Gigabyte GA-8I915ME Series user manual Integrated Peripherals

Page 40

English

2-3 Integrated Peripherals

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Integrated Peripherals

On-Chip Primary PCI IDE

[Enabled]

On-Chip SATA Mode

[Enhanced]

x PATA IDE Set to

Ch.0 Master/Slave

SATA Port 0/2 Set to

Ch.2 Master/Slave

USB Controller

[Enabled]

USB 2.0 Controller

[Enabled]

USB Keyboard Support

[Disabled]

USB Mouse Support

[Disabled]

AC97 Audio

[Auto]

Onboard H/W LAN

[Enabled]

Onboard LAN Boot ROM

[Disabled]

Onboard Serial Port 1

[3F8/IRQ4]

Onboard Serial Port 2

[2F8/IRQ3]

Onboard Parallel Port

[378/IRQ7]

Parallel Port Mode

[SPP]

x ECP Mode Use DMA

3

Item Help

Menu Level`

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

F5: Previous Values

F6: Fail-Save Default

 

F7: Optimized Defaults

On-Chip Primary PCI IDE

Enabled

Enable onboard 1st channel IDE port. (Default value)

Disabled

Disable onboard 1st channel IDE port.

On-Chip SATA Mode

Disabled

Disable this function.

Auto

BIOS will auto detect.

Combined

Set On-Chip SATA mode to Combined, you can use up to 4 HDDs on

 

the motherboard; 2 for SATA and the other for PATA IDE.

Enhanced

Set On-Chip SATA mode to Enhanced, the motherboard allows up to 6

 

HDDs to use.(Default value)

Non-Combined

Set On-Chip SATA mode to Non-Combined, SATA will be simulated to

 

PATA mode.

PATA IDE Set to

Ch.1 Master/Slave

Set PATA IDE to Ch. 1 Master/Slave. (Default value)

Ch.0 Master/Slave

Set PATA IDE to Ch. 0 Master/Slave.

SATA Port 0/2 Set to

 

This value will auto make by the setting "On-Chip SATA Mode" and "PATA IDE Set to".

If PATA IDE were set to Ch. 1 Master/Slave, this function will auto set to Ch. 0 Master/Slave.

USB Controller

Enabled

Enable USB Controller. (Default value)

Disabled

Disable USB Controller.

USB 2.0 Controller

Disable this function if you are not using onboard USB 2.0 feature.

Enabled

Enable USB 2.0 Controller. (Default value)

Disabled

Disable USB 2.0 Controller.

GA-8I915ME Series Motherboard

- 40 -

Image 40
Contents GA-8I915ME Series Motherboard Copyright Product Manual ClassificationTable of Content Install Drivers GA-8I915ME Series Motherboard Layout GA-8I915MEBlock Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory English Installation of Expansion Cards What is G.E.A.R.? Graphics Card Support ListAsus Asus AX800XT AX700PRO MSI I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorIDE IDE Connector SATA0/SATA2 Serial ATA Connector, Controlled by ICH6Fpanel Front Panel Jumper WOL Wake On LANFaudio Front Audio Connector PwrledAuxin AUX In Connector Cdin CDUSB1 / FUSB2 Front USB Connector 15 COM2 Serial Port ConnectorSurcen Spdifio Spdif In/ OutCI Chassis Intrusion, Case Open Clrcmos Clear CmosBioswp Bios Write Protect BATBatteryEnglish Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example GA-8I915ME-GV / Bios Ver. F2 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupStandard Cmos Features DateTime IDE Channel 0~2 Master, SlaveFloppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryFirst / Second / Third Boot Device Hard Disk Boot PriorityPassword Check CPU Hyper-Threading Limit Cpuid Max. toInit Display First Note1 No-Execute Memory Protect Note3Integrated Peripherals Onboard LAN Boot ROM Parallel Port ModeECP Mode Use DMA USB Keyboard SupportPower Management Setup KB Power on Password Power On By KeyboardAC Back Function PnP/PCI Configurations Reset Case Open Status Current CPU TemperatureCPU Warning Temperature CPU Smart FAN ModeMemory Frequency for CPU Clock Ratio NoteMemory Frequency Mhz Load Fail-Safe Defaults Set Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Install Drivers Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewHow to use the Xpress Recovery2 Xpress Recovery2 IntroductionSystem requirements Precautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Channel Audio Setup 4 2 / 4 / 6 Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Introduction of audio connectors Jack-Sensing IntrouctionManual setting Troubleshooting English English Contact Us Taiwan HeadquartersChina Shanghai