Gigabyte GA-8S661FXM-775 user manual Integrated Peripherals

Page 36

English

2-3	Integrated Peripherals

		CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
				Integrated Peripherals
	IDE1 Conductor Cable			[Auto]		Item Help
	IDE2 Conductor Cable			[Auto]		Menu Level `
	On-Chip Primary PCI IDE			[Enabled]
	On-Chip Secondary PCI IDE			[Enabled]		[Auto]
	AC97 Audio			[Enabled]		Auto-detect IDE
	Onboard LAN device			[Enabled]		cable type
	USB Controller			[Enabled]
	USB Legacy Support			[Disabled]		[ATA 66/100/133]
	SiS Serial ATA Controller			[Enabled]		Set Conductor Cable
	SiS Serial ATA Mode			[RAID]		to ATA66/100/133 (80
	Onboard Serial Port 1			[3F8/IRQ4]		Pins)
	Onboard Serial Port 2			[2F8/IRQ3]
	Onboard Parallel Port			[378/IRQ7]		[Disabled]
	Parallel Port Mode			[ECP]		Set Conductor Cable
	ECP Mode Use DMA			3		ATA33 (40 Pins)
KLJI: Move		Enter: Select		+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
	F5: Previous Values			F6: Fail-Safe Defaults		F7: Optimized Defaults

	IDE1 Conductor Cable
	Auto		BIOS autodetects IDE1 conductor cable .(Default Value)
	ATA66/100/133		Set IDE1 Conductor Cable to ATA66/100/133 (Please make sure your
			IDE device and cable are compatible with ATA66/100/133).
	ATA33		Set IDE1 Conductor Cable to ATA33. (Please make sure your IDE
			device and cable are compatible with ATA33)
	IDE2 Conductor Cable
	Auto		BIOS autodetects IDE2 conductor cable. (Default Value)
	ATA66/100/133		Set IDE2 Conductor Cable to ATA66/100/133. (Please make sure your
			IDE device and cable are compatible with ATA66/100/133)
	ATA33		Set IDE2 Conductor Cable to ATA33. (Please make sure your IDE
			device and cable are compatible with ATA33)
	On-Chip Primary PCI IDE
	Enabled		Enable onboard 1st channel IDE port. (Default value)
	Disabled		Disable onboard 1st channel IDE port.
	On-Chip Secondary PCI IDE
	Enabled		Enable onboard 2nd channel IDE port. (Default value)
	Disabled		Disable onboard 2nd channel IDE port.
	AC97 Audio
	Enabled		Autodetect AC97 audio function. (Default value)
	Disabled		Disable AC97 audio function.

GA-8S661FXM-775 Motherboard

- 36 -

Image 36

Contents GA-8S661FXM-775 Motherboard GA-8S661FXM-775 Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-8S661FXM-775 Motherboard Layout GA-8S661FXM-775Block Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector IDE1/IDE2 IDE Connector FDD FDD ConnectorSATA0/SATA1 Serial ATA Connector, Controlled by SiS964 Faudio Front Audio Panel ConnectorFpanel Front Panel Connector SurcenCdin CD in Connector Spdifio Spdif In/ Out13 F1USB / F2USB Front USB Connectors CI Chassis Intrusion, Case OpenComb Comb Connector Clrcmos Clear CmosBAT Battery PwrledEnglish English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E3 „ Set Supervisor Password „ Set User Password„ Save & Exit Setup „ Exit Without SavingTime IDE Channel 0 Master, Slave /IDE Channel 1 Master, Slave Floppy 3 Mode Support for Japan Area Drive a / Drive B Halt on MemoryHard Disk Boot Priority First / Second / Third Boot DeviceBoot Up Floppy Seek Password CheckCPU Hyper-Threading Limit Cpuid Max. toIntegrated Peripherals SiS Serial ATA Mode Parallel Port ModeECP Mode Use DMA Onboard LAN deviceIRQ 3-7, 9-15, NMI ModemRingOnPower On By Keyboard Power On By MouseResume by Alarm Power LED in S1 StatePnP/PCI Configurations Current CPU Temperature Case OpenedCurrent VoltageV Vcore / DDR 2.5V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPMCPU Smart FAN Mode Configure Dram TimingCAS Latency Setting Dram RAS to CAS Delay Dram RAS Active TimeDram RAS Precharge Time CPU Clock Ratio MHzTop Performance Load Optimized Defaults Set Supervisor/User PasswordSave & Exit Setup Exit Without SavingBios Setup English Drivers Installation Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Xpress Recovery2 Introduction How to use the Xpress Recovery2Unique Software Utility System requirementsMain Screen of Xpress Recovery2 PrecautionsLimitations Bios Flash Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the SiS RAID Bios Creating RAID Volume Udma RAID0 English Deleting RAID Volume Installing the RAID Drivers Channel Audio Setup 4 2 / 4 / 6 Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Introduction of audio connectors Jack-Sensing IntrouctionManual setting Troubleshooting AMI Bios Beep CodesEnglish English English English English English English Contact Us Taiwan HeadquartersChina Shanghai