Gigabyte GA-8I915ME Series user manual IDE IDE Connector

Page 24

English

6)IDE (IDE Connector)

An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other as Slave (for information on settings, please refer to the instructions located on the IDE device).

4039

21

7)SATA0/SATA2 (Serial ATA Connector, Controlled by ICH6)

Serial ATA can provide up to 150MB/s transfer rate. Please refer to the BIOS setting for the Serial ATA and install the proper driver in order to work properly.

 

 

Pin No.

Definition

1

7

1

GND

2

TXP

 

 

 

 

3

TXN

 

 

4

GND

 

 

5

RXN

 

 

6

RXP

 

 

7

GND

GA-8I915ME Series Motherboard

- 24 -

Image 24
Contents GA-8I915ME Series Motherboard Copyright Product Manual ClassificationTable of Content Install Drivers GA-8I915ME Series Motherboard Layout GA-8I915MEBlock Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory English Installation of Expansion Cards What is G.E.A.R.? Graphics Card Support ListAsus Asus AX800XT AX700PRO MSI I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorIDE IDE Connector SATA0/SATA2 Serial ATA Connector, Controlled by ICH6Fpanel Front Panel Jumper WOL Wake On LANFaudio Front Audio Connector PwrledAuxin AUX In Connector Cdin CDUSB1 / FUSB2 Front USB Connector 15 COM2 Serial Port ConnectorSurcen Spdifio Spdif In/ OutCI Chassis Intrusion, Case Open Clrcmos Clear CmosBioswp Bios Write Protect BATBatteryEnglish Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example GA-8I915ME-GV / Bios Ver. F2 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupStandard Cmos Features DateTime IDE Channel 0~2 Master, SlaveFloppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryHard Disk Boot Priority First / Second / Third Boot DevicePassword Check CPU Hyper-Threading Limit Cpuid Max. toInit Display First Note1 No-Execute Memory Protect Note3Integrated Peripherals Onboard LAN Boot ROM Parallel Port ModeECP Mode Use DMA USB Keyboard SupportPower Management Setup Power On By Keyboard KB Power on PasswordAC Back Function PnP/PCI Configurations Reset Case Open Status Current CPU TemperatureCPU Warning Temperature CPU Smart FAN ModeCPU Clock Ratio Note Memory Frequency forMemory Frequency Mhz Load Fail-Safe Defaults Set Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Install Drivers Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewXpress Recovery2 Introduction How to use the Xpress Recovery2System requirements Main Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Channel Audio Setup 4 2 / 4 / 6 Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Introduction of audio connectors Jack-Sensing IntrouctionManual setting Troubleshooting English English Contact Us Taiwan HeadquartersChina Shanghai