Tripp Lite 93-2007 (200106010) owner manual Battery Selection, Selecting Battery Type

Page 8

Battery Selection

Selecting Battery Type

Select a battery or system of batteries that will provide your APS with proper DC voltage and an adequate amp hour capacity.* Select ‘Deep-Cycle’ batteries to enjoy optimum performance from your APS. Batteries of either Wet-Cell (vented) or Gel-Cell/Absorbed Glass Mat (sealed) construction are ideal. 6 Volt “golf-cart”, Marine Deep-Cycle or 8D Deep-Cycle batteries are also acceptable.**

*Even though APS models are high-efficiency converters of electricity, their rated output capacities are limited by the amp-hour size of the external batteries. ** You must set Configuration DIP Switch #1, Group A (Battery Type) to match the type of batteries you connect or your batteries may be degraded or damaged over an extended period of time. See “APS Configuration,” page 5 for more information.)

Selecting Battery Amp Hour Capacity

1.Add the Wattage Ratings of your connected equipment to determine the Total Wattage Required.*

2.Divide the Total Wattage Required (from Step 1) by the battery voltage to determine the DC Amperes Required.

3.Multiply the DC Amperes Required (from Step 2) by the number of hours you estimate will pass without AC power before your battery can recharge to determine a Battery Amp-Hours Required Rough Estimate.**

4.Compensate for inefficiency by multiplying your Battery Amp-Hour Required Rough Estimate (from Step 3) by 1.2 to determine how many amp-hours of battery backup (from one or several batteries) you should connect to your APS. Note that the Amp-Hour ratings of batteries are usually given for a 20 hour discharge rate. Actual Amp-Hour capacities are less when batteries are discharged at faster rates: batteries discharged in 55 minutes provide only about 50% of their listed Amp-Hour ratings, while batteries discharged in 9 minutes provide as little as 30% of their Amp-Hour ratings.

*The wattage rating is usually stated in the equipment’s manuals or on their nameplates. If your equipment is rated in amperes, convert to watts by multiplying the ampere rating by your nominal AC line voltage (230). ** Your charging amps multiplied by the charging hours must exceed the discharge amp-hours taken from the batteries between charges or you will eventually run down your battery bank.

Mounting (Optional) (See Diagram 2, p. 36)

Horizontal mounting should be used for all vehicular applications. Due to their size and weight, all APS PowerVerter systems in vehicles should be mounted on a rigid horizontal (not vertical) surface, mounting plate or bracket before battery connection.User must supply all fasteners and brackets and verify their suitability for use with the intended mounting surface. Turn your APS PowerVerter and connected equipment OFF before mounting.

•Install two 8 mm (1/4 in.) fasteners (A) into a rigid horizontal surface using the measurements in the diagram. Leave the heads of fasteners raised slightly above the surface in order to engage the slots in the APS’s feet.

•Slide PowerVerter forward to fully engage the fasteners in the APS’s feet. Install two 8 mm (1/4 in.) fasteners (B) into the surface, through the slots in the APS’s two unsecured feet. Tighten the screws to secure the APS in position.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents APS PowerVerter Introduction Circuit Board Protection Stage Battery ChargerFrequency-Controlled Inverter Output Battery Connection Warnings APS Location WarningsEquipment Connection Warnings Operation WarningsConfiguration DIP Switch Group a All modelsSelect High AC Voltage Switch To Select Low AC Voltage Switch ToBattery Charger Limiting Points Load SHARING/EQUALIZE Battery ChargeEqualize Battery Charge DIP Switch #3, Group B Setting ProcedureSelecting Battery Amp Hour Capacity Battery SelectionSelecting Battery Type DC Vehicular Battery ConnectionStandard AC Input Electrical Connection All corded models AC ConnectionDC Ground Connection Switches, Indicator Lights & Other Features Set Operating Mode SwitchSwitches AC Output Electrical Connection All corded modelsIndicator Lights Other Features Service Maintenance & ServiceMaintenance Symptom Problems Corrections Specifications Corded Models InverterSpecifications Hardwired Models Diagrams/Esquemas See Hardwire Electrical Connections, pgVolts Basic 12VDC Vehicular Battery Connection. See Pg Corded Model Modelo con Cable Hardwired Model Modelo con Toma Directa al Circuito

93-2007 (200106010) specifications

Tripp Lite 93-2007 (200106010) is a high-quality audio-visual interface designed to facilitate seamless connection between various devices. This device is particularly popular in professional settings such as conference rooms, educational environments, and home theaters, where robust performance and unerring reliability are essential.

One of the primary features of the Tripp Lite 93-2007 is its extensive compatibility. The device supports a wide range of formats, making it suitable for use with multiple devices like projectors, televisions, and computer systems. Its ability to handle both analog and digital signals ensures users can enjoy exceptional audio and video quality without compromise.

Tripp Lite has engineered the 93-2007 with advanced technology that minimizes signal degradation. It employs high-quality shielding to protect against electromagnetic interference (EMI) and radio frequency interference (RFI). This shielding is vital for maintaining the integrity of signals over longer distances, making it suitable for setups in large venues where distance can impact performance.

The build quality of the Tripp Lite 93-2007 is noteworthy, with durable connectors that provide a secure fit and resist wear and tear over time. This longevity ensures that users will not have to frequently replace cables, creating a more efficient installation process. Moreover, the connectors are designed for easy plug-and-play functionality, allowing for quick setup and disconnection, ideal for fast-paced environments where time is critical.

Another key characteristic of the Tripp Lite 93-2007 is its ability to support high-definition resolutions. Whether you're working with 720p, 1080p, or even 4K content, this device guarantees sharp and clear imagery. As the demand for high-definition content continues to rise, having a reliable interface that can handle various resolutions is essential.

In addition to its performance, the Tripp Lite 93-2007 is engineered to be user-friendly. Its compact design allows for straightforward management of cables, reducing clutter. Moreover, it is compatible with various mounting systems, ensuring flexibility in installations.

The Tripp Lite 93-2007 (200106010) stands out as a versatile and reliable solution for audio-visual connectivity. Its comprehensive features, durable design, and high-quality performance make it an excellent choice for both professional and personal applications. Users can trust this device to deliver top-notch audio-visual experiences that meet the demands of modern technology.
Top Page Image Contents