Gigabyte GA-8I915ME Series CPU Clock Ratio Note, Memory Frequency for, Memory Frequency Mhz

Page 46

English

2-7

Frequency/Voltage Control

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

 

 

 

 

Frequency/Voltage Control

 

 

 

CPU Clock Ratio

[16X]

 

 

Item Help

 

Memory Frequency for

[Auto]

 

Menu Level`

 

Memory Frequency (Mhz)

333

 

 

 

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F5: Previous Values

F6: Fail-Save Default

 

F7: Optimized Defaults

 

 

 

 

 

 

 

Incorrect using these features may cause your system broken. For power end-user use only.

CPU Clock Ratio (Note)

This setup option will automatically assign by CPU detection.

The option will display "Locked" and read only if the CPU ratio is not changeable.

Memory Frequency for

Wrong frequency may make system can't boot, clear CMOS to overcome wrong frequency issue. for FSB(Front Side Bus) frequency=533MHz,

2.5

Memory Frequency = Host clock X 2.5.

3

Memory Frequency = Host clock X 3.

4

Memory Frequency = Host clock X 4.

Auto

Set Memory frequency by DRAM SPD data. (Default value)

for FSB(Front Side Bus) frequency=800MHz,

1.66

Memory Frequency = Host clock X 1.66.

2.00

Memory Frequency = Host clock X 2.00.

2.66

Memory Frequency = Host clock X 2.66.

Auto

Set Memory frequency by DRAM SPD data. (Default value)

Memory Frequency (Mhz)

The values depend on "System Memory Multiplier" item.

(Note) This item will show up when you install a processor which supports this function.

GA-8I915ME Series Motherboard

- 46 -

Image 46
Contents GA-8I915ME Series Motherboard Copyright Product Manual ClassificationTable of Content Install Drivers GA-8I915ME Series Motherboard Layout GA-8I915MEBlock Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory English Installation of Expansion Cards What is G.E.A.R.? Graphics Card Support ListAsus Asus AX800XT AX700PRO MSI I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorIDE IDE Connector SATA0/SATA2 Serial ATA Connector, Controlled by ICH6Fpanel Front Panel Jumper WOL Wake On LANFaudio Front Audio Connector PwrledAuxin AUX In Connector Cdin CDUSB1 / FUSB2 Front USB Connector 15 COM2 Serial Port ConnectorSurcen Spdifio Spdif In/ OutCI Chassis Intrusion, Case Open Clrcmos Clear CmosBioswp Bios Write Protect BATBatteryEnglish Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example GA-8I915ME-GV / Bios Ver. F2 „ Set User Password „ Load Optimized Defaults„ Set Supervisor Password „ Save & Exit SetupTime Standard Cmos FeaturesDate IDE Channel 0~2 Master, SlaveHalt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Hard Disk Boot PriorityPassword Check Init Display First Note1 CPU Hyper-ThreadingLimit Cpuid Max. to No-Execute Memory Protect Note3Integrated Peripherals ECP Mode Use DMA Onboard LAN Boot ROMParallel Port Mode USB Keyboard SupportPower Management Setup KB Power on Password Power On By KeyboardAC Back Function PnP/PCI Configurations CPU Warning Temperature Reset Case Open StatusCurrent CPU Temperature CPU Smart FAN ModeMemory Frequency for CPU Clock Ratio NoteMemory Frequency Mhz Load Fail-Safe Defaults Set Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Install Drivers Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewHow to use the Xpress Recovery2 Xpress Recovery2 IntroductionSystem requirements Precautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Channel Audio Setup 4 2 / 4 / 6 Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Introduction of audio connectors Jack-Sensing IntrouctionManual setting Troubleshooting English English Contact Us Taiwan HeadquartersChina Shanghai