Gigabyte GA-8VM800M-775 CPU Host Clock Control, CPU Clock, Dram Clock, AGP OverVoltage Control

Page 43

CPU Host Clock Control

Note: Please note that if your system is overclocked and cannot restart, please wait 20secs. for automatic system restart or clear the CMOS setup data and perform a safe restart.

Disabled

Disable CPU Host Clock Control. (Default value)

Enabled

Enable CPU Host Clock Control.

CPU Clock

200MHz ~255MHz Set CPU Clock from 200MHz to 255MHz.

DRAM Clock

Please set DRAM Clock according to your requirement.

If you use DDR266 DRAM module, please set "DRAM Clock" to "133". If you use DDR333 DRAM module, please set "DRAM Clock" to "166". If you use DDR400 DRAM module, please set "DRAM Clock" to "200".

Incorrect using it may cause your system broken. For power End-User use only!

AGP OverVoltage Control

Auto

BIOS will automatically detect AGP voltage. (Default value)

+0.1V

Set AGP OverVoltage Control to +0.1V.

+0.2V

Set AGP OverVoltage Control to +0.2V.

Increase AGP voltage may get stable for Over_Clock. But it may damage to AGP Card when enable this feature.

DIMM OverVoltage Control

Please note that by overclocking your system through the increase of the DDR voltage, damage to the memory may occur.

Auto

BIOS will automatically detect DIMM voltage. (Default value)

+0.1V

Set DIMM OverVoltage Control to +0.1V.

+0.2V

Set DIMM OverVoltage Control to +0.2V.

Incorrect using it may cause your system broken. For power End-User use only!

English

- 43 -

BIOS Setup

Image 43
Contents GA-8VM800M-775 Motherboard GA-8VM800M-775 Product Manual Classification CopyrightTable of Contents Drivers Installation GA-8VM800M-775 Motherboard Layout Block Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0/SATA1 Serial ATA Connector IDE1/IDE2 IDE ConnectorFpanel Front Panel Connector Pwrled Faudio Front Audio Panel ConnectorAuxin AUX In Connector Cdin CD in ConnectorSurcen Spdifio Spdif In/ OutComb Comb Connector 15 F1USB / F2USB Front USB ConnectorsClrcmos Clear Cmos CI Chassis Intrusion, Case OpenBAT Battery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E12 „ Save & Exit Setup „ Load Optimized Defaults„ Set Supervisor Password „ Set User PasswordIDE Channel 2/3 Master Standard Cmos FeaturesTime IDE Channel 0/1 Master, SlaveMemory Floppy 3 Mode Support for Japan AreaDrive a Halt onPassword Check Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceCPU Enhanced Halt C1E Note CPU Hyper-ThreadingLimit Cpuid Max. to No-Execute Memory Protect NoteRAID Integrated PeripheralsUSB Mouse Support OnBoard LAN Boot ROMParallel Port Mode EPP Mode SelectAcpi OS Power Management SetupModem Ring Resume Mouse Power OnResume by Alarm PME Event Wake UpPCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status Frequency / Voltage Control AGP OverVoltage Control CPU Host Clock ControlCPU Clock Dram ClockLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish English Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionHow to use the Xpress Recovery2 Xpress Recovery2 IntroductionSystem requirements Precautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the VT8237VT8237R Sata RAID Bios Setup Utility Configuring the VT8237VT8237R Sata RAID BiosCreate Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Cd bootdrv Menu Installing the RAID drivers5 2 / 4 / 6 Channel Audio Function Introduction Channel Audio SetupChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device AMI Bios Beep Codes TroubleshootingEnglish English English English English English English Taiwan Headquarters Contact UsChina Shanghai