Extron electronic XTP T HDMI, XTP R HDMI manual Front Panel Configuration Port, Audio Output Wiring

Page 13

EAnalog audio output — Connect a balanced or unbalanced, stereo or mono audio output device to the 3.5 mm, 5-pole captive screw connector for 2-channel stereo analog audio output. If the device is receiving 2-channel LPCM embedded on the HDMI input signal and digital is the selected audio input format, it is extracted and converted to a stereo analog signal.

Tip

Ring

Sleeves

Tip

Ring

 

No Ground Here

 

 

L

Tip

L

 

 

 

 

 

Sleeves

 

 

R

Tip

R

Do not tin the wires!

 

No Ground Here

 

 

Balanced Audio Output

Unbalanced Audio Output

Figure 5. Audio Output Wiring

ATTENTION: For unbalanced audio, connect the sleeves to the center contact ground. Do not connect the sleeves to the negative (-) contacts.

FS/PDIF audio output — Connect an audio device to the female orange RCA connector for digital S/PDIF audio output (see Audio Output Overview on page 15 for supported audio formats on the S/PDIF output). The type of audio present on this output will be dictated by the following:

The audio format selected on the source material or device.

The source device automatically outputting an audio format through EDID.

GRelays — Connect equipment that can be controlled via momentary or latching contact, like as projector screens or lifts, to the normally open relays.

ATTENTION: Do not exceed 24 V at 1.0 A for each port.

HPower connector and LED — Connect the external 12 V, 1.0 A power supply to the

2-pole captive screw connector. The Power LED lights to indicate the device is receiving power.

NOTE: XTP HDMI transmitters and receivers can be powered remotely (see Power Connection on page 11).

Front Panel Configuration Port

 

 

 

INPUT

 

 

 

CONFIG

SIGNAL

HDMI AUDIO

AUDIO SIGNAL CLIP

 

 

HDCP

ANALOG AUDIO

 

 

 

 

 

 

 

 

 

 

XTP T HDMI

XTP T HDMI

a

 

 

 

 

 

 

XTP

 

AUDIO

 

 

CONFIG

SIGNAL

HBR

BITSTREAM

LPCM

 

 

 

 

 

 

 

HDCP

HDMI

S/PDIF

ANALOG

 

 

 

 

 

XTP R HDMI

XTP R HDMI

Figure 6. Front Panel Configuration Port

AFront Panel Config Port — Connect a host device to the female mini-USB B port to configure the connected transmitter or receiver or update firmware.

XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation

7

Image 13
Contents XTP T Hdmi XTP R Hdmi Safety Instructions English Chinese Simplified(简体中文) Registered Trademarks FCC Class a NoticeSoftware Commands Specifications AvailabilityConventions Used in this Guide NotificationsContents XTP T Hdmi Transmitter and XTP R Hdmi Receiver Contents About This Guide IntroductionAbout the XTP Hdmi Transmitter and Receiver Typical XTP Hdmi Transmitter and Receiver Matrix Application Key FeaturesXTP T Hdmi Transmitter and XTP R Hdmi Receiver Introduction XTP T Hdmi Rear Panel Connectors Installation OperationCabling RS-232 IR XTP R Hdmi Connectors XTP R Hdmi Rear Panel ConnectorsAudio Output Wiring Front Panel Configuration PortHdmi LockIt Making ConnectionsSupported cables TP Cable Termination and RecommendationsCable recommendations RS-232 and IR Communication Wiring the RS-232 and IR ConnectorLocal power Power ConnectionTypical Point-to-Point Application with Remote Power Remote powerXTP R Hdmi Front Panel Indicators XTP T Hdmi Front Panel IndicatorsInput indicators XTP indicatorsAudio indicators Hdmi Audio SwitchReset Mode Summary Reset ModesAudio Output Overview Audio Output Audio Input FormatHost Device Connection SIS Configuration ControlSIS Programming Guide Host-to-Device and Device-to-Host CommunicationUsing the Command and Response Table for SIS Commands Error ResponsesSymbol definitions X2@ Edid Emulation Table where X2@ = the SIS valueAudio Configuration Command and Response Tables for Transmitter SIS CommandsAdvanced Configuration Volume control Command and Response Tables for Receiver SIS CommandsAudio mute Relay controlQuery Hdcp output Installing the XTP System Configuration Software XTP System Configuration SoftwareTo install the software from the DVD Connection Using the XTP System Configuration SoftwareTo download the software from the website Transmitter device settings Transmitter ConfigurationEdid Minder Screen Edid MinderTo clear the currently applied filters To use a filter or combination of filtersReceiver Device Settings Screen Receiver ConfigurationMounting Reference InformationTabletop Mounting Mounting KitsUpdating Firmware with Firmware Loader Installing Firmware LoaderDownloading Extron Firmware Loader Downloading Firmware from the Extron Website Downloading FirmwareAdd Device... Dialog Box Installing Firmware with Firmware LoaderExtron Warranty

XTP T HDMI, XTP R HDMI specifications

Extron Electronics is a renowned manufacturer of advanced technology solutions for the audiovisual industry. Among their cutting-edge products is the XTP R HDMI and XTP T HDMI, both of which play pivotal roles in signal transmission and distribution within complex AV environments.

The Extron XTP R HDMI is a powerful receiver designed to work seamlessly with Extron’s XTP Systems. This device offers robust HDMI signal processing and is capable of transmitting high-definition video and audio signals over long distances using standard twisted pair cabling. One of its main features is the ability to support resolutions up to 4K at 60 Hz, including HDCP 2.2 compliance, which is essential for transmitting protected content. The XTP R HDMI also includes various audio extraction options, allowing users to separate audio from the HDMI signal for independent audio processing.

On the other hand, the XTP T HDMI serves as a transmitter within the same ecosystem, designed to convert HDMI video and audio signals into a format suitable for long-distance transmission. This device also supports 4K resolution and comes with a variety of input options that can cater to diverse installation needs. The XTP T HDMI is equipped with scaling capabilities, enabling users to select a preferred output resolution to match display capabilities, ensuring optimal performance in varied AV environments.

One of the standout technologies included in both the XTP R HDMI and XTP T HDMI is the Extron XTP technology, which provides a robust and reliable way to distribute AV signals over a single twisted pair cable. This technology allows signals to travel distances up to 330 feet (100 meters) without compromising signal quality. Additionally, both units support various formats, including HDMI, allowing for comprehensive compatibility with various sources and displays.

The XTP systems offer flexible setup options with features such as EDID communication, which ensures that the source device can communicate effectively with the display for the best possible image quality. Furthermore, integration with Extron’s proprietary Global Configurator software facilitates simplified configuration and programming, leading to smoother installations and management.

In summary, the Extron XTP R HDMI and XTP T HDMI are essential components for professional AV setups, providing excellent performance in signal transmission with advanced features and technologies that ensure superior integration and functionality in diverse applications.