Gigabyte GA-8VM800M-775 user manual Drivers Installation, Install Chipset Drivers

Page 49

Chapter 3Drivers Installation

Pictures below are shown in Windows XP.

Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driver CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device icon in "My computer", and execute the Setup.exe.

3-1 Install Chipset Drivers

After insert the driver CD, "Xpress Install" will scan automatically the system and then list all the drivers that recommended to install. The "Xpress Install" uses the"Click and Go" technology to install the drivers automatically. Just select the drivers you want then click the "GO" button. The "Xpress Install" will execute the installation for you automatically.

Some device drivers will restart your system automatically. After restarting your system the "Xpress Install" will continue to install other drivers.

System will reboot automatically after install the drivers, afterward you can install others application.

1. For USB2.0 driver support under Windows XP operating system, please use Windows Service Pack. After install Windows Service Pack, it will show a question mark "?" in "Universal Serial Bus controller" under "Device Manager". Please remove the question mark and restart the system (System will auto-detect the right USB2.0 driver).

2. Some Nvidia graphics cards might have display problems under Windows 2000/XP. Please install the driver from the following location: D:\Chipset\nVidia\WinXP_2K\Setup.exe (we assume your CD-ROM drive is D:).

English

- 49 -

Drivers Installation

Image 49
Contents GA-8VM800M-775 Motherboard GA-8VM800M-775 Product Manual Classification CopyrightTable of Contents Drivers Installation GA-8VM800M-775 Motherboard Layout Block Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0/SATA1 Serial ATA Connector IDE1/IDE2 IDE ConnectorFpanel Front Panel Connector Pwrled Faudio Front Audio Panel ConnectorAuxin AUX In Connector Cdin CD in ConnectorSurcen Spdifio Spdif In/ OutComb Comb Connector 15 F1USB / F2USB Front USB ConnectorsClrcmos Clear Cmos CI Chassis Intrusion, Case OpenBAT Battery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E12 „ Set Supervisor Password „ Load Optimized Defaults„ Set User Password „ Save & Exit SetupTime Standard Cmos FeaturesIDE Channel 0/1 Master, Slave IDE Channel 2/3 MasterDrive a Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Password CheckLimit Cpuid Max. to CPU Hyper-ThreadingNo-Execute Memory Protect Note CPU Enhanced Halt C1E NoteRAID Integrated PeripheralsParallel Port Mode OnBoard LAN Boot ROMEPP Mode Select USB Mouse SupportAcpi OS Power Management SetupResume by Alarm Mouse Power OnPME Event Wake Up Modem Ring ResumePCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status Frequency / Voltage Control CPU Clock CPU Host Clock ControlDram Clock AGP OverVoltage ControlLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish English Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionHow to use the Xpress Recovery2 Xpress Recovery2 IntroductionSystem requirements Precautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the VT8237VT8237R Sata RAID Bios Setup Utility Configuring the VT8237VT8237R Sata RAID BiosCreate Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Cd bootdrv Menu Installing the RAID drivers5 2 / 4 / 6 Channel Audio Function Introduction Channel Audio SetupChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device AMI Bios Beep Codes TroubleshootingEnglish English English English English English English Taiwan Headquarters Contact UsChina Shanghai