Tripp Lite RELAYIOCARD owner manual Configuration, 3OHDVHQWHURXU&KRLFH

Page 3

2.Installation and Setup (continued)

2.3Configuration

1.Press Enter to open the main menu of the RELAYIOCARD. Press 1 to configure the alarm event for R1~R6.

 _8365HOD\&DUG_  )LUPZDUH9HUVLRQ5HOD\&DUG9 >@&XVWRPL]H2XWSXW5HOD\ >@&RQILJXUH,QSXW6LJQDO >@&XVWRPL]H1RUPDO2SHQRU1RUPDO&ORVH >@4XLW

3OHDVH(QWHU<RXU&KRLFH !

2.Note: Contacts R1~R6 can be configured for different power events.

 _&XVWRPL]H2XWSXW5HOD\_ 

5HOD\6HOHFWHG(YHQW

>@5HOD\6XPPDU\$ODUP >@5HOD\3RZHU)DLO >@5HOD\%DWWHU\/RZ >@5HOD\2Q%\SDVV >@5HOD\2YHUORDG >@5HOD\2YHU7HPSHUDWXUH >@%DFN7R3UHYLRXV0HQX

3OHDVH(QWHU<RXU&KRLFH !

4.Press 3 to configure the normal open or normal close for each relay.

 _&XVWRPL]H2XWSXW5HOD\_ 

5HOD\6HOHFWHG(YHQW

>@5HOD\1RUPDO&ORVH >@5HOD\ 1RUPDO2SHQ >@5HOD\ 1RUPDO&ORVH >@5HOD\1RUPDO2SHQ >@5HOD\1RUPDO&ORVH >@5HOD\1RUPDO2SHQ >@%DFN7R3UHYLRXV0HQX

3OHDVH(QWHU<RXU&KRLFH !

Once the configuration is complete, SW2 must be switched ON to apply the new settings. To automatically reset to default settings, switch SW2 to the OFF position.

5.Press 0 to quit the configuration session. When the system prompts you to save your settings, press Y to save or N to ignore.

Application Example

Using the default settings, set SW1 and SW2 to OFF. Apply 12V DC to Common contact and connect the lamps to R1~R6 terminals. Install a push button from the Common contact to the input terminal. Press the button for at least 3 seconds to shut down the UPS remotely.

3.Press 2 to configure the input signal.

 _&RQILJXUH,QSXW6LJQDO_  >@$FWDV6KXWGRZQRU7HVW6KXWGRZQ >@,QSXW6LJQDO&RQILUP6HFRQGV >@'HOD\%HIRUH6KXWGRZQ6HFRQGV >@%DFN7R3UHYLRXV0HQX

3OHDVH(QWHU<RXU&KRLFH !

Common +12V

GND-R

R1

R2

R3

R4

R5

R6

Input

Summary Alarm

Power Fail

Battery Low

On Bypass

Overload

Over Temperature

Shutdown UPS

In this menu, the input signal can be redefined as a shutdown UPS signal or battery test signal. The UPS shutdown delay time can be adjusted to a maximum of 9999 seconds.

3

200805102 93-2815.indd 3

7/15/2008 9:19:00 AM

Image 3
Contents Introduction Installation and SetupSpecifications Warranty & Warranty Registration Programmable Relay I/O CardIntroduction Installation and Setup3OHDVHQWHURXU&KRLFH ConfigurationWarranty & Warranty Registration SpecificationsEspecificaciones Instalación y ConfiguraciónTarjeta de E/S de Relé Programable IntroducciónIntroducción Instalación y ConfiguraciónInstalación y Configuración continuación ConfiguraciónPresione 2 para configurar la señal de entrada Especificaciones English Español Installation et configurationCarte de relais I/O programmable SpécificationsDéfinition produit Installation et configurationConfiguration requise Configuration des communicationsAppuyez sur 2 pour configurer le signal d’entrée Spécifications