Moxa Technologies UC-7420/7410 user manual Hardware Connection Description, DIN-Rail Mounting

Page 14

UC-7420/7410 User’s Manual

Introduction

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate is included in the package. If you need to reattach the DIN-Rail attachment plate to UC-7420/7410, make sure the stiff metal spring is situated towards the top, as shown in the figures below.

1.Insert the top of the DIN-Rail into the slot just below the stiff metal spring.

2.The DIN-Rail attachment unit will snap into place as shown below.

metal spring

metal spring

DIN-Rail

DIN-Rail

To remove UC-7420/7410 from the DIN-Rail, simply reverse Steps 1 and 2 above.

Hardware Connection Description

This section describes how to connect UC-7420/7410 to serial devices for first time testing purposes. We cover Wiring Requirements, Connecting the Power, Grounding UC-7420/7410, Connecting to the Network, Connecting to a Serial Device, Connecting to the Console Port, PCMCIA, and CompactFlash.

Wiring Requirements

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or wiring your UC-7420/7410.

Wiring Caution!

Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes dictating the maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could overheat, causing serious damage to your equipment.

Temperature Caution!

Be careful when handling UC-7420/7410. When plugged in, UC-7420/7410’s internal components generate heat, and consequently the outer casing may feel hot to the touch.

You should also observe the following common wiring rules:

yUse separate paths to route wiring for power and devices. If power wiring and device wiring paths must cross, make sure the wires are perpendicular at the intersection point.

NOTE: Do not run signal or communication wiring and power wiring in the same wire conduit. To avoid interference, wires with different signal characteristics should be routed separately.

1-9

Image 14

Contents UC-7420/7410 User’s Manual Third Edition, JuneDisclaimer Copyright NoticeTrademarks Table of Contents Chapter UC Finder Appendix B Windows Tool Chain Introduction Introduction ‰ Hardware IntroductionOverview Package ChecklistProduct Features UC-7410-LXProduct Hardware Specifications Appearance Appearance and DimensionsHardware Introduction Dimensions LED Name Color Meaning Hardware Block DiagramLED Indicators Reset to default Button Reset-type ButtonsReset Button Real Time ClockPlacement Options Wall or CabinetDIN-Rail Mounting Wiring RequirementsHardware Connection Description Pin Signal Connecting the PowerConnecting to the Network Grounding UC-7420/7410CompactFlash Connecting to a Serial DeviceConnecting to the Console Port Pin RS-232 RS-422 RS-485Software Introduction Software ArchitectureJournaling Flash File System JFFS2 Software PackageSoftware Version Comparison Table Protocol stacks and utilities Directory Change‰ Configuring the Ethernet Interface Getting StartedSerial Console Powering on UC-7420/7410Connecting UC-7420/7410 to a PC 192.168.3.127 255.255.255.0 Default IP Address NetmaskTelnet Console 192.168.4.127 255.255.255.0SSH Console Windows UsersLinux Users Configuring the Ethernet InterfaceModifying Network Settings with the Serial Console Static IP addressesDynamic IP addresses Default IP address is 192.168.5.127, netmask Configuring the Wlan via the Pcmcia InterfaceModifying Network Settings over the Network IEEE802.11b#vi /etc/wlan/wlancfg-any IEEE802.11g Setting Explanation SettingKey1Str, Key2Str, Key3Str, Key4Str-Sets strings Key1 to Key4 TurboRate-Enables or disables TurboRate Checking the Flash Memory Space Installing the Tool Chain LinuxTest Program-Developing Hello.c StepCompiling Hello.c You should receive the following responseUploading Hello to UC-7420/7410 and Running the Program Testing EnvironmentDeveloping Your First Application Compiling tcps2.c #mount -t iso9660 /dev/cdrom /mnt/cdromUploading tcps2-release and Running the Program PuTTY#jobs // use this command to check if the program is running Testing Procedure Summary UC-7420/7410 User’s ManualUC-7420/7410 User’s Manual ‰ System Version Information ‰ System Image Backup Managing Embedded LinuxUpgrading the Firmware System Image BackupSystem Version Information Upgrading the firmware will erase all data on the Flash ROM#upramdisk #cd /mnt/ramdisk Loading Factory Defaults Firmware version V1.5 and later versions Backing Up the User File SystemFirmware versions earlier than V1.5 not including Enabling and Disabling Daemons UC-7420/7410 User’s Manual Managing Embedded Linux Setting the Run-Level Adjusting the System Time Setting the Time ManuallyUpdating the Time Automatically Example shell script to update the system time periodicallyNTP Client Enable the cron daemon manually Cron-daemon to Execute Scheduled CommandsChange mode of fixtime.sh Enable cron when the system boots upCF Mass Storage Connecting PeripheralsUSB Mass Storage Managing Communications ‰ Iptables ‰ NATEnabling the Telnet/ftp server Web Service-ApacheTelnet / FTP Disabling the Telnet/ftp serverUsr/www/cgi-bin Saving a Web Page to the CF Card Use the following commands to restart the Apache web server Iptables Local Host Packets Usage Observe and erase chain rulesDefine policy for chain rules ExamplesAppend or delete rules IptmacEnabling NAT at Bootup NAT ExampleDial-up Service-PPP Example 2 Connecting to a PPP server over a hard-wired link How to check the connection UP Loopback RunningNFS Network File System Setting up UC-7420/7410 as an NFS ServerSetting up a Machine for Incoming PPP Connections #vi /etc/exportsSetting up UC-7420/7410 as an NFS Client Mail Steps 2Open VPN Internet IFS=‘ Create link symbols to enable this script at boot time Destination Gateway Genmsk Flags Metric Use Iface Now ping Host B from Host a by typing Setup 3 Routed IP Destination Gateway Genmsk Flags Metric Use Iface Programmer’s Guide Linux Tool Chain Introduction Address Size ContentsFlash Memory Map Cross Compiling Applications and Libraries Debugging with GDBObtaining help Tools Available in the Host EnvironmentBuzzer Device APIRTC Real Time Clock WDT Watch Dog Timer Input Int fd File handle from swtdopen return value Output Special Note User application example ExampleSwtddisableswtdfd Int mainint argc, char *argv Pidt sonpid Example to set the baud rate Example to get the baud rateSpecial Note KeyPadBaud rate inaccuracy ExamplesMake File Example UC Finder Installing the Software Windows UC FinderUC-7420/7410 User’s Manual UC Finder Broadcast Search Linux ucfinder File manager System CommandsBusybox V0.60.4 Linux normal command utility collection EditorMoxa special utilities ProcessOther Windows Tool Chain Introduction Introduction Installation Procedure Select the Root DirectoryUC-7420/7410 User’s Manual Windows Tool Chain Introduction UC-7420/7410 User’s Manual Windows Tool Chain Introduction Using the Bash Shell GDB debug tool-Insight UC-7420/7410 User’s Manual Windows Tool Chain IntroductionUC-7420/7410 User’s Manual Windows Tool Chain Introduction Service Information Moxa Internet Services Following services are providedProblem Report Form Moxa Product † UC-7410-LX † UC-7420-LX Serial NumberProduct Return Procedure