Gigabyte GA-8I915ME Series user manual Hard Disk Boot Priority, First / Second / Third Boot Device

Page 38

English

2-2

Advanced BIOS Features

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

 

 

 

 

Advanced BIOS Features

 

 

`

Hard Disk Boot Priority

[Press Enter]

Item Help

 

First Boot Device

[Floppy]

 

Menu Level`

 

Second Boot Device

[USB-FDD]

 

 

 

Third Boot Device

[Hard Disk]

Select Hard Disk Boot

 

Password Check

[Setup]

 

Device Priority

#

CPU Hyper-Threading

[Enabled]

 

 

 

 

Limit CPUID Max. to 3

[Disabled]

 

 

 

 

Init Display First (Note1)

[PCI]

 

 

 

 

No-Execute Memory Protect (Note3)

[Enabled]

 

 

 

 

CPU Enhanced Halt (C1E) (Note3)

[Enabled]

 

 

 

 

CPU Thermal Monitor 2(TM2) (Note3)

[Enabled]

 

 

 

 

CPU EIST Function (Note3)

[Enabled]

 

 

 

 

On-Chip Frame Buffer Size

[4MB]

 

 

 

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F5: Previous Values

F6: Fail-Save Default

 

F7: Optimized Defaults

 

 

 

 

 

 

 

" # " System will detect automatically and show up when you install the Intel® Pentium® 4 processor with HT Technology.

Hard Disk Boot Priority

Select boot sequence for onboard(or add-on cards) SCSI, RAID, etc.

Use <> or < > to select a device, then press<+> to move it up, or <-> to move it down the list. Press <ESC> to exit this menu.

First / Second / Third Boot Device

Floppy

Select your boot device priority by Floppy.

LS120

Select your boot device priority by LS120.

Hard Disk

Select your boot device priority by Hard Disk.

CDROM

Select your boot device priority by CDROM.

ZIP

Select your boot device priority by ZIP.

USB-FDD

Select your boot device priority by USB-FDD.

USB-ZIP

Select your boot device priority by USB-ZIP.

USB-CDROM

Select your boot device priority by USB-CDROM.

USB-HDD

Select your boot device priority by USB-HDD.

LAN

Select your boot device priority by LAN.

Disabled

Disabled this function.

Password Check

Setup

The system will boot but will not access to Setup page if the correct

 

password is not entered at the prompt. (Default value)

System

The system will not boot and will not access to Setup page if the correct

 

password is not entered at the prompt.

(Note3) This item will show up when you install a processor which supports this function.

GA-8I915ME Series Motherboard

- 38 -

Image 38
Contents GA-8I915ME Series Motherboard Copyright Product Manual ClassificationTable of Content Install Drivers GA-8I915ME Series Motherboard Layout GA-8I915MEBlock Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory English Installation of Expansion Cards What is G.E.A.R.? Graphics Card Support ListAsus Asus AX800XT AX700PRO MSI I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorIDE IDE Connector SATA0/SATA2 Serial ATA Connector, Controlled by ICH6Fpanel Front Panel Jumper WOL Wake On LANFaudio Front Audio Connector PwrledAuxin AUX In Connector Cdin CDUSB1 / FUSB2 Front USB Connector 15 COM2 Serial Port ConnectorSurcen Spdifio Spdif In/ OutCI Chassis Intrusion, Case Open Clrcmos Clear CmosBioswp Bios Write Protect BATBatteryEnglish Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example GA-8I915ME-GV / Bios Ver. F2 „ Set User Password „ Load Optimized Defaults „ Set Supervisor Password „ Save & Exit SetupTime Standard Cmos FeaturesDate IDE Channel 0~2 Master, SlaveHalt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryPassword Check Hard Disk Boot PriorityFirst / Second / Third Boot Device Init Display First Note1 CPU Hyper-ThreadingLimit Cpuid Max. to No-Execute Memory Protect Note3Integrated Peripherals ECP Mode Use DMA Onboard LAN Boot ROMParallel Port Mode USB Keyboard SupportPower Management Setup AC Back Function Power On By KeyboardKB Power on Password PnP/PCI Configurations CPU Warning Temperature Reset Case Open StatusCurrent CPU Temperature CPU Smart FAN ModeMemory Frequency Mhz CPU Clock Ratio NoteMemory Frequency for Load Fail-Safe Defaults Set Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Install Drivers Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewSystem requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Limitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Channel Audio Setup 4 2 / 4 / 6 Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Introduction of audio connectors Jack-Sensing IntrouctionManual setting Troubleshooting English English Contact Us Taiwan HeadquartersChina Shanghai