Gigabyte GA-8AENXP-D LGA775, Host Interface, PCI Express Intel 925XE, PCI Express x 1 Ports, 8001

Page 7

Block Diagram

PCI-ECLK

(100MHz)

LGA775

CPUCLK+/-(266/200/133MHz)

Processor

Host

Interface

DDRII 711/600(Note)/533/400MHz DIMM

PCI Express x16

Intel

925XE

Dual Channel Memory

3 PCI Express x 1 Ports

MCH

MCHCLK (266/200/133MHz)

PCI-ECLK

(100MHz)

66MHz

RJ45

33MHz

14.318MHz

Broadcom

48MHz

5751/5789

Dual BIOS

4 Serial ATA

PCI Express x 1 Bus

Intel

4 Serial ATA

PCI Bus

ICH6R

SiI3114

ATA33/66/100 IDE Channels

Marvell

TSB82AA2

8001

TSB81BA3

Floppy

RJ45

IT 8712

LPT Port

IEEE1394b3

OutSpeaker

MIC Out-Line

In-Line

InSPDIF OutSPDIF

CY7C6564D

CODEC

COM Port

24MHz

PS/2 KB/Mouse

8 USB

2 PCI

Ports

33MHz

Surround Center/Subwoofer Side

3 USB

Ports

PCICLK

(33MHz)

(Note) To use a DDRII 711 memory module on the motherboard, you must install a 1066MHz FSB processor and overclock in BIOS.

To use a DDRII 600 memory module on the motherboard, you must install an 800MHz FSB processor and overclock in BIOS.

- 7 -

Image 7

Contents GA-8AENXP-D Motherboard Product Manual Classification CopyrightTable of Contents Unique Software Utilities Drivers InstallationGA-8AENXP-D Motherboard Layout PCI Express Intel 925XE Dual BiosLGA775 Host InterfacePage Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyFeature Summary Supports data transfer rate of up 150 MB Use of licensed Award BiosŠ Supports Dual BIOS/Q-Flash/Multilanguage Bios Supports data striping RAID 0 or mirroring RAID 1 functionInstallation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Installing/Removing Cool-Plus Northbridge Cooling FanDual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Side Speaker Out Connectors IntroductionConnect the Center/Subwoofer speakers to this connector Center/Subwoofer Speaker OutATX12V/ATX Power Connector Nbfan Chip Fan Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power ConnectorIDE IDE Connector FDD FDD ConnectorPwrled Fpanel Front Panel Jumper Cdin CD In Connector Azaliafp Front Audio Panel ConnectorConnect CD-ROM or DVD-ROM audio out to the connector 16 F11394 / F21394 Ieee 1394 Connector USB1 / FUSB2 / FUSB3 / FUSB4 Front USB ConnectorCable, please contact your local dealer Clrcmos Clear Cmos 17 IRCI Chassis Intrusion, Case Open BATBatteryEnglish Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F3d „ Set User Password „ Load Fail-Safe Defaults„ Load Optimized Defaults „ Set Supervisor PasswordIDE Channel 0 Master, Slave TimeDetection step and allow for faster system start up Memory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onFirst / Second / Third Boot Device Hard Disk Boot PriorityNo-Execute Memory ProtectNote Password CheckCPU Hyper-Threading Limit Cpuid Max. toOn-Chip Primary PCI IDE Sata RAID / Ahci ModeOn-Chip Sata Mode Integrated PeripheralsUSB Controller Pata IDE Set toSata Port 0/2 Set to Sata Port 1/3 Set toUR2 Duplex Mode Onboard LAN1 Boot ROM LAN1 portOnboard LAN2 Boot ROM LAN2 port Uart Mode SelectECP Mode Use DMA Parallel Port ModeIf RTC Alarm Lead To Power On is Enabled Resume by AlarmPower On By Mouse Disabled Disable this function. Default value EnabledAC Back Function Power On By KeyboardKB Power on Password Before AC-power offCPU/POWER/SYSTEM FAN Fail Warning Current CPU TemperatureCurrent CPU/POWER/SYSTEM FAN Speed RPM CPU Warning TemperatureOperate at full speed CPU Smart FAN ModeFAN control mode for it. Default value CPU Smart FAN ControlCPU Host Clock Control CPU Clock RatioRobust Graphics Booster A.2Memory Frequency Mhz CPU Host FrequencyMhzPCI Express FrequencyMhz Memory Frequency ForSelect Language Load Fail-Safe DefaultsSet Supervisor/User Password Load Optimized DefaultsExit Without Saving Save & Exit SetupBios Setup English Install Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsPlease see the last page for details Hardware InformationContact Us This page lists all device you have for this motherboardEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionWhat is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery F9 For Xpress Recovery Exit and restart your computer Restores backup image to original stateRemove the backup image Exit and RestartDual Bios / Q-Flash Programming Utility Flash Bios Method IntroductionWhat is Dual Bios Technology? How to use Dual Bios and Q-Flash Utility?Halt On Error DisableDefault, Enable Wide Range Protection DisableDefault, EnableBoot From Main BIOSDefault, Backup Bios Auto Recovery EnableDefault, DisableBefore You Begin Method 1 Q-FlashTMUtilityTask menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two Press Y on your keyboard to load defaultsFlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully @BIOS utility Method 2 @BIOSTM UtilityMethods and steps English RAID Levels Serial ATA Bios Setting Utility IntroductionDISK/VOLUME Information Configuring the Intel RAID BiosPress Enter under Create RAID Volume to set up RAID Create RAID Volume128KB Press Enter under the Create Volume item Delete RAID Volume Installing the RAID drivers Stereo Speakers Connection and Settings Introduction of audio connectors5 2- / 4- / 6- / 8- ChannelAudio Function Introduction Front Speaker Out Rear Speaker Out Channel Audio SetupEnglish Step Jack-Sensing Introduction AMI Bios Beep Codes TroubleshootingEnglish English English Taiwan Headquarters Contact UsChina Shanghai