Gigabyte GA-EP45-UD3LR user manual Onboard LAN Boot ROM, Onboard IDE Controller JMicron 368 Chip

Page 52

When LAN Cable Is Functioning Normally...

If no cable problem is detected on the LAN cable connected to a Gigabit hub or a 10/100 Mbps hub, the following message will appear:

Start detecting at Port.....

Link Detected --> 100Mbps

Cable Length= 30m

Link Detected	Displays transmission speed
Cable Length	Displays the approximate length of the attached LAN cable.

Note: The Gigabit hub will only operate at a speed of 10/100 Mbps in MS-DOS mode; it will operate at a normal speed of 10/100/1000 Mbps in Windows mode or when the LAN Boot ROM is activated.

When a Cable Problem Occurs...

If a cable problem occurs on a specified pair of wires, the Status field will show Short and then length shown will be the approximate distance to the fault or short.

Example: Part1-2 Status = Short / Length = 2m

Explanation: A fault or short might occur at about 2m on Part 1-2.

Note: Part 4-5 and Part 7-8 are not used in a 10/100 Mbps environment, so their Status fields will show Open, and the length shown is the approximate length of the attached LAN cable.

Onboard LAN Boot ROM

Allows you to decide whether to activate the boot ROM integrated with the onboard LAN chip. (Default: Disabled)

Onboard IDE Controller (JMicron 368 Chip)

Enables or disables the IDE controller integrated in the JMicron 368 chip. (Default: Enabled)

Onboard Serial Port 1

Enables or disables the first serial port and specifies its base I/O address and corresponding interrupt. Options are: Auto, 3F8/IRQ4 (default), 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3, Disabled.

Onboard Parallel Port

Enables or disables the onboard parallel port (LPT) and specifies its base I/O address and corresponding interrupt. Options are: 378/IRQ7 (default), 278/IRQ5, 3BC/IRQ7, Disabled.

Parallel Port Mode

Selects an operating mode for the onboard parallel (LPT) port. Options are: SPP (Standard Parallel Port)(default), EPP (Enhanced Parallel Port), ECP (Extended Capabilities Port), ECP+EPP.

