Gigabyte GA-EP45-UD3LR user manual Configuring Sata controller mode in Bios Setup, Raid

Page 80

B. Configuring SATA controller mode in BIOS Setup

Make sure to configure the SATA controller mode correctly in system BIOS Setup .

Step 1:

Turn on your computer and press <Delete> to enter BIOS Setup during the POST (Power-On Self-Test). To create RAID, set SATA RAID/AHCI Mode under the Integrated Peripherals menu to RAID (Figure 1)(Disabled by default). If you do not want to create RAID, set this item to Disabled or AHCI.

CMOS Setup Utility-Copyright (C) 1984-2008 Award Software

Integrated Peripherals

	SATA RAID/AHCI Mode		[RAID]				Item Help
	SATA Port0-3 Native Mode		[Disabled]			Menu Level
	SATA Port0-3 Native Mode		[Disabled]			Menu Level
	USB Controller		[Enabled]
	USB 2.0 Controller		[Enabled]
	USB Keyboard Support		[Disabled]
	USB Mouse Support		[Disabled]
	Legacy USB storage detect		[Enabled]
	Azalia Codec		[Auto]
	Onboard H/W LAN		[Enabled]
	Green LAN		[Disbabled]
	 SMART LAN		[Press Enter]
	Onboard LAN Boot ROM		[Disabled]
	Onboard IDE Controller		[Enabled]
	Onboard Serial Port 1		[3F8/IRQ4]
	Onboard Parallel Port		[378/IRQ7]
	Parallel Port Mode		[SPP]
	: Move	Enter: Select	+/-/PU/PD: Value	F10: Save		ESC: Exit	F1: General Help
	F5: Previous Values		F6: Fail-Safe Default			F7: Optimized Defaults

Figure 1

Step 2:

Save changes and exit BIOS Setup.

The BIOS Setup menus described in this section may differ from the exact settings for your motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you have and the BIOS version.

