Gigabyte GA-8AENXP-D CPU Smart FAN Control, CPU Smart FAN Mode, Operate at full speed, Spinning

Page 43

CPU Smart FAN Control

Disabled

Disable this function.

Enabled

Enable the CPU Smart FAN Control function. (Default value)

 

a.

When the CPU temperature is higher than 65 degrees Celsius, CPU fan will

 

 

operate at full speed.

 

b.

When the CPU temperature is between 20 and 65 degrees Celsius, the CPU

 

 

fan speed will change depending on the actual CPU temperature.

 

c.

When the CPU temperature is lower than 20 degrees Celsius, CPU fan will stop

 

 

spinning.

CPU Smart FAN Mode

This option is available only when CPU Smart FAN Control is enabled.

Auto

BIOS autodetects the type of CPU fan you installed and sets the optimal CPU Smart

 

FAN control mode for it. (Default value)

Voltage

Set to Voltage when you use a CPU fan with a 3-pin fan power cable.

PWM

Set to PWM when you use a CPU fan with a 4-pin fan power cable.

In fact, the Voltage option can be used for CPU fans with 3-pin or 4-pin power cables. However, some 4-pin CPU fan power cables are not designed following Intel 4-wire fans PWM control specifications. With such CPU fans, selecting PWM will not effectively reduce the fan speed.

English

- 43 -

BIOS Setup

Image 43
Contents GA-8AENXP-D Motherboard Product Manual Classification CopyrightTable of Contents Unique Software Utilities Drivers InstallationGA-8AENXP-D Motherboard Layout PCI Express Intel 925XE Dual BiosLGA775 Host InterfacePage Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyFeature Summary Supports data transfer rate of up 150 MB Use of licensed Award BiosŠ Supports Dual BIOS/Q-Flash/Multilanguage Bios Supports data striping RAID 0 or mirroring RAID 1 functionInstallation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Installing/Removing Cool-Plus Northbridge Cooling FanDual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Side Speaker Out Connectors IntroductionConnect the Center/Subwoofer speakers to this connector Center/Subwoofer Speaker OutATX12V/ATX Power Connector Nbfan Chip Fan Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power ConnectorIDE IDE Connector FDD FDD ConnectorPwrled Fpanel Front Panel Jumper Cdin CD In Connector Azaliafp Front Audio Panel ConnectorConnect CD-ROM or DVD-ROM audio out to the connector 16 F11394 / F21394 Ieee 1394 Connector USB1 / FUSB2 / FUSB3 / FUSB4 Front USB ConnectorCable, please contact your local dealer Clrcmos Clear Cmos 17 IRCI Chassis Intrusion, Case Open BATBatteryEnglish Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F3d „ Set User Password „ Load Fail-Safe Defaults„ Load Optimized Defaults „ Set Supervisor PasswordIDE Channel 0 Master, Slave TimeDetection step and allow for faster system start up Memory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onFirst / Second / Third Boot Device Hard Disk Boot PriorityNo-Execute Memory ProtectNote Password CheckCPU Hyper-Threading Limit Cpuid Max. toOn-Chip Primary PCI IDE Sata RAID / Ahci ModeOn-Chip Sata Mode Integrated PeripheralsUSB Controller Pata IDE Set toSata Port 0/2 Set to Sata Port 1/3 Set toUR2 Duplex Mode Onboard LAN1 Boot ROM LAN1 portOnboard LAN2 Boot ROM LAN2 port Uart Mode SelectECP Mode Use DMA Parallel Port ModeIf RTC Alarm Lead To Power On is Enabled Resume by AlarmPower On By Mouse Disabled Disable this function. Default value EnabledAC Back Function Power On By KeyboardKB Power on Password Before AC-power offCPU/POWER/SYSTEM FAN Fail Warning Current CPU TemperatureCurrent CPU/POWER/SYSTEM FAN Speed RPM CPU Warning TemperatureOperate at full speed CPU Smart FAN ModeFAN control mode for it. Default value CPU Smart FAN ControlCPU Host Clock Control CPU Clock RatioRobust Graphics Booster A.2Memory Frequency Mhz CPU Host FrequencyMhzPCI Express FrequencyMhz Memory Frequency ForSelect Language Load Fail-Safe DefaultsSet Supervisor/User Password Load Optimized DefaultsExit Without Saving Save & Exit SetupBios Setup English Install Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsPlease see the last page for details Hardware InformationContact Us This page lists all device you have for this motherboardEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionWhat is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery F9 For Xpress Recovery Exit and restart your computer Restores backup image to original stateRemove the backup image Exit and RestartDual Bios / Q-Flash Programming Utility Flash Bios Method IntroductionWhat is Dual Bios Technology? How to use Dual Bios and Q-Flash Utility?Halt On Error DisableDefault, Enable Wide Range Protection DisableDefault, EnableBoot From Main BIOSDefault, Backup Bios Auto Recovery EnableDefault, DisableBefore You Begin Method 1 Q-FlashTMUtilityTask menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two Press Y on your keyboard to load defaultsFlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully @BIOS utility Method 2 @BIOSTM UtilityMethods and steps English RAID Levels Serial ATA Bios Setting Utility IntroductionDISK/VOLUME Information Configuring the Intel RAID BiosPress Enter under Create RAID Volume to set up RAID Create RAID Volume128KB Press Enter under the Create Volume item Delete RAID Volume Installing the RAID drivers Stereo Speakers Connection and Settings Introduction of audio connectors5 2- / 4- / 6- / 8- ChannelAudio Function Introduction Front Speaker Out Rear Speaker Out Channel Audio SetupEnglish Step Jack-Sensing Introduction AMI Bios Beep Codes TroubleshootingEnglish English English Taiwan Headquarters Contact UsChina Shanghai