Gigabyte GA-K8S760M user manual Congratulation!! You have updated Bios successfully

Page 75

Q-Flash Utility V1.30

Flash Type/Size................SST 49LF002A				256K

		CHECKSUM = AC03
		Are you sure to update BIOS?
	[Enter] to continue updating BIOS or "ESC" to abort.



	Enter: Run	/ : Move	ESC: Reset	F10:Power Off

You can press "Enter" to continue updating BIOS or "ESC" to abort.

English

3.Press Y button if you make sure to update BIOS.

Then it will begin to update BIOS. The progress of updating will be shown at the same time.

The porcess of updating BIOS

Q-Flash Utility V1.30

Flash Type/Size................SST 49LF002A256K

Updating BIOS Now...

>>>>>>>>>>>>>.................

Don't Turn Off Power On RESET System

Enter: Run

/ : Move

ESC: Reset

F10:Power Off

Do not turning off power or reset your system at this stage!!

4. Press any keys to return to the Q-FlashTMmenu when the BIOS updating procedure is completed.

Q-Flash Utility V1.30

Flash Type/Size		SST 49LF002A		256K

		!! Copy BIOS completed - pass !!
		Please press any key to continue		....



	Enter: Run	/ : Move	ESC: Reset	F10:Power Off

5. Press Esc and then Enter to exit the Q-FlashTMutility. System will restart.

Q-Flash Utility V1.30

Flash Type/Size		SST 49LF002A		256K

		Are you sure to RESET?
		[Enter] to continue or [Esc] to abort		....



	Enter: Run	/ : Move	ESC: Reset	F10:Power Off

6.Press Del to enter BIOS menu after system reboots and load BIOS Fail-Safe Defaults. See how to load BIOS Fail-Safe Defaults, please kindly refer to Step 6 to 7 in Part One.

Congratulation!! You have updated BIOS successfully!!

- 75 -

Technical Reference

Image 75

Contents GA-K8S760M Mother Board Motherboard GA-K8S760M Read Me First Prepare your computer Installing the motherboard to the chassisTable of Contents Table of Content Chapter Introduction Features SummaryALC655 Codec GA-K8S760M GA-K8S760M Motherboard LayoutAMD Block DiagramGA-K8S760M Motherboard Step Hardware Installation ProcessSocket Actuation Lever Install the Central Processing Unit CPUAngling Rod to 65Connecting the Fan Power Wires DDR Install Memory ModulesDDR Introduction Install Expansion Cards Install I/O Peripherals Cables PS/2 Keyboard and PS/2 Mouse ConnectorParallel Port, Serial Port and VGA Port LPT/COMA/VGA \ Audio Connectors USB/LAN ConnectorConnectors Introduction ATX ATX Power Connector ATX12V +12V Power ConnectorSysfan System Fan Connector Cpufan CPU Fan ConnectorIDE1 / IDE2 IDE1 / IDE2 Connector FDD Floppy ConnectorPwrled SATA0 / SATA1 Serial ATA ConnectorFpanel 2 x 10 pins Connector Faudio Front Audio Connector BAT BatterySpdifio Spdif In / Out Connector Surcen Surround Center ConnectorAuxin AUX In Connector Cdin CD In Connector17 F11394 / F21394 IEEE1394 Connector FUSB1 / FUSB2 Front USB ConnectorGame Game Connector Comb COM B ConnectorWhiteInfolink 20 IRClrcmos Clear Cmos English Bios Setup Advanced Bios Features Main Menu For example Bios Ver. F1zStatus Page Setup Menu / Option Page Setup Menu Standard Cmos FeaturesLoadOptimizedDefaults PowerManagement SetupPnP/PCI Configurations Load Fail-SafeDefaultsDate Standard Cmos FeaturesTime IDE Primary Master, Slave / IDE Secondary Master, SlaveDrive a / Drive B Base Memory Floppy 3 Mode Support forJapanAreaHalton MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password Check FlexibleAGPInitDisplay First On-ChipPrimaryPCIIDE Integrated PeripheralsUSB Controller IDEDMAtransfter accessOn-ChipSecondaryPCIIDE AC97 AudioOnboard Serial Port SiS Serial ATA ModeOnboardLANBootROM Uart Mode SelectGame PortAddress Parallel Port ModeOnboard Parallel port ECPModeUseDMAPower Management Setup Acpi SuspendTypeSoft-Off by Pwrbttn Modem Ring On PowerOnbyKeyboardSystem After AC Back IRQ 3-7, 9-15,NMIResume byAlarm Power On by MousePCI 3 IRQ Assignment PnP/PCI ConfigurationsPCI 1 IRQ Assignment PCI 2 IRQ AssignmentCurrent VoltageV Vcore / DDR25 / +3.3V / +12V Current Thermistor TemperatureCPU Warning Temperature PC Health StatusSystem FAN Fail Warning CPU FAN Fail WarningAGPVoltage Control Frequency/Voltage ControlCPU Clock CPU Voltage ControlDDR Voltage Control Top Performance Load Fail-Safe Defaults Y/N ? N Load Fail-Safe DefaultsLoad Optimized Defaults Y/N ? N Load Optimized DefaultsEnter Password Set Supervisor/User PasswordSave to Cmos and Exit Y/N ? Y Save & Exit SetupQuit Without Saving Y/N ? N Exit Without SavingTechnical Reference @BIOSTM IntroductionEasyTuneTM 4 Introduction Method 1 Q-FlashTMUtility Flash Bios Method IntroductionEntering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screen Steps Task menu for Dual Bios utilityTask menu for Q-FlashTMutility Action barBios file in the floppy disk You can press Enter to continue Please press any key to continue Bios file becomes F12 after updating Press Y on your keyboard to load defaults Entering the Q-FlashTMutility English Do not turning power or reset your system at this stage Congratulation!! You have updated Bios successfully Method 2 @BIOS Utility English 6-Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Introduction of audio connectors Jack-Sensing IntroductionAuto-detecting Manual setting F9 For Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery? How to use the Xpress RecoveryText Mode Exit and Restart Disk Status Serial ATA RAID Bios Utility Operation IntroductionCreating a RAID 0 Array RAID SetupUdma RAID Creating a RAID 1 Array Press 3 and Enter to select RAID RAID 1 Disk Creating a Jbod Array Udma Jbod Appendix Install DriversItem Description Software Application Software Information EasyTune 4 Utilities Installation FAQ Jami Bios Beep Codes GA-K8S760M Motherboard 104 Troubleshooting GA-K8S760M Motherboard 106 Technical Support/RMA Sheet Acronyms Ioapic GA-K8S760M Motherboard 110 111 Appendix GA-K8S760M Motherboard 112