Gigabyte GA-K8VT800 user manual SATA0/ SATA1 Serial ATA Connector, Pwrled

Page 21

7)SATA0/ SATA1 (Serial ATA Connector)

Serial ATA can provide up to 150MB/s transfer rate. Please refer to the BIOS setting for the Serial ATA and install the proper driver in order to work properly.

 

 

Pin No.

Definition

 

 

1

GND

1

7

2

TXP

 

 

3

TXN

 

 

4

GND

 

 

5

RXN

 

 

6

RXP

 

 

7

GND

8)PWR_LED

PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode.

 

Pin No.

Definition

1

1

MPD+

2

MPD-

 

3

MPD-

English

- 21 -

Hardware Installation

Image 21
Contents GA-K8VT800 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation K8VT800-GA GA-K8VT800 Motherboard LayoutBlock Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature SummaryBios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of MemoryDDR1 DDR2 DDR3 Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector IDE1 / IDE2 IDE Connector FDD FDD ConnectorPwrled SATA0/ SATA1 Serial ATA ConnectorFpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel ConnectorSurcen Surround Center Connector Spdifio Spdif In / Out Connector15 IR USB1 / FUSB2 Front USB ConnectorClrcmos Clear Cmos BatteryEnglish English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E8 „ Set Supervisor Password „ Load Optimized Defaults„ Set User Password „ Save & Exit SetupTime Standard Cmos FeaturesIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave IDE Channel 2/3 MasterHalt on Drive A/Drive BMemory Base MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Password CheckRAID Integrated PeripheralsUart Mode Select OnBoard LAN Boot ROMUSB 2.0 Controller USB Keyboard SupportParallel Port Mode UR2 Duplex ModeOnboard Parallel Port Midi Port AddressAcpi OS Power Management SetupResume by Alarm PME Event Wake UpModem Ring Resume INT PnP/PCI ConfigurationsPC Health Status Current CPU TemperatureCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPMFrequency/Voltage Control Load Fail-Safe Defaults Top PerformanceDimm OverVoltage control Set Supervisor/User Password Load Optimized DefaultsExit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish What is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery Unique Software UtilitiesF9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the VIA VT8237 RAID BiosCreate RAID Array Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete a RAID array Delete Array¡G Installing the RAID drivers 4 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English Surround-Kit connector Spdif cable connector English Spdif Output Device Optional Device Introduction of audio connectors Jack-Sensing and UAJ IntroductionAuto-detecting Manual setting Enable UAJ functionUAJ Introduction AMI Bios Beep Codes TroubleshootingEnglish Taiwan Headquarters Contact UsChina Shanghai