Moxa Technologies NPort 5600 user manual Packing length Setting Factory Default Necessity Optional

Page 59

NPort 5600 Series User’s Manual		Configuring NPort Administrator
	Packing length
	Setting	Factory Default	Necessity
	0 to 1024	0	Optional

Default = 0, The Delimiter Process will be followed, regardless of the length of the data packet. If the data length (in bytes) matches the configured value, the data will be forced out. The data length can be configured for 0 to 1024 bytes. Set to 0 if you do not need to limit the length.

Delimiter 1

Setting	Factory Default	Necessity
00 to FF (hex)	None	Optional
Delimiter 2
Setting	Factory Default	Necessity
00 to FF (hex)	None	Optional

Once the NPort 5600 receives both delimiters through its serial port, it immediately packs all data currently in its buffer and sends it to the NPort 5600’s Ethernet port.

ATTENTION

Delimiter 2 is optional. If left blank, then Delimiter 1 alone trips clearing of the buffer. If the size of the serial data received is greater than 1 KB, the NPort 5600 will automatically pack the data and send it to the Ethernet. However, to use the delimiter function, you must at least enable Delimiter 1. If Delimiter 1 is left blank and Delimiter 2 is enabled, the delimiter function will not work properly.

Delimiter process

	Setting	Factory Default	Necessity
	Do nothing
	Delimiter + 1	Do Nothing	Optional
	Delimiter + 2	Do Nothing	Optional
	Delimiter + 2
	Strip Delimiter

[Delimiter + 1] or [Delimiter + 2]: The data will be transmitted when an additional byte (for Delimiter +1), or an additional 2 bytes (for Delimiter +2) of data is received after receiving the Delimiter.

[Strip Delimiter]: When the Delimiter is received, the Delimiter is deleted (i.e., stripped), and the remaining data is transmitted.

[Do nothing]: The data will be transmitted when the Delimiter is received.

Force transmit

Setting	Factory Default	Necessity
0 to 65535 ms	0 ms	Optional

0: Disable the force transmit timeout.

1 to 65535: Forces the NPort 5600’s TCP/IP protocol software to try to pack serial data received during the specified time into the same data frame.

