Moxa Technologies NPort 5600 user manual Serial Parameters

Page 40

NPort 5600 Series User’s Manual

Configuring NPort Administrator

Serial Parameters

ATTENTION

Check the serial communication parameters in your Serial Device’s user’s manual. You should set up NPort’s serial parameters with the same communication parameters used by your serial devices.

Baudrate

Setting	Factory Default	Necessity
50 bps to921.6 Kbps	115.2 Kbps	Required
Data bits
Setting	Factory Default	Necessity
5, 6, 7, 8	8	Required

When the user sets Data bits to 5 bits, the stop bits setting will automatically change to 1.5 bits.

Stop bits

Setting	Factory Default	Necessity
1, 1.5, 2	1	Required

Stop bits will be set to 1.5 when Data bits is	set to 5 bits.
Parity
Setting	Factory Default	Necessity
None, Even, Odd, Space, Mark	None	Required

Flow control
Setting	Factory Default	Necessity
None, RTS/CTS, DTR/DSR, Xon/Xoff	RTS/CTS	Required

FIFO
Setting	Factory Default	Necessity
Enable, Disable	Enable	Required

NPort’s serial ports provide a 16-byte FIFO both in the Tx and Rx directions. Disable the FIFO setting when your serial device does not have a FIFO to prevent data loss during communication.

Interface

Setting	Factory Default	Necessity
NPort 5610-16/8: RS-232 only	RS-232 only	Required
NPort 5630-16/8: RS-422/485 only	4-wire RS-485	Required

