Gigabyte GA-8S661FXM-775 Drive a / Drive B, Floppy 3 Mode Support for Japan Area, Halt on, Memory

Page 33

Drive A / Drive B

The category identifies the types of floppy disk drive A or drive B that has been installed in the computer.

None

No floppy drive installed

360K, 5.25"

5.25 inch PC-type standard drive; 360K byte capacity.

1.2M, 5.25"

5.25 inch AT-type high-density drive; 1.2M byte capacity

 

(3.5 inch when 3 Mode is Enabled).

720K, 3.5"

3.5 inch double-sided drive; 720K byte capacity

1.44M, 3.5"

3.5

inch double-sided drive; 1.44M byte capacity. (Default value)

2.88M, 3.5"

3.5

inch double-sided drive; 2.88M byte capacity.

Floppy 3 Mode Support (for Japan Area)

Disabled

Normal Floppy Drive. (Default value)

Drive A

Drive A is 3 mode Floppy Drive.

Drive B

Drive B is 3 mode Floppy Drive.

Both

Drive A & B are 3 mode Floppy Drives.

Halt on

The category determines whether the computer will stop if an error is detected during power-up.

No Errors

The system boot will not stop for any error that may be detected and you

 

will be prompted.

All Errors

Whenever the BIOS detects a non-fatal error the system will be stopped.

All, But Keyboard

The system boot will not stop for a keyboard error; it will stop for all other

 

errors. (Default value)

All, But Diskette

The system boot will not stop for a disk error; it will stop for all other errors.

All, But Disk/Key

The system boot will not stop for a keyboard or disk error; it will stop for all

 

other errors.

Memory

The category is display-only and is determined by POST (Power On Self Test) of the BIOS.

Base Memory

The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system.

The value of the base memory is typically 512K for systems with 512K memory installed on

the motherboard, or 640K for systems with 640K or more memory installed on the motherboard.

Extended Memory

The BIOS determines how much extended memory is present during the POST.

This is the amount of memory located above 1 MB in the CPU's memory address map.

Total Memory

This item displays the memory size that used.

English

- 33 -

BIOS Setup

Image 33
Contents GA-8S661FXM-775 Motherboard GA-8S661FXM-775 Product Manual Classification CopyrightTable of Contents Drivers Installation GA-8S661FXM-775 GA-8S661FXM-775 Motherboard LayoutBlock Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD Connector IDE1/IDE2 IDE ConnectorFaudio Front Audio Panel Connector SATA0/SATA1 Serial ATA Connector, Controlled by SiS964Surcen Fpanel Front Panel ConnectorSpdifio Spdif In/ Out Cdin CD in ConnectorCI Chassis Intrusion, Case Open 13 F1USB / F2USB Front USB ConnectorsClrcmos Clear Cmos Comb Comb ConnectorPwrled BAT BatteryEnglish English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E3 „ Set User Password „ Set Supervisor Password„ Save & Exit Setup „ Exit Without SavingIDE Channel 0 Master, Slave /IDE Channel 1 Master, Slave TimeDrive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on MemoryFirst / Second / Third Boot Device Hard Disk Boot PriorityPassword Check Boot Up Floppy SeekCPU Hyper-Threading Limit Cpuid Max. toIntegrated Peripherals Parallel Port Mode SiS Serial ATA ModeECP Mode Use DMA Onboard LAN deviceModemRingOn IRQ 3-7, 9-15, NMIPower On By Mouse Power On By KeyboardResume by Alarm Power LED in S1 StatePnP/PCI Configurations Case Opened Current CPU TemperatureCurrent VoltageV Vcore / DDR 2.5V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPMCPU Smart FAN Mode Configure Dram TimingCAS Latency Setting Dram RAS Active Time Dram RAS to CAS DelayDram RAS Precharge Time CPU Clock Ratio MHzTop Performance Set Supervisor/User Password Load Optimized DefaultsExit Without Saving Save & Exit SetupBios Setup English Install Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish How to use the Xpress Recovery2 Xpress Recovery2 IntroductionUnique Software Utility System requirementsMain Screen of Xpress Recovery2 PrecautionsLimitations Bios Flash Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Press Y on your keyboard to save and exit English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionConfiguring the SiS RAID Bios Creating RAID Volume Udma RAID0 English Deleting RAID Volume Installing the RAID Drivers 4 2 / 4 / 6 Channel Audio Function Introduction Channel Audio SetupChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Jack-Sensing Introuction Introduction of audio connectorsManual setting AMI Bios Beep Codes TroubleshootingEnglish English English English English English English Taiwan Headquarters Contact UsChina Shanghai