Moxa Technologies CP-132U Series user manual Windows Click Other Locations

Page 41

Software Installation

If one MOXA CP-168U board was previously installed and another MOXA CP-168U board is plugged in, the system will prompt you to skip this stage, and take care of Port Configuration, which is discussed in the next section.

1.Upon detecting the first new Smartio CP-168U Series board, Windows 95/98 will automatically display a New hardware found message box, and then display the following dialog boxes. Click the Next button to proceed.

Windows 95

Windows 98

2. Click [Other Locations].

2. Select [Display a list...] and then click [Next].

CP-132U Series User’s Manual 3-27

Image 41

Contents CP-132U Series User’s Manual Disclaimer Copyright NoticeTrademarks Moxa Internet Services Table of Contents Introduction Overview Industio-The Industrial Multiport Async SolutionAddc Automatic Data Direction Control for RS-485 Termination Resistors Ready for RS-422/485Universal PCI Introduction PCI SolutionOperating System Support Moxa Serial Comm ToolsPackage Checklist FeaturesHardware Installation CP-132UL Series Block Diagram CP-132UL-I V2 120 x 64.5 mm CP-132U-I V1 120 x 100 mm CP-132UL V2 120 x 64.5 mm CP-132UL V1 120 x 64.5 mm DIP Switch Port Settings Installing the CP-132UL Series Board CPCI Boards CT-114I Software InstallationWindows Installing the Driver Software Installation CP-132U Series User’s Manual Software Installation Using Device Manager How to Check the InstallationPort Configuration CP-132U Series User’s Manual Using PComm Windows 2000/XP Using Event LogWindows Windows XP Select Install from a list or specificSoftware\Win2K-XP-2003 folder on Software Installation Software from a specific location Next Welcome to the Found NewSelect Specify a location and then click Next to continue 16 CP-132U Series User’s Manual Software Installation Device Manager Port Configuration 20 CP-132U Series User’s Manual Event Log Moxa PComm UtilityRemoving the Driver Click OK to proceed with the un-installation of the board Windows 95/98 Installing the Driver See the section, Board and Ports Ready First Time Driver InstallationInstallation Windows Click Other Locations Type \Software\Win9x\Windows Windows Software Installation Board and Port ReadyConfiguring the Board and Ports Software Installation Updating the Driver Software Installation Removing the Driver Windows NT 36 CP-132U Series User’s Manual Software Installation 38 CP-132U Series User’s Manual Software Installation Re-Configuring Port Settings Configuring the Board and PortsSoftware Installation Configuring Another CP-168U Board Removing an Existing CP-168U Board Configuration 44 CP-132U Series User’s Manual DOS 46 CP-132U Series User’s Manual Run the BIN\SETUP.EXE file Setting up the DriverPort number TxD buffer size Loading the DriverRxD buffer size F5 Group EditUnloading the Driver LinuxSoftware Installation Page Serial Programming Tools PComm InstallationUtilities Diagnostic for Moxa boards onlyPComm Programming Library CP-132U Series User’s Manual Start#Program#Pcomm Lite#Terminal Emulator Terminal EmulatorAddc Automatic Data Direction Control RS-485 ProgrammingSolution Connection Cables Cable Wiring RS-485 Interface RS-422/485 Pinouts and Cable WiringRS-422 Interface Pinouts Connection Cables and Cables WiringRS-422/485 pinouts for CP-132UL Series CBL-M25M9x2RS-422 pinouts for CP-132UL Series Wire RS-485 pinouts for CP-132ULWire RS-485 pinouts for CP-132UL Series RS-422 Point-to-point RS-422 Broadcasting Cable WiringMultidrop 4-wire RS-485 full-duplex Impedance Matching and Termination Resistors Page General Troubleshooting TroubleshootingSoftware Causes and Solutions Windows NT system panic blue screen Technical ReferenceCOM number of the CP-132U Series conflicts with others System fails to find the CP-132U Series board Technical Reference SpecificationsPCI Return Procedure Revision History