Cisco Systems OL-3560-02 manual Synchronous Serial Specifications, LEDs, Distances

Page 3

Chapter 1 Overview

Synchronous Serial Specifications

Synchronous Serial Specifications

The PA-4T provides up to four synchronous serial interfaces. Each interface allows a maximum bandwidth of 2.048 Mbps; the speed depends on the type of electrical interface used. Use EIA/TIA-232 for speeds of 64 kilobits per second (kbps) and below, and use X.21, EIA/TIA-449, V.35, or EIA-530 for higher speeds.

Serial signals can travel a limited distance at any given bit rate; generally, the slower the baud rate, the greater the distance. All serial signals are subject to distance limits beyond which a signal degrades significantly or is completely lost.

Table 1-1lists the recommended (standard) maximum speeds and distances for each PA-4T serial interface type. The recommended maximum rate for V.35 is 2,048 Mbps.

Table 1-1 Standards for Transmission Speed Versus Distance

 

EIA/TIA-232

 

EIA/TIA-449, X.21, V.35, EIA-530

 

Distances

 

 

Distances

 

 

 

 

 

 

 

Rate (bps)

Feet

Meters

 

Feet

Meters

 

 

 

 

 

 

2400

200

60

 

4,100

1,250

 

 

 

 

 

 

4800

100

30

 

2,050

625

 

 

 

 

 

 

9600

50

15

 

1,025

312

 

 

 

 

 

 

19200

25

7.6

 

513

156

 

 

 

 

 

 

38400

12

3.7

 

256

78

 

 

 

 

 

 

56000

8.6

2.6

 

102

31

 

 

 

 

 

 

1544000 (T1)

 

50

15

 

 

 

 

 

 

Balanced drivers allow EIA/TIA-449 signals to travel greater distances than EIA/TIA-232. The recommended distance limits for EIA/TIA-449 shown in Table 1-1are also valid for V.35, X.21, and EIA-530. EIA/TIA-449 and EIA-530 support 2.048-Mbps rates, and V.35 supports 2.048-Mbps rates without any problems; we do not recommend exceeding published specifications for transmission speed versus distance. Do so at your own risk.

LEDs

The PA-4T contains the enabled LED, standard on all port adapters, and a one status LED for each port. After system initialization, the enabled LED goes on to indicate that the PA-4T has been enabled for operation. The LEDs are shown in Figure 1-2.

Figure 1-2 LEDs on the PA-4T—Horizontal Orientation Shown

EN

 

RD

RC

 

CD

TD

TC

LB

H4491

 

 

PA-4T Synchronous Serial Port Adapter Installation and Configuration

 

 

 

 

 

 

OL-3560-02

 

 

1-3

 

 

 

 

 

Image 3
Contents Port Adapter Overview OverviewSynchronous Serial Overview Distances Synchronous Serial SpecificationsLEDs EIA/TIA-232 EIA/TIA-449, X.21, V.35, EIA-530Cables, Connectors, and Pinouts PA-4T Port Adapter Receptacles and CablesLED Label Function Color and Function Overview Cables, Connectors, and Pinouts EIA/TIA-232 Connections EIA/TIA-449 Connections EIA-530 Connections 4T Port Adapter Cable PinoutsTxC/NIL TxCE/TxC RxC/TxCE NIL/RxC TxCE/TxC RxC/TxCE Mode Ground Shorting group ModeDCEShield ground TxD/RxD RxD/TxD Circuit groundTxCE/TxC+ Shield ground TxD/RxD+RxD/TxD+ TxD/RxD RxD/TxD TxC/RxC+TxCE/TxC+ TxCE+ Mode1 Ground Shorting group Mode2 ModeDCE VIP End, HD Network End Position Plug DB-25 PlugShield ground TxD/RxD+ TxD+ RxD/TxD+ RxC TxC/RxC+ TxC+ RxC/TxCE+RxD/TxD TxD/RxD TxCE/TxC+ Mode Shorting group Ground ModeDCE TxC/NIL RxC/TxCE RxC/TxDShield ground Frame ground Circuit ground TxD/RxD RxD/TxD RxD/TxD+Cisco 7200 Series Router Slot Numbering Port Adapter Slot Locations on the Supported PlatformsInterface processor slots are numbered as shown in Figure VIP Slot NumberingPlatform Interface Address Format Numbers Syntax Identifying Interface AddressesVIP Interface Addresses Cisco 7200 Series Routers Interface Addresses