Extron electronic MTP 1500RL 15HD RS SEQ installation instructions Mounting, Connect Input

MTP 1500RL 15HD RS SEQ • Setup Guide

This guide provides basic instructions for an experienced installer to set up and operate the Extron MTP 1500RL 15HD RS SEQ twisted pair receiver.

For full details, see the MTP 1500RL 15HD RS SEQ User Guide, available online at www.extron.com.

RED LEVEL PEAKING

SELECTGREEN

BLUE	ADJUST		MIN/MAX
DELAY		RGB	MTP 1500RL SERIES

								:
					TANT complete
	IMPOR.com						for	the			and
							instructions,
		xtr
	.e		on							the
to
	www	installationoreconnectingce
										.
Go guide,				bef		power			sour
user					the
specifications
	product			to

INPUT BUFFERED OUTPUT

POWER 12V 1.0A MAX

MTPMTP

OUTPUT	H +	V +	CSYNC SOG VIDEO END BI-232
RS-232
	ON
Tx Rx	MTP 1500RL 15HD RS SEQ

Installation and Setup

Step 1 — Mounting

Turn off or disconnect all equipment power sources. Mount the MTP 1500RL 15HD RS SEQ receiver as required.

Step 2 — Connect Input

Connect the RJ-45 cable from an MTP transmitter to the Input port on the MTP 1500RL 15HD RS SEQ receiver.

Terminate the cable as shown below right, using the same standard (T568A or T568B) at both ends.

Transmission distance with one device before the MTP 1500RL 15HD RS SEQ

Pin

T568A Wire

T568B Wire

1500 feet (457 m) maximum (video signals)

Color

Color

Input

VGA

MTP Tx

TP

MTP 1500RL

VGA

1

White-green

White-orange

cable

cable

cable

Display

RJ-45 Connector

Source

Device

15HD RS Device

Pins:

2

Green

Orange

12345678

1000 feet (305 m) maximum

3

White-orange

White-green

(RS-232 data signals)

4

Blue

Blue

Transmission distance with more than one device before the MTP 1500RL 15HD RS SEQ

5

White-blue

White-blue

1500 feet (457 m) maximum (video signals)

6

Orange

Green

Input

VGA

MTP Tx

TP

MTP RL Rx

TP

MTP 1500RL

VGA

7

White-brown

White-brown

cable

cable

cable

cable

Display

Source

Device

Device

15HD RS Device

Insert Twisted

8

Brown

Brown

Pair Wires

1000 feet (305 m) maximum

(RS-232 data signals)

NOTE: The transmitter and receiver are designed for and perform best with Extron Enhanced Skew-Free™AV cable terminated in accordance with the TIA/EIA T568A standard. CAT 5 cables are acceptable but less preferable. Using preterminated and tested cables is also recommended. Cables terminated on site should be tested before use to ensure that they comply with Category 5 specifications.

Step 3 — Connect Outputs

Attach the applicable output cables (video, audio, and buffered output).

A.High resolution video output — Connect a suitable display device to the 15-pin HD connector (RGB).

B.RS-232 connector — Connect an RS-232 compatible MTP transmitter to the 3-pole captive screw connector (wired as shown at right) for bi-directional or uni-directional communication up to 1,000 feet, (305 meters) maximum.

C.Buffered output — Connect up to 5 daisy-chained MTP receivers to this RJ-45 connector.

Step 4 — Receiver DIP Switches

•H sync (H+) and V sync (V+) switches — Set these switches up (On) for positive sync or down (Off) for negative sync.

•Composite Sync, SOG, and Video switches — Set these switches as shown in the table (see right) to output the indicated format.

•End Unit switch — Set this switch up if either of the following is true:

•The receiver being configured is the only receiver connected to the transmitter.

•The receiver being configured is the last receiver in a daisy-chained system.

•BI-232 switch — Set this up (ON) for bi-directional or down for uni-directional communication.

Connected RS-232	MTP Reciever
Device Pins	Pins
Receive	Tx
Transmit	Rx
Ground	Gnd
	H + V + CSYNC SOG VIDEO END BI-232
	ON
Output	C Sync SOG Video
Format

RGBHV

RGBS

RGsB

Component*

S-video*

Composite*

* Input video format must match.