Gigabyte GA-8S661FXM-775 user manual Press Y on your keyboard to save and exit

Page 59

6. Press Del to enter BIOS menu after system reboots. When you are in BIOS menu, move to Load Fail-Safe Defaults item and press Enter to load BIOS Fail-Safe Defaults. Normally the system redetects all devices after BIOS has been upgraded. Therefore, we highly recommend reloading the BIOS defaults after BIOS has been upgraded.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features	Select Language
Advanced BIOS Features	Load Fail-Safe Defaults
Integrated Peripherals	Load Optimized Defaults
Power Management Setup Load Fail-Safe Defaults (Y/N)?Set SupervisorY		Password
PnP/PCI Configurations	Set User Password
PC Health Status	Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)	Exit Without Saving
ESC: Quit	F3: Change Language
F8: Dual BIOS/Q-Flash	F10: Save & Exit Setup
	Time, Date, Hard Disk Type...

Press Y on your keyboard to load defaults.

7. Select Save & Exit Setup item to save the settings to CMOS and exit the BIOS menu. System will reboot after you exit the BIOS menu. The procedure is completed.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features	Select Language
Advanced BIOS Features	Load Fail-Safe Defaults
Integrated Peripherals	Load Optimized Defaults
Power Management Setup Save to CMOS and EXIT (Y/N)?Set SupervisorY		Password
PnP/PCI Configurations	Set User Password
PC Health Status	Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)	Exit Without Saving
ESC: Quit	F3: Change Language
F8: Dual BIOS/Q-Flash	F10: Save & Exit Setup
	Time, Date, Hard Disk Type...

Press Y on your keyboard to save and exit.

Part Two:

Updating BIOS with Q-FlashTMUtility on Single-BIOS Motherboards.

This part guides users of single-BIOS motherboards how to update BIOS using the Q-FlashTMutility.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features	Top Performance
Advanced BIOS Features	Load Fail-Safe Defaults
Integrated Peripherals	Load Optimized Defaults
Power Management Setup	Set Supervisor Password
PnP/PCI Configurations	Set User Password
PC Health Status	Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)	Exit Without Saving
ESC: Quit	F3: Change Language
F8: Q-Flash	F10: Save & Exit Setup
	Time, Date, Hard Disk Type...

English

- 59 -

Appendix

Image 59

Contents GA-8S661FXM-775 Motherboard GA-8S661FXM-775 Product Manual Classification CopyrightTable of Contents Drivers Installation GA-8S661FXM-775 GA-8S661FXM-775 Motherboard LayoutBlock Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD Connector IDE1/IDE2 IDE ConnectorFaudio Front Audio Panel Connector SATA0/SATA1 Serial ATA Connector, Controlled by SiS964Surcen Fpanel Front Panel ConnectorSpdifio Spdif In/ Out Cdin CD in ConnectorCI Chassis Intrusion, Case Open 13 F1USB / F2USB Front USB ConnectorsClrcmos Clear Cmos Comb Comb ConnectorPwrled BAT BatteryEnglish English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E3 „ Exit Without Saving „ Set Supervisor Password„ Set User Password „ Save & Exit SetupIDE Channel 0 Master, Slave /IDE Channel 1 Master, Slave TimeMemory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onFirst / Second / Third Boot Device Hard Disk Boot PriorityLimit Cpuid Max. to Boot Up Floppy SeekPassword Check CPU Hyper-ThreadingIntegrated Peripherals Onboard LAN device SiS Serial ATA ModeParallel Port Mode ECP Mode Use DMAModemRingOn IRQ 3-7, 9-15, NMIPower LED in S1 State Power On By KeyboardPower On By Mouse Resume by AlarmPnP/PCI Configurations Current CPU/SYSTEM FAN Speed RPM Current CPU TemperatureCase Opened Current VoltageV Vcore / DDR 2.5V / +3.3V / +12VCAS Latency Setting CPU Smart FAN ModeConfigure Dram Timing CPU Clock Ratio MHz Dram RAS to CAS DelayDram RAS Active Time Dram RAS Precharge TimeTop Performance Set Supervisor/User Password Load Optimized DefaultsExit Without Saving Save & Exit SetupBios Setup English Install Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Unique Software UtilityLimitations Main Screen of Xpress Recovery2Precautions Before You Begin Bios Flash Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Press Y on your keyboard to save and exit English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionConfiguring the SiS RAID Bios Creating RAID Volume Udma RAID0 English Deleting RAID Volume Installing the RAID Drivers 4 2 / 4 / 6 Channel Audio Function Introduction Channel Audio SetupChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Jack-Sensing Introuction Introduction of audio connectorsManual setting AMI Bios Beep Codes TroubleshootingEnglish English English English English English English Taiwan Headquarters Contact UsChina Shanghai