switchers Control Program.

Firmware can be loaded using SIS commands as follows:

1.

Visit the Extron web site, www.extron.com, select the MVX switcher product

 

category, select the latest firmware file for download, and copy it to your

 

computer. Note the folder to which you save the firmware file.

2.

Start a communications utility such as HyperTerminal. Select the Comm port

 

that is connected to the switcher’s RS-232 port. Use 9600 bits per second, 8

 

data bits, “none” parity, 1 stop bit, and “none” flow control.

NIf you are performing this procedure to recover from corrupted firmware, the switcher will respond only to the “n”, “q”, and “Eupload” SIS commands.

NThe firmware upload can take several minutes. If HyperTerminal’s echo function is turned off, you will have no indication that the upload is progressing. If desired, turn on the echo function as follows (figure 4-3): Click File >

Properties > Settings > ASCII Setup..., check the Echo typed characters locally checkbox, and then click Ok twice.

Figure 4-3 — Turn on the echo function

3.

Depress the keyboard’s Esc key and then type upload. The computer

 

responds with the “Go” prompt.

4.

Click Transfer > Send text file... .

5.

Click the Files of type: drop box and select All files (*.*).

PRELIMINARY

MVX 44 / 48 / 84 / 88 VGA Matrix Switchers • Remote Operation 4-11

Page 60 Page 62
Image 61
Page 60 Page 62
Contents MVX 44 / 48 / 84 / 88 series VGA Matrix SwitcherConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolFCC Class a Notice Page MVX 44 / 48 / 84 / 88 VGA Matrix Switchers Quick Start QS-1 Quick Start MVX Series VGA Matrix SwitchersSaving or recalling a preset Powering upViewing and adjusting the audio input gain QS-2 MVX 44 / 48 / 84 / 88 VGA Matrix Switchers Quick StartTable of Contents Table of Contents, cont’d One MVX 44 / 48 / 84 / 88 VGA Matrix Switchers Introduction About the SwitchersAny input to any or all outputs FeaturesIntroduction, cont’d Two Rack mounting the switcher Mounting the SwitcherTabletop use Mounting the switcher Furniture mounting the switcherVideo and audio input connections Cabling and Rear Panel ViewsStrap the audio cable to the extended tail of the connector RGB video output connectors Connect Rgbhv videoVideo and audio output connections Control of the switcher Power connectionRemote connection Three MVX 44 / 48 / 84 / 88 VGA Matrix Switchers Operation Front Panel Controls and IndicatorsDefinitions Input and output selection controls and indicators Infrared sensor and Power/audio/data LEDPower/data/audio LED O and Audio Setup button Selection and audio/video controls and indicatorsControl buttons and LEDs Video/+dB LED and Audio/-dB LEDAttenuation on Ignores the commandButton is released or the lower limit is reached Has reached the maximum attenuation -18 dBOperations Powering up the switcherCreating a set of ties Select video and audio for the tie figure Example 1 Create a set of video and audio tiesPress and release the Input 5 button figure Press and release the Enter button figure Current configuration -7 is nowSelect video only for the tie figure Example 2 Add a video tie to a set of video and audio tiesPress and release the Output 1 button figure Press and release the Enter button figureExample 3 Remove a tie from a set of ties Current configuration -12 is nowSelect audio only for the tie figure 15 Deselect the output Press and release the Output 4 button figureExample 4 View ties by selecting an input Viewing the configurationSelect both video and audio for viewing figure Press and release the I/O button figure Press and release the I/O button figurePress and release the Output 3 button figure Example 5 View ties by selecting outputs24 Deselect audio to view video ties only Example 6 Save a preset Using presetsPreset 2 Preset Example 7 Recall a presetPress and release the Input 1 button figure Adjusting input audio gain and attenuationPreliminary = unlit, = blinking LED Example 8 Adjust the input audio gain+2 dB Output 1 LED + 2 pressesSaved Example 9 Resetting audio gain single inputExample 10 Resetting audio gain all inputs Setting the output audio levelPress and release the and buttons simultaneously figure Clearing all ties and presets Front panel security lockout Executive modeMemory Resetting the system to factory defaultsOptimizing the Audio TroubleshootingWorksheet example 1 System equipment WorksheetsMain VTGClassical music from the CD player input 5 is Worksheet example 2 Daily configuration45 Worksheet example 3 Test configuration Worksheet example 3 Test configurationPreliminary Input sources Output destinations Configuration worksheetPreliminary Four MVX 44 / 48 / 84 / 88 VGA Matrix Switchers Remote Operation Host-to-Switcher instructionsSimple Instruction Set Control Switcher-initiated messages Using the command/response table Switcher error responsesSymbol definitions Description Command Ascii command Response Additional$ *X% G InX$ AudX Audio mute commands Preliminary EVM EZG Responds with the Go prompt Loading firmware using an SIS commandClick the Files of type drop box and select All files This message indicates that the firmware upload is complete File figureExit HyperTerminal Installing the software Matrix Switchers Control ProgramScroll to the desired program and click Install figure Click the Software tab figureTo run the Matrix Switchers Control Program, click Using the softwareOverview Comm Port Selection window -8 appearsExtron Matrix Switchers Control Program window blank 11 Open window Updating the firmwareMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Remote Operation Windows menus File menu Windows buttons, drop boxes, and trashTools menu 13 RGB Delay/Mute/Output-Volume Adjust window15 Ties shown as lines Preferences menu16 Ties shown as crosspoints Master-Reset selection Using Emulation modeHelp menu on the main screen Using the help systemPreliminary AppendixAA Specifications Specifications and Part NumbersSync Specifications and Part Numbers, cont’d MVX matrix switcher part numbers Part Numbers and AccessoriesMatrix switcher part numbers Part number Included partsCables AccessoriesMale-to-male VGA cable Part number Install kit Part numberVGA to 5 BNC cables Part number Preliminary Asia Japan Extron Electronics, EuropeExtron USA West