5-29

Image 59

Contents Seventh Edition, July NPort 5600 Series User’s ManualDisclaimer Copyright NoticeTrademarks Table of Contents Chapter IP Serial LIB Page Introduction Overview Package ChecklistProduct Features Product Specifications Serial Communication Parameters Advanced Built-in FeaturesSoftware Features Power RequirementsGetting Started ‰ Panel Layout ‰ Connecting the HardwareFront panel of NPort 5600 series Rear panel of NPort 5600 series AC PowerRear panel of NPort 5600 series DC Power Panel LayoutConnecting NPort 5610-16/8-48V’s Power Connecting the HardwareWiring Requirements Connecting NPort 5610/30/50-16/8’s PowerGrounding NPort 5610-16/8-48V Connecting to the NetworkAdjustable Termination Resistor for the RS-485 Port Connecting to a Serial DeviceLED Indicators Link Indicator on the Rear Panel of NPort 5650 Fiber ModelNPort 5650 DIP Switches Initial IP Address Configuration LCM Display Factory Default IP AddressDefault IP address Initializing NPort’s IP AddressDetailed Menu Options Button Name ActionLevel ARP NPort Administration SuiteTelnet Console NPort 5600 Series User’s Manual NPort 5600 Series User’s Manual NPort 5600 Series User’s Manual Choosing the Proper Operation Mode Real COM Mode Real COM ModeTCP Server Mode TCP Server ModePair Connection Mode TCP Client ModeUDP Mode RFC2217 Mode Reverse Telnet ModeDisabled Mode PPP Mode Web Console Configuration Opening Your Browser Basic Settings Local time TimeServer name Time zoneConsole Network SettingsGateway IP ConfigurationIP Address NetmaskContact Snmp SettingsDNS server 1 / DNS server Community nameAuto report period IP Address ReportAuto report to IP Auto report to TCP portPort alias Serial SettingsSerial Parameters TCP alive check time Operating SettingsReal COM Mode Setting Factory Default Necessity To 99 min Min OptionalIgnore jammed IP Max connection Setting Factory Default Necessity RequiredMax. connection Max connection 2 toForce transmit Packing length Setting Factory Default Necessity RequiredDelimiter Delimiter processTCP Server Mode Max connection Packing length Local TCP port Setting Factory Default Necessity 4001 RequiredCommand port Setting Factory Default Necessity 966 OptionalInactivity time TCP Client ModeIgnore jammed IP Delimiter process Connection control Destination IP addressDestination IP address 2/3/4 Designated Local Port 1/2/3/4Connect/Disconnect Description UDP Mode Force transmit Setting Factory Default Necessity To 99 min Min Required Pair Connection ModePair Connection Master Mode Blank Pair Connection Slave ModeMap CR-LF Reverse Telnet ModeSetting Factory Default Necessity To 99 min Optional RFC2217 Mode Disabled ModeSetting Factory Default Necessity To FF hex None Optional Packing length Setting Factory Default Necessity OptionalTCP/IP compression PPP ModeSetting Factory Default Necessity Yes or No Optional Modem Initial stream Accessible IP SettingsSource IP address IP netmaskAllowable Hosts Input format Hosts on a specific subnet can access the NPortAny host can access the NPort PPP User TableMail Server Auto Warning SettingsAuto warning E-mail and Snmp Trap Snmp Trap Server Event TypeMail Setting Factory Default Necessity Enable, Disable OptionalDCD changed DSR changedMonitor Async MonitorMonitor Line Monitor Async-Settings Change PasswordLoad Factory Defaults ‰ Overview ‰ Installing NPort Administrator ‰ Configuration Configuring NPort AdministratorInstalling NPort Administrator NPort 5600 Series User’s Manual IP Serial LIB NPort 5600 Series User’s Manual IP Serial LIB Configuration Broadcast Search Unlock Password Protection NPort 5600 Series User’s Manual IP Serial LIB Fixed LockUnlock BlankConfiguring NPort NPort 5600 Series User’s Manual IP Serial LIB Upgrading Firmware Export/Import Add Target Æ Select target from the list Select Add Target NPort 5600 Series User’s Manual IP Serial LIB NPort 5600 Series User’s Manual IP Serial LIB NPort 5600 Series User’s Manual IP Serial LIB NPort 5600 Series User’s Manual IP Serial LIB COM Mapping Port MonitorOn-line COM Mapping NPort 5600 Series User’s Manual IP Serial LIB Fast Flush only flush local buffer NPort 5600 Series User’s Manual IP Serial LIB Off-line COM Mapping IP Location NPort 5600 Series User’s Manual IP Serial LIB IP Serial LIB How to install IP Serial Library? What is IP Serial Library?Why Use IP Serial Library? Port Control Input/Output Data Port Status Miscellaneous IP Serial LIB Function GroupsExample Program Server Control‰ Cable Wiring Diagrams Pinouts and Cable WiringSerial Port Pinouts Port Pinout DiagramsEthernet Port Pinouts Serial Cables for NPort 5610/5650 RS-232 Cable Wiring DiagramsRJ45 8-pins to Female DB9 Ethernet CablesRJ45 8-pins to Female DB25 RJ45 8-pins to Male DB9RJ45 8-pins to Female DB25 Serial Cables for NPort 5630 RS-422/4-wire RS-485NPort 5600 Series User’s Manual Well Known Port Numbers Serial Cables for NPort 5630 2-wire RS-485Serial Cables for NPort 5650 RS-422/4-wire RS-485 RJ45 8-pins to Male DB25 Serial Cables for NPort 5650 2-wire RS-485Pin Assignments for DB9 Male and Female Connectors Pin Assignments for DB9 and DB25 ConnectorsPin Assignments for DB25 Male and Female Connectors Well Known Port Numbers TCP Socket Application ServiceSnmp Agent with MIB II & RS-232 Like Group UDP Socket Application ServiceSnmp Agent with MIB II & RS-232 Like Group Address Translation MIB System MIB Interfaces MIBInput Signal Table Output Signal Table Auto IP Report Protocol AP ID & Hardware ID Mapping Table Auto IP Report FormatInfo n ID ListService Information Following services are provided Moxa Internet ServicesSerial Number Problem Report FormMoxa Product Product Return Procedure