GA-EP45-UD3LR/UD3L Motherboard

- 80 -

Image 80

Contents GA-EP45-UD3LR/ GA-EP45-UD3L Motherboard Copyright DisclaimerDocumentation Classifications Identifying Your Motherboard RevisionTable of Contents Drivers Installation Box Contents GA-EP45-UD3LR/GA-EP45-UD3L Motherboard Layout Block Diagram Hardware Installation Installation PrecautionsProduct Specifications CPUPage Bios Installing the CPU and CPU Cooler Installing the CPUCPU Socket Lever Installing the CPU Cooler Installing the Memory Dual Channel Memory ConfigurationInstalling a Memory Installing an Expansion Card Back Panel Connectors Center/Subwoofer Speaker Out Jack Orange Rear Speaker Out Jack BlackSide Speaker Out Jack Gray Line In Jack BlueInternal Connectors SATA20/1/2/3/4/5GND FDD Floppy Disk Drive Connector 5 CPUFAN/SYSFAN1/SYSFAN2/PWRFAN Fan HeadersIDE IDE Connector SATA20/1/2/3/4/5 Sata 3Gb/s ConnectorsPwrled System Power LED Header Faudio Front Panel Audio Header PW Power Switch, Red Fpanel Front Panel HeaderCdin CD In Connector, Black Spdifi S/PDIF In Header, RedSpdifo S/PDIF Out Header FUSB1/FUSB2 USB Headers, YellowLPT Parallel Port Header Coma Serial Port Header, WhiteCI Chassis Intrusion Header Clrcmos Clearing Cmos JumperBAT Battery Bios Setup Logo Screen Default Post Screen Startup ScreenFunction Keys End Q-FLASHSample Bios Version GA-EP45-UD3L E19 Bios Setup Program Function KeysMain Menu Main Menu Help Standard Cmos Features  Advanced Bios Features Power Management Setup  PnP/PCI ConfigurationsMB Intelligent TweakerM.I.T SPDRobust Graphics Booster CPU Clock Ratio NoteFine CPU Clock Ratio Note CPU FrequencyCPU Host Frequency Mhz PCI Express Frequency MhzA.2 Advanced Clok ControlCPU Clock Drive PCI Express Clock DriveCPU Clock Skew MCH Clock SkewCommand RateCMD CAS Latency TimeTRCD TRPChannel A/B Timing Settings TRD Phase0 AdjustmentTRD Phase1 Adjustment TRD Phase2 AdjustmentChannel A/B Driving Settings DDR Write TrainingDriving Strength Profile Data Driving Pull-Up LevelLoad-Line Calibration CPU VcoreCPU Termination CPU ReferenceIDE Channel 0, 1 Master/Slave DateTime Floppy 3 Mode Support IDE Channel 2, 3 Master, IDE Channel 4 Master/SlaveDrive a Halt OnHard Disk Boot Priority First/Second/Third Boot DevicePassword Check HDD S.M.A.R.T. CapabilityCPU Multi-Threading Note Limit Cpuid Max. to 3 NoteNo-Execute Memory Protect Note CPU Enhanced Halt C1ENoteInit Display First Delay For HDD SecsFull Screen Logo Show Integrated Peripherals Smart LAN LAN Cable Diagnostic Function USB ControllerUSB 2.0 Controller USB Keyboard SupportOnboard LAN Boot ROM Parallel Port ModeOnboard IDE Controller JMicron 368 Chip Onboard Serial PortPME Event Wake Up Power On by RingSoft-Off by PWR-BTTN Resume by Alarm Hpet Mode NotePower On By Mouse Power On By KeyboardPCI2 IRQ Assignment PnP/PCI ConfigurationsPCI1 IRQ Assignment Reset Case Open Status Current System/CPU TemperatureCurrent CPU/SYSTEM/POWER FAN Speed RPM CPU Warning TemperatureCPU Smart FAN Mode CPU Smart FAN ControlLoad Fail-Safe Defaults Load Optimized DefaultsSupervisor Password User PasswordSave & Exit Setup Exit Without SavingDrivers Installation Installing Chipset DriversApplication Software Technical ManualsContact SystemDownload Center System Requirements Xpress Recovery2Before You Begin Installation and Configuration Installing Windows XP and Partitioning the Hard DrivePage Accessing Xpress Recovery2 Using the Backup Function in Xpress Recovery2Exiting Xpress Recovery2 Using the Restore Function in Xpress Recovery2Removing the Backup Bios Update Utilities Updating the Bios with the Q-Flash UtilityWhat is DualBIOSTM? What is Q-FlashTM?Updating the Bios Load Optimized DefaultsSaveY/N?& ExitY Setup Updating the Bios with the @BIOS Utility Using @BIOSAfter Updating the Bios Update the Bios Using the Internet Update FunctionEasyTune EasyTune 6 Interface Tabs InformationDynamic Energy Saver Advanced Dynamic Energy Saver Advanced Interface Meter ModeMeter Mode Button Information Table Stealth Mode Total ModeTotal Mode Button Information Table Options Descriptions Directions for using Q-ShareShare Preference Screen System RestoreTime Repair Configuring Sata Hard Drives Configuring the Onboard Sata ControllerTo configure Sata hard drives, follow the steps below Installing Sata hard drives in your computerConfiguring Sata controller mode in Bios Setup RAIDConfiguring a RAID array in RAID Bios Create RAID VolumeCreate Volume Menu ST3120026AS 3JT329JX 111.8GB Delete RAID Volume Delete Volume MenuRequired for Ahci and RAID Mode Making a Sata RAID/AHCI Driver DiskettePage Installing the Sata RAID/AHCI Driver and Operating System Installing Windows XPENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Installing Windows Vista Page Configuring Audio Input and Output Configuring 2/4/5.1/7.1-Channel AudioConfiguring Speakers High Definition Audio HD AudioMuting the Back Panel Audio For HD Audio Only Configuring Sound EffectActivating an AC97 Front Panel Audio Module Pdif Installing the S/PDIF In Cable OptionalInstalling the S/PDIF In Cable Conneting a S/PDIF out Cable Configuring S/PDIF outPdif Out Configuring Microphone Recording Select Realtek HD Audio Input in the Mixer device list Playing the Sound Using the Sound RecorderRecording the Sound Troubleshooting Frequently Asked QuestionsTroubleshooting Procedure StartEND Weee Symbol Statement Regulatory StatementsRegulatory Notices Our Commitment to Preserving the EnvironmentChina Restriction of Hazardous Substances Table GA-EP45-UD3LR/UD3L Motherboard 104 105 Appendix GA-EP45-UD3LR/UD3L Motherboard 106 107 Appendix GA-EP45-UD3LR/UD3L Motherboard 108 109 Appendix GA-EP45-UD3LR/UD3L Motherboard 110 Contact Us  G.B.T. INC USA Mexico Gigabyte Global Service System