MVX 88 Series specifications

The Extron MVX 88 Series is a cutting-edge technology solution designed to facilitate seamless audio and video signal routing in a variety of settings, from educational institutions to corporate environments. This versatile matrix switcher series supports the demanding needs required for high-performance AV distribution.

One of the key features of the MVX 88 Series is its ability to handle multiple input and output formats, including HDMI, VGA, and composite video, ensuring versatility in connecting various devices. It supports resolutions up to 1920x1200 at 60 Hz, providing crystal-clear image quality. The series 8x8 matrix switcher allows users to route any input to any output, offering maximum flexibility in AV configurations. This means that users can easily switch between multiple sources without the need for complex wiring.

Another notable characteristic of the MVX 88 Series is its integrated scaling capabilities. Each output has a built-in video scaler that adjusts the input signal to match the required resolution of the display device. This technology enhances viewing experiences by eliminating compatibility issues, making it easier to connect different devices and ensuring optimal picture clarity.

The Extron MVX 88 Series also boasts advanced audio functionality. It features a built-in audio router and supports various audio formats, allowing users to manage audio signals alongside video. This capability is crucial for applications where synchronized audio and video output is essential, such as presentations and video conferences.

In terms of control, the MVX 88 Series is designed for ease of use. It includes an intuitive front panel interface, allowing users to quickly select inputs and outputs. Additionally, it supports various external control options, including RS-232 and Ethernet, making it compatible with a wide range of control systems. This adaptability simplifies integration into existing AV setups.

Durability and reliability are critical aspects of the MVX 88 Series. It is built to withstand rigorous daily use, featuring a robust enclosure that protects the internal components. Furthermore, Extron's commitment to quality ensures that users can depend on the MVX 88 for consistent performance in all applications.

Overall, the Extron MVX 88 Series stands out in the realm of AV matrix switchers, offering remarkable features, advanced technologies, and user-friendly characteristics that meet the demands of modern AV environments. Whether for classrooms, conference rooms, or control centers, the MVX 88 Series is an ideal solution for comprehensive audio and video management.
Top Page Image Contents