GA-EP45-UD3LR/UD3L Motherboard

- 52 -

Image 52

Contents GA-EP45-UD3LR/ GA-EP45-UD3L Motherboard Copyright DisclaimerDocumentation Classifications Identifying Your Motherboard RevisionTable of Contents Drivers Installation Box Contents GA-EP45-UD3LR/GA-EP45-UD3L Motherboard Layout Block Diagram Hardware Installation Installation PrecautionsProduct Specifications CPUPage Bios Installing the CPU and CPU Cooler Installing the CPUCPU Socket Lever Installing the CPU Cooler Installing the Memory Dual Channel Memory ConfigurationInstalling a Memory Installing an Expansion Card Back Panel Connectors Center/Subwoofer Speaker Out Jack Orange Rear Speaker Out Jack BlackSide Speaker Out Jack Gray Line In Jack BlueInternal Connectors SATA20/1/2/3/4/5GND FDD Floppy Disk Drive Connector 5 CPUFAN/SYSFAN1/SYSFAN2/PWRFAN Fan HeadersIDE IDE Connector SATA20/1/2/3/4/5 Sata 3Gb/s ConnectorsPwrled System Power LED Header Faudio Front Panel Audio Header PW Power Switch, Red Fpanel Front Panel HeaderCdin CD In Connector, Black Spdifi S/PDIF In Header, RedSpdifo S/PDIF Out Header FUSB1/FUSB2 USB Headers, YellowLPT Parallel Port Header Coma Serial Port Header, WhiteCI Chassis Intrusion Header Clrcmos Clearing Cmos JumperBAT Battery Bios Setup Logo Screen Default Post Screen Startup ScreenFunction Keys End Q-FLASHSample Bios Version GA-EP45-UD3L E19 Bios Setup Program Function KeysMain Menu Main Menu Help Standard Cmos Features  Advanced Bios Features Power Management Setup  PnP/PCI ConfigurationsMB Intelligent TweakerM.I.T SPDRobust Graphics Booster CPU Clock Ratio NoteFine CPU Clock Ratio Note CPU FrequencyCPU Host Frequency Mhz PCI Express Frequency MhzA.2 Advanced Clok ControlCPU Clock Drive PCI Express Clock DriveCPU Clock Skew MCH Clock SkewCommand RateCMD CAS Latency TimeTRCD TRPChannel A/B Timing Settings TRD Phase0 AdjustmentTRD Phase1 Adjustment TRD Phase2 AdjustmentChannel A/B Driving Settings DDR Write TrainingDriving Strength Profile Data Driving Pull-Up LevelLoad-Line Calibration CPU VcoreCPU Termination CPU ReferenceTime DateIDE Channel 0, 1 Master/Slave Floppy 3 Mode Support IDE Channel 2, 3 Master, IDE Channel 4 Master/SlaveDrive a Halt OnHard Disk Boot Priority First/Second/Third Boot DevicePassword Check HDD S.M.A.R.T. CapabilityCPU Multi-Threading Note Limit Cpuid Max. to 3 NoteNo-Execute Memory Protect Note CPU Enhanced Halt C1ENoteFull Screen Logo Show Delay For HDD SecsInit Display First Integrated Peripherals Smart LAN LAN Cable Diagnostic Function USB ControllerUSB 2.0 Controller USB Keyboard SupportOnboard LAN Boot ROM Parallel Port ModeOnboard IDE Controller JMicron 368 Chip Onboard Serial PortSoft-Off by PWR-BTTN Power On by RingPME Event Wake Up Resume by Alarm Hpet Mode NotePower On By Mouse Power On By KeyboardPCI1 IRQ Assignment PnP/PCI ConfigurationsPCI2 IRQ Assignment Reset Case Open Status Current System/CPU TemperatureCurrent CPU/SYSTEM/POWER FAN Speed RPM CPU Warning TemperatureCPU Smart FAN Mode CPU Smart FAN ControlLoad Fail-Safe Defaults Load Optimized DefaultsSupervisor Password User PasswordSave & Exit Setup Exit Without SavingDrivers Installation Installing Chipset DriversApplication Software Technical ManualsContact SystemDownload Center Before You Begin Xpress Recovery2System Requirements Installation and Configuration Installing Windows XP and Partitioning the Hard DrivePage Accessing Xpress Recovery2 Using the Backup Function in Xpress Recovery2Removing the Backup Using the Restore Function in Xpress Recovery2Exiting Xpress Recovery2 Bios Update Utilities Updating the Bios with the Q-Flash UtilityWhat is DualBIOSTM? What is Q-FlashTM?Updating the Bios Load Optimized DefaultsSaveY/N?& ExitY Setup Updating the Bios with the @BIOS Utility Using @BIOSAfter Updating the Bios Update the Bios Using the Internet Update FunctionEasyTune EasyTune 6 Interface Tabs InformationMeter Mode Button Information Table Dynamic Energy Saver Advanced Interface Meter ModeDynamic Energy Saver Advanced Total Mode Button Information Table Total ModeStealth Mode Share Directions for using Q-ShareOptions Descriptions Time Repair System RestorePreference Screen Configuring Sata Hard Drives Configuring the Onboard Sata ControllerTo configure Sata hard drives, follow the steps below Installing Sata hard drives in your computerConfiguring Sata controller mode in Bios Setup RAIDConfiguring a RAID array in RAID Bios Create RAID VolumeCreate Volume Menu ST3120026AS 3JT329JX 111.8GB Delete RAID Volume Delete Volume MenuRequired for Ahci and RAID Mode Making a Sata RAID/AHCI Driver DiskettePage Installing the Sata RAID/AHCI Driver and Operating System Installing Windows XPENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Installing Windows Vista Page Configuring Audio Input and Output Configuring 2/4/5.1/7.1-Channel AudioConfiguring Speakers High Definition Audio HD AudioActivating an AC97 Front Panel Audio Module Configuring Sound EffectMuting the Back Panel Audio For HD Audio Only Installing the S/PDIF In Cable Installing the S/PDIF In Cable OptionalPdif Pdif Out Configuring S/PDIF outConneting a S/PDIF out Cable Configuring Microphone Recording Select Realtek HD Audio Input in the Mixer device list Recording the Sound Using the Sound RecorderPlaying the Sound Troubleshooting Frequently Asked QuestionsTroubleshooting Procedure StartEND Weee Symbol Statement Regulatory StatementsRegulatory Notices Our Commitment to Preserving the EnvironmentChina Restriction of Hazardous Substances Table GA-EP45-UD3LR/UD3L Motherboard 104 105 Appendix GA-EP45-UD3LR/UD3L Motherboard 106 107 Appendix GA-EP45-UD3LR/UD3L Motherboard 108 109 Appendix GA-EP45-UD3LR/UD3L Motherboard 110 Contact Us  G.B.T. INC USA Mexico Gigabyte Global Service System