Tripp Lite 3-Phase 30kVA Operation Normal Conditions, Initial Battery Charging, Wiring Connection

Page 7

Installation (continued)

WIRING CONNECTION

Connect your wiring to the input and output terminal blocks located on the rear panel of your UPS (see figure below).

CAUTION!

Qualified personnel should follow all procedures prescribed by N.E.C. and other local codes for hardwiring devices to a utility source.

Ensure that cables are fitted with cable sleeves and are secured by connector clamps. Tighten connections with a torque of not less than 35 inch-pounds. Observe the appropriate cable connection regulations [e.g. National Electrical Code (NEC) in the U.S.] at all times. Using cables of improper size may damage your equipment and cause fire hazards.

G N1 R1 S1 T1

N2 T2 S2 R2 G

NOTE: when shipped from the factory, bypass input and main input wires are connected.

For equipment requiring a neutral connection to an IT power distribution system, the disconnect device shall be a four-pole device and shall disconnect all line conductors and the neutral conductor. If a disconnect device interrupts the neutral conductor, it shall simultaneously interrupt all line conductors.

INITIAL BATTERY CHARGING

Although the internal batteries are charged prior to shipping, allow the internal batteries to charge uninterrupted for 24 hours after initial installation.

OUTPUT VOLTAGE SELECTION (VIA SOFTWARE)

The UPS's output voltage is factory set at 220/380V AC. If you require output voltage of 230/400V AC or 240/415V AC, you must change the UPS's output voltage via the included software interface.

The UPS must be in electronic bypass (press the “OFF” Button) prior to selecting the UPS's output voltage.

STEP 1) Load the included software CD on a computer which is connected to the UPS power module through the computer's COMM1 serial port. Note: the computer must have Windows® 98 or above installed in order to run the software.

STEP 2) In the Utility Directory, double-click on the “onlineconfig.exe” executable file.

STEP 3) Select output voltage, either 220/380, 230/400 or 240/415. (See screen image.)

Operation (Normal Conditions)

TURNING THE UPS ON

•Make sure the UPS is properly installed (see Installation section) and the Manual Bypass Switch is set to NORMAL.

•Turn the AC Main Input Switch and Bypass Input Switch Circuit Breakers ON.

•If your AC input is providing power normally within your selected range, your connected load will energize in Bypass. However, the UPS's inverter is not yet on. Press the front “ON” button to begin inverter operation.

•If your AC input is not providing power normally, you have the option of starting from battery. (Your battery must be at least partially charged for this operation to succeed.) Press and hold both the "Battery Start" switch and the “ON” button for three seconds to start your UPS in “ON BATTERY” mode. Note that some electronic equipment may draw more amps during startup; when starting from battery, consider reducing the initial load on the UPS.

