Tripp Lite 93-2007 (200106010) owner manual Battery Connection, Standard, DC Vehicular

Page 9

Battery Connection

Standard

1.Connect your APS’s positive DC Terminal directly to a fuse.

Tripp Lite recommends that you install a recognized component fuse block and fuse within 18 inches of the battery. The fuse's rating must equal or exceed the Minimum DC Fuse Rating listed in your APS model’s specifications on pages 16 or 17.

2.Choose a battery configuration appropriate to your batteries.

•Single Battery Connection: Refer to Diagram 4, page 37. When using a single battery, its voltage must be equal to the voltage of your APS’s Inverter Nominal Input Voltage (see specs).

•Parallel Battery Connection: Refer to Diagram 5, page 37. When using multiple batteries in parallel, each battery's voltage must be equal to the voltage of your APS’s Inverter Nominal Input Voltage (see specs).

•Series Battery Connection: Refer to Diagram 6, page 37. When using multiple batteries in series, all batteries must be equal in voltage and amp hour capacity, and the sum of their voltages must be equal to the voltage of your APS's Inverter Nominal Input Voltage (see specs).

3.Use 2/0 gauge wire ONLY to make external battery connections. Tighten battery terminals to a torque of 4 N-m.

Battery connection cable lengths should be short as possible, and must not exceed the Maximum Cable Length listed under Specifications, page 16 or 17. Shorter and heavier gauge cabling limits DC voltage drop and allows for maximum transfer of current.* You must tighten your battery terminals to approximately 4 Newton-meters of torque to create an efficient connection and prevent excessive heating. Insufficiently tightening terminals could void your PowerVerter’s warranty.

*APS models are capable of delivering a much higher wattage output for brief periods of time. Wiring should be configured to handle this brief high-current draw. Though your APS is a high-efficiency converter of electricity, its rated output capacity is limited by the length and gauge of the wires running from the battery to the APS.

DC Vehicular

APS systems may be permanently mounted in a car, truck or boat and connected to draw power from the vehicle’s battery. Note: An APS can ONLY be connected to vehicle batteries with voltage that matches the APS’s Nominal DC Input—12V vehicle batteries to 12V Nominal DC Input APS systems, etc. (See Specifications). There are two main ways to make this sort of vehicular battery connection. Choose the Basic Connection if you are running light hand tools or other small appliances for a brief period of time (see Diagram 7, p. 38). Choose the Advanced Connection if you are using your APS to power heavy loads for extended periods of time (see Diagram 8, p. 38). The Advanced Connection incorporates a battery isolator and separate battery system to provide battery power to your APS while preventing it from draining your vehicle’s battery. Note: Depending on your application, you may require more than one Deep Cycle Battery.

Caution: Never operate your APS from an alternator without a battery connected as shown in Diagrams 7 or 8, p. 38.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents APS PowerVerter Introduction Stage Battery Charger Frequency-Controlled Inverter OutputCircuit Board Protection APS Location Warnings Battery Connection WarningsEquipment Connection Warnings Operation WarningsDIP Switch Group a All models ConfigurationSelect High AC Voltage Switch To Select Low AC Voltage Switch ToLoad SHARING/EQUALIZE Battery Charge Battery Charger Limiting PointsSetting Procedure Equalize Battery Charge DIP Switch #3, Group BBattery Selection Selecting Battery TypeSelecting Battery Amp Hour Capacity Battery Connection StandardDC Vehicular AC Connection DC Ground ConnectionAC Input Electrical Connection All corded models Set Operating Mode Switch Switches, Indicator Lights & Other FeaturesSwitches AC Output Electrical Connection All corded modelsIndicator Lights Other Features Maintenance & Service MaintenanceService Symptom Problems Corrections Inverter Specifications Corded ModelsSpecifications Hardwired Models See Hardwire Electrical Connections, pg Diagrams/EsquemasVolts Basic 12VDC Vehicular Battery Connection. See Pg Corded Model Modelo con Cable Hardwired Model Modelo con Toma Directa al Circuito

93-2007 (200106010) specifications

Tripp Lite 93-2007 (200106010) is a high-quality audio-visual interface designed to facilitate seamless connection between various devices. This device is particularly popular in professional settings such as conference rooms, educational environments, and home theaters, where robust performance and unerring reliability are essential.

One of the primary features of the Tripp Lite 93-2007 is its extensive compatibility. The device supports a wide range of formats, making it suitable for use with multiple devices like projectors, televisions, and computer systems. Its ability to handle both analog and digital signals ensures users can enjoy exceptional audio and video quality without compromise.

Tripp Lite has engineered the 93-2007 with advanced technology that minimizes signal degradation. It employs high-quality shielding to protect against electromagnetic interference (EMI) and radio frequency interference (RFI). This shielding is vital for maintaining the integrity of signals over longer distances, making it suitable for setups in large venues where distance can impact performance.

The build quality of the Tripp Lite 93-2007 is noteworthy, with durable connectors that provide a secure fit and resist wear and tear over time. This longevity ensures that users will not have to frequently replace cables, creating a more efficient installation process. Moreover, the connectors are designed for easy plug-and-play functionality, allowing for quick setup and disconnection, ideal for fast-paced environments where time is critical.

Another key characteristic of the Tripp Lite 93-2007 is its ability to support high-definition resolutions. Whether you're working with 720p, 1080p, or even 4K content, this device guarantees sharp and clear imagery. As the demand for high-definition content continues to rise, having a reliable interface that can handle various resolutions is essential.

In addition to its performance, the Tripp Lite 93-2007 is engineered to be user-friendly. Its compact design allows for straightforward management of cables, reducing clutter. Moreover, it is compatible with various mounting systems, ensuring flexibility in installations.

The Tripp Lite 93-2007 (200106010) stands out as a versatile and reliable solution for audio-visual connectivity. Its comprehensive features, durable design, and high-quality performance make it an excellent choice for both professional and personal applications. Users can trust this device to deliver top-notch audio-visual experiences that meet the demands of modern technology.
Top Page Image Contents