Gigabyte GA-8AENXP-D user manual CI Chassis Intrusion, Case Open, BATBattery

Page 27

19)CI (Chassis Intrusion, Case Open)

This 2-pin connector allows your system to enable or disable the "case open" item in BIOS if the system case has been remove.

	Pin No.	Definition
	1	Signal
1	2	GND
1

20) BAT(Battery)

English

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's instructions.

If you want to erase CMOS...

1.Turn OFF the computer and unplug the power cord.

2.Remove the battery, wait for 30 second.

3.Re-install the battery.

4.Plug the power cord and turn ON the computer.

- 27 -

Hardware Installation

Image 27

Contents GA-8AENXP-D Motherboard Product Manual Classification CopyrightTable of Contents Unique Software Utilities Drivers InstallationGA-8AENXP-D Motherboard Layout PCI Express Intel 925XE Dual BiosLGA775 Host InterfacePage Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyFeature Summary Supports data transfer rate of up 150 MB Use of licensed Award BiosŠ Supports Dual BIOS/Q-Flash/Multilanguage Bios Supports data striping RAID 0 or mirroring RAID 1 functionInstallation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Installing/Removing Cool-Plus Northbridge Cooling FanDual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Side Speaker Out Connectors IntroductionConnect the Center/Subwoofer speakers to this connector Center/Subwoofer Speaker OutATX12V/ATX Power Connector Nbfan Chip Fan Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power ConnectorIDE IDE Connector FDD FDD ConnectorPwrled Fpanel Front Panel Jumper Azaliafp Front Audio Panel Connector Cdin CD In ConnectorConnect CD-ROM or DVD-ROM audio out to the connector USB1 / FUSB2 / FUSB3 / FUSB4 Front USB Connector 16 F11394 / F21394 Ieee 1394 ConnectorCable, please contact your local dealer Clrcmos Clear Cmos 17 IRCI Chassis Intrusion, Case Open BATBatteryEnglish Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F3d „ Set User Password „ Load Fail-Safe Defaults„ Load Optimized Defaults „ Set Supervisor PasswordTime IDE Channel 0 Master, SlaveDetection step and allow for faster system start up Memory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onFirst / Second / Third Boot Device Hard Disk Boot PriorityNo-Execute Memory ProtectNote Password CheckCPU Hyper-Threading Limit Cpuid Max. toOn-Chip Primary PCI IDE Sata RAID / Ahci ModeOn-Chip Sata Mode Integrated PeripheralsUSB Controller Pata IDE Set toSata Port 0/2 Set to Sata Port 1/3 Set toUR2 Duplex Mode Onboard LAN1 Boot ROM LAN1 portOnboard LAN2 Boot ROM LAN2 port Uart Mode SelectECP Mode Use DMA Parallel Port ModeIf RTC Alarm Lead To Power On is Enabled Resume by AlarmPower On By Mouse Disabled Disable this function. Default value EnabledAC Back Function Power On By KeyboardKB Power on Password Before AC-power offCPU/POWER/SYSTEM FAN Fail Warning Current CPU TemperatureCurrent CPU/POWER/SYSTEM FAN Speed RPM CPU Warning TemperatureOperate at full speed CPU Smart FAN ModeFAN control mode for it. Default value CPU Smart FAN ControlCPU Host Clock Control CPU Clock RatioRobust Graphics Booster A.2Memory Frequency Mhz CPU Host FrequencyMhzPCI Express FrequencyMhz Memory Frequency ForSelect Language Load Fail-Safe DefaultsSet Supervisor/User Password Load Optimized DefaultsExit Without Saving Save & Exit SetupBios Setup English Install Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsPlease see the last page for details Hardware InformationContact Us This page lists all device you have for this motherboardEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionXpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery F9 For Xpress Recovery Exit and restart your computer Restores backup image to original stateRemove the backup image Exit and RestartDual Bios / Q-Flash Programming Utility Flash Bios Method IntroductionWhat is Dual Bios Technology? How to use Dual Bios and Q-Flash Utility?Halt On Error DisableDefault, Enable Wide Range Protection DisableDefault, EnableBoot From Main BIOSDefault, Backup Bios Auto Recovery EnableDefault, DisableBefore You Begin Method 1 Q-FlashTMUtilityTask menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two Press Y on your keyboard to load defaultsFlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility @BIOS utilityMethods and steps English RAID Levels Serial ATA Bios Setting Utility IntroductionDISK/VOLUME Information Configuring the Intel RAID BiosPress Enter under Create RAID Volume to set up RAID Create RAID Volume128KB Press Enter under the Create Volume item Delete RAID Volume Installing the RAID drivers Introduction of audio connectors Stereo Speakers Connection and Settings5 2- / 4- / 6- / 8- ChannelAudio Function Introduction Front Speaker Out Rear Speaker Out Channel Audio SetupEnglish Step Jack-Sensing Introduction AMI Bios Beep Codes TroubleshootingEnglish English English Taiwan Headquarters Contact UsChina Shanghai