•The UPS will perform a brief self-test and show the results on the LCD Display. (See Self-Testing section, for display sequence.) After a successful self-test, the UPS will provide AC power from the inverter to your load.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Español Français UPS Location Warnings Important Safety WarningsControl Panel Front PanelBattery Access Panel cover removed Rear Panel Rear PanelUPS Location InstallationMounting Bracket Installation UPS Input and Output Hardwire ConnectionOutput Voltage Selection VIA Software Initial Battery ChargingWiring Connection Operation Normal ConditionsLCD Display Select Button SELF-TESTINGSelf Testing Battery OK DC to DC OK Inverter Test Turning the UPS OFFOperation Under Shutdown Operation Special ConditionsOperation on BYPASS-VOLTAGE OUT of Range Inverter on WarningsCommunications Open Remote Emergency Power OFF EPODRY Contact Interface DRY Contact Interface TableAdding or Replacing Internal Batteries Do not Remove Battery SleeveBattery Packs are Heavy Check Battery Pack Voltage Before Completing InstallationInternal Battery Pack Wiring Diagram Adding or Replacing Internal Batteries Adding or Replacing Internal Batteries Adding or Replacing Internal Batteries Observe Proper Polarity ServiceWarranty Limited WarrantyModel SU20K3/3INT SpecificationsModel SU30K3/3INT Manual del Propietario Advertencias sobre la colocación y ubicación del UPS Advertencias de Seguridad ImportantesPanel DE Control Panel FrontalPanel DE Acceso a LA Bateria Tapa Removida Panel Frontal continuaciónPanel Trasero Panel TraseroConexion a Tierra InstalaciónUbicación DEL UPS Instalacion DE LOS Soportes DE MontajeEncendiendo EL UPS Operación Condiciones NormalesCarga Inicial DE LA Bateria Seleccion DEL Voltaje DE Salida VIA SoftwareBoton Select Seleccionar DE LA Pantalla LCD Operación Condiciones Normales continuaciónApagando EL UPS AUTO-PRUEBAOperacion Bajo CIERRE/PARADA Operación Condiciones EspecialesOperacion EN DERIVACION-VOLTAJE Fuera DE Rango Advertencias DEL Inversor EncendidoComunicaciones Operación Condiciones Especiales continuaciónTabla DE LA Interfaz DE Contacto Seco Comunicaciones continuaciónInterfaz DEL Contacto Seco Apagado DE Emergencia Remoto EPO¡NO Remueva LA Cubierta Protectora DE LA Bateria Añadiendo o Remplazando las Baterías Internas¡LOS Modulos DE Bateria SON Pesados Añadiendo o Remplazando las Baterías Internas continuación Diagrama DEL Cableado DEL Modulo DE Baterias InternasAñadiendo o Remplazando las Baterías Internas continuación Terminales ¡PELIGRO ¡OBSERVE LA Polaridad Correcta ServicioGarantía Garantia LimitadaModelo SU20K3/3INT EspecificacionesModelo SU30K3/3INT Especificaciones continuaciónManuel du propriétaire Mises en garde relatives à la localisation de londuleur Importantes consignes de sécuritéPanneau avant Panneau DE CommandePanneau Daccès AUX Batteries carter enlevé Panneau avant suitePanneau Arrière Panneau arrièreSélection DU Câblage IL Faut Installer Londuleur À Laide DE Brides DE FixationMises EN Garde Relatives À LA Localisation DE Londuleur Connexion DE Mise À LA TerreSélection DE LA Tension DE Sortie À Laide DUN Logiciel Installation suiteFonctionnement Conditions normales Première Charge DE LA BatterieBouton DE Sélection DE Lécran ACL Fonctionnement Conditions normales suiteArrêter Londuleur Éxécution DUN AUTO-TESTFonctionnement Pendant UN Arrêt Fonctionnement Conditions spécialesFonctionnement EN DÉRIVATION-TENSION Hors Plag Mises EN Garde Inverseur EN MarcheInterface RS-232 Commuter Londuleur EN Mode NormalFonctionnement Conditions spéciales suite Fonctionnement DU Commutateur DE Dérivation ManuelleInterface Contact SEC Ajout et remplacement des batteries internesArrêt Durgence Emergency Power OFF EPO À Distance Communications suiteSchéma DU Câblage Interne DUN Bloc DE Batterie Ajout et remplacement des batteries internes suiteAjout et remplacement des batteries internes suite Bornes Ajout et remplacement des batteries internes suite Garantie Limitée À VIE GarantieObserver LA Bonne Polarité Modèle SU20K3/3INT SpécificationsModèle SU30K3/3INT Spécifications suite

3-Phase 30kVA specifications

The Tripp Lite 3-Phase 30kVA is a robust power protection solution designed for demanding environments, such as data centers, industrial facilities, and large commercial spaces. This uninterruptible power supply (UPS) is engineered to deliver reliable and consistent power while safeguarding sensitive equipment from power fluctuations and outages, making it an ideal choice for businesses that require uninterrupted operations.

One of the main features of the Tripp Lite 3-Phase 30kVA UPS is its ability to provide a high power output of 30,000 VA, which translates to significant flexibility in powering multiple devices and systems simultaneously. This capacity is critical for operations that rely on extensive and mission-critical equipment, ensuring that everything continues to run smoothly even in the event of utility power failure.

The UPS is equipped with advanced technologies designed to enhance its performance. The double-conversion online design ensures that your connected equipment receives clean, stable, and filtered power. This technology isolates sensitive electronics from typical power issues such as surges, sags, and electrical noise, minimizing the risk of damage. Furthermore, the unit features a high-efficiency mode that reduces energy consumption, resulting in lower operating costs and environmental impact.

The Tripp Lite 3-Phase 30kVA UPS also comes with comprehensive monitoring and management capabilities. Its intelligent LCD interface provides real-time information on input/output voltage, battery status, and system configuration, allowing administrators to monitor the UPS easily and make informed decisions regarding power management. Additionally, it supports SNMP compatibility for remote management via a network, enabling IT teams to efficiently oversee power and UPS status from a distance.

Another notable characteristic is the UPS's scalable design, which allows for multiple units to be combined to create a highly efficient power system tailored to the specific needs of the facility. This scalability ensures that the power infrastructure can evolve with growing demands without requiring a complete overhaul.

Overall, the Tripp Lite 3-Phase 30kVA UPS stands out as a reliable, efficient, and user-friendly solution for organizations seeking to enhance their power protection strategy. With its high capacity, advanced technologies, and comprehensive management features, it is well-equipped to support critical operations and ensure business continuity in a world where power integrity is paramount.
Top Page Image Contents