NPort 5650-16/8	RS-232	Required

5-10

Image 40

Contents NPort 5600 Series User’s Manual Seventh Edition, JulyTrademarks Copyright NoticeDisclaimer Table of Contents Chapter IP Serial LIB Page Introduction Product Features Package ChecklistOverview Product Specifications Advanced Built-in Features Software FeaturesPower Requirements Serial Communication Parameters‰ Panel Layout ‰ Connecting the Hardware Getting StartedRear panel of NPort 5600 series AC Power Rear panel of NPort 5600 series DC PowerPanel Layout Front panel of NPort 5600 seriesConnecting the Hardware Wiring RequirementsConnecting NPort 5610/30/50-16/8’s Power Connecting NPort 5610-16/8-48V’s PowerConnecting to the Network Grounding NPort 5610-16/8-48VConnecting to a Serial Device LED IndicatorsLink Indicator on the Rear Panel of NPort 5650 Fiber Model Adjustable Termination Resistor for the RS-485 PortNPort 5650 DIP Switches Initial IP Address Configuration Factory Default IP Address Default IP addressInitializing NPort’s IP Address LCM DisplayButton Name Action Detailed Menu OptionsLevel NPort Administration Suite ARPTelnet Console NPort 5600 Series User’s Manual NPort 5600 Series User’s Manual NPort 5600 Series User’s Manual Choosing the Proper Operation Mode Real COM Mode Real COM ModeTCP Server Mode TCP Server ModeUDP Mode TCP Client ModePair Connection Mode Disabled Mode Reverse Telnet ModeRFC2217 Mode PPP Mode Web Console Configuration Opening Your Browser Basic Settings Time Server nameTime zone Local timeNetwork Settings ConsoleIP Configuration IP AddressNetmask GatewaySnmp Settings DNS server 1 / DNS serverCommunity name ContactIP Address Report Auto report to IPAuto report to TCP port Auto report periodSerial Settings Port aliasSerial Parameters Operating Settings Real COM ModeSetting Factory Default Necessity To 99 min Min Optional TCP alive check timeMax connection Setting Factory Default Necessity Required Max. connectionMax connection 2 to Ignore jammed IPPacking length Setting Factory Default Necessity Required DelimiterDelimiter process Force transmitTCP Server Mode Max connection Packing length Setting Factory Default Necessity 4001 Required Command portSetting Factory Default Necessity 966 Optional Local TCP portTCP Client Mode Inactivity timeIgnore jammed IP Delimiter process Destination IP address Destination IP address 2/3/4Designated Local Port 1/2/3/4 Connection controlConnect/Disconnect Description UDP Mode Force transmit Pair Connection Master Mode Pair Connection ModeSetting Factory Default Necessity To 99 min Min Required Pair Connection Slave Mode BlankSetting Factory Default Necessity To 99 min Optional Reverse Telnet ModeMap CR-LF Disabled Mode RFC2217 ModePacking length Setting Factory Default Necessity Optional Setting Factory Default Necessity To FF hex None OptionalSetting Factory Default Necessity Yes or No Optional PPP ModeTCP/IP compression Accessible IP Settings Source IP addressIP netmask Modem Initial streamHosts on a specific subnet can access the NPort Any host can access the NPortPPP User Table Allowable Hosts Input formatAuto warning E-mail and Snmp Trap Auto Warning SettingsMail Server Event Type Snmp Trap ServerSetting Factory Default Necessity Enable, Disable Optional DCD changedDSR changed MailMonitor Line MonitorMonitor Async Change Password Monitor Async-SettingsLoad Factory Defaults Configuring NPort Administrator ‰ Overview ‰ Installing NPort Administrator ‰ ConfigurationInstalling NPort Administrator NPort 5600 Series User’s Manual IP Serial LIB NPort 5600 Series User’s Manual IP Serial LIB Configuration Broadcast Search Unlock Password Protection NPort 5600 Series User’s Manual IP Serial LIB Lock UnlockBlank FixedConfiguring NPort NPort 5600 Series User’s Manual IP Serial LIB Upgrading Firmware Export/Import Add Target Æ Select target from the list Select Add Target NPort 5600 Series User’s Manual IP Serial LIB NPort 5600 Series User’s Manual IP Serial LIB NPort 5600 Series User’s Manual IP Serial LIB NPort 5600 Series User’s Manual IP Serial LIB Port Monitor COM MappingOn-line COM Mapping NPort 5600 Series User’s Manual IP Serial LIB Fast Flush only flush local buffer NPort 5600 Series User’s Manual IP Serial LIB Off-line COM Mapping IP Location NPort 5600 Series User’s Manual IP Serial LIB IP Serial LIB Why Use IP Serial Library? What is IP Serial Library?How to install IP Serial Library? IP Serial LIB Function Groups Example ProgramServer Control Port Control Input/Output Data Port Status MiscellaneousPinouts and Cable Wiring ‰ Cable Wiring DiagramsEthernet Port Pinouts Port Pinout DiagramsSerial Port Pinouts Cable Wiring Diagrams RJ45 8-pins to Female DB9Ethernet Cables Serial Cables for NPort 5610/5650 RS-232RJ45 8-pins to Male DB9 RJ45 8-pins to Female DB25Serial Cables for NPort 5630 RS-422/4-wire RS-485 RJ45 8-pins to Female DB25Serial Cables for NPort 5630 2-wire RS-485 NPort 5600 Series User’s Manual Well Known Port NumbersSerial Cables for NPort 5650 RS-422/4-wire RS-485 Serial Cables for NPort 5650 2-wire RS-485 RJ45 8-pins to Male DB25Pin Assignments for DB9 and DB25 Connectors Pin Assignments for DB9 Male and Female ConnectorsPin Assignments for DB25 Male and Female Connectors TCP Socket Application Service Well Known Port NumbersUDP Socket Application Service Snmp Agent with MIB II & RS-232 Like GroupSnmp Agent with MIB II & RS-232 Like Group System MIB Interfaces MIB Address Translation MIBInput Signal Table Output Signal Table Auto IP Report Protocol Auto IP Report Format Info nID List AP ID & Hardware ID Mapping TableService Information Moxa Internet Services Following services are providedMoxa Product Problem Report FormSerial Number Product Return Procedure