Gigabyte GA-7VA1004 manual Halt on, Base Memory, Extended Memory

Page 34

English

FHalt on

The category determines whether the computer will stop if an error is detected during power up.

8NO Errors

The sy stem bootw ill not stop for any error thatmay be detected

 

and y ou will be prompted.

8All Errors

Whenev er the BIOS detects a non-fatal error the sy stem w ill be stopped.

8All, But Keyboar

The sy stem bootw ill not stop for a key board error; it w ill stop for

 

all other errors. (Defaultv alue)

8All, But Diskette

The sy stem boot will notstop for a disk error; it w ill stop for all

 

other errors.

8All,But Disk/Key

The sy stem boot w ill notstop for a key board or disk error; it will

 

stop for all other errors.

Memory

The category is display -only which is determined by POST (Power On Self Test) of the BIOS.

Base Memory

The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system.

The value of the base memory is typically 512 K for sy stems with 512 K memory installed on the motherboard, or 640 K for systems with 640 K or more memory installed on the motherboard.

Extended Memory

The BIOS determines how much extended memory is present during the P OST. This is the amount of memory located above 1 MB in the CPU’s memory address map.

GA-7VA Motherboard

- 28 -

Image 34
Contents AGP 4X/8X notc h Page Declaration of Conformity Declaration of Conformity Supplementary InformationPage Page GA-7VA Table of Content Table of Content Item Checklist Installing the motherboard to the chassis…Chapter Introduction CPUBios GA-7VA Motherboard Layout Hardware Installation Process StepSW1 CPU Clock SW1OFF Pin1 indicator 3CPU Heat Sink Installation Install memory modules DDRInstall expansion cards DDR IntroductionUSB Connector PS/2 Keyboard and PS/2 Mouse ConnectorUSB Game /MIDI Ports Audio ConnectorsParallel Port ,VGA port and Serial Ports Coma Coma CombConnectors Introduction 4ATXPOWER ATX Power 1CPUFAN CPU FAN Connector2SYSFAN System FAN Connector GNDIDE2 5IDE1/ IDE2 IDE1/IDE2 Connector6FDD Floppy Connector IDE19FPANEL 2x10 pins connector MSG+ PW+ PW SPK HD+ HD RES RES+13CDIN CD 11FAUDIO Faudio Connector14AUXIN AUX In Connector 15SPDIF SPDIFOutVCC Spdif GND 17F USB1 / FUSB2 Front USB Conn ector, YellowFUSB1 FUSB2 English Bios Setup Main Menu For example Bios Ver. E2 Load Fail-Safe Defaults Power Management S etup PnP/PCI Configurations Load Optimized DefaultsDate Standard Cmos FeaturesTime IDE Primary Mas ter, S lave / Secondary Master, Slave Floppy 3 Mode Support for Japan AreaFDrive a / Drive B Base Memory Halt onMemory Extended MemoryAdvanced Bios Features FFirst / S econd / Third Boot deviceBoot Up Floppy Seek FInit Display FirstIntegrated Peripherals Bios Setup Integrated PeripheralsIDE1 Conductor Cable OnChip IDE Channel0OnChip IDE Channel1 IDE2 Conductor CableUS B Mouse Support Fusb 2.0 ControllerUS B Keyboard S upport FOnboard Serial PortFMidi Port Address FParallel Port ModeFGame Port Address Midi Port IRQPower Management Setup Acpi Suspend Type Keyboard Power OnMouse Power On Soft-off by PwrbtnFResume by Alarm PME Event Wak e upFPCI2 IRQ Ass ignment PnP/PCI ConfigurationsFPCI1/PCI5 IRQ Assignment FPCI3 IRQ Ass ignmentPC Health Status CRes et Case Open Status CCase OpenedCurrent CPU FAN / S YS TEM FAN Speed RPM Current CPU Temperature CCPU Shutdown Temperature Fan Fail Warning CPU / SystemSpread spectrum Modulated CPU Host Frequency MHz By switch SW1Frequency/Voltage Control CPU Host Clock ControlCPU OverVoltage Control PCI/AGP Frequency MHzDram Clock MHz AGP OverVoltage ControlEnabled DisabledTop Performance Load Fail-Safe Defaults Load Fail-Safe Defaults? Y/N ?NLoad Optimized Defaults Load Optimized Defaults? Y/N ?NSet Supervisor/User Password Enter PasswordSave & Exit Setup Save to Cmos and Exit Y/N? YExit Without Saving Quit Without Saving Y/N? NEnglish English Technical Reference Bios Flash Procedureyte @BIOSTM Program to flash Bios StepEnglish English English English Hifg Amibios Setup Bios Features Setup COMMAND.COM 7VTX.F4 EXIT? Load Setup Defaults? Y/N ?N Congratulate you have accomplished the Bios flash procedure What is Q-Flash Utility? How to use Q-Flash?Load Bios FromFloppy XXXX.XXClick Gigabyte Utilities English @ Bios Introduction Easy TuneTM 4 Introduction Ster eo Speakers C onnection and Settings 6-Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode SURROUND-KIT access analog output to rear Basic & Advanced 6 Channel Analog Audio Output ModeNotes Spdif Output Device Optional Device Memo English Appendix Picture below are shown in Windows XP CD driver versionUSB Patch Driver VIA USB2.0 DriverEnglish Appendix B RealTek AC97 Audio Driver Appendix C EasyTune4 Utilities Installation Appendix D Acronyms Midi LBALED MTHHDD CD-ROM DVD-ROM Technical Support/RMA SheetAMR / CNR Samsung DDR MShould you need to find new support list, pls refer toMicron DDR AdataTroubleshooting END English Memo English