Q-Logic QLA22XX manual Installation Help

Page 14

Installation Help

2 – Hardware Installation

10.Power up all external FC devices, then power up the PC and observe the monitor. The BIOS is disabled by default. Consequently, the devices attached to the QLA22xx board are not identified. For example:

QLogic Corporation

QLA22xx PCI Fibre Channel ROM BIOS Version X.XX

Copyright (C) QLogic Corporation 2000 All rights reserved. www.qlogic.com

Press <Alt-Q> for Fast!UTIL

BIOS for Adapter 0 is disabled

ROM BIOS not installed

NOTE:

Sun SPARC systems do not display the BIOS banner.

Enable the BIOS only if the boot device is attached to the QLA22xx board.

For further information about enabling the QLA22xx BIOS, see appendix A.

If the information displayed on your monitor is correct, congratulations! You have successfully installed the QLA22xx board in your computer.

See the appropriate QLogic software installation guide for detailed instructions on how to install the software drivers.

If the information displayed is not correct and you have checked the QLA22xx board’s configuration, see section 3 for troubleshooting information.

2.5

Installation Help

If your system has an integrated drive electronics (IDE) fixed disk device, it may be assigned device number 80, which is the boot device. If your system does not have an IDE disk device, the first bootable FC disk device configured (the one with the lowest ID) is assigned device number 80 and becomes the boot device. The QLA22xx BIOS must be enabled if the boot device is connected to the QLA22xx.

If you have a selectable boot BIOS, set the motherboard BIOS parameters to None or Not Installed. The ROM BIOS on the FC controller automatically configures the FC peripherals.

2-8

FC0151103-00 E

Image 14
Contents Hardware Installation Guide for QLA22xx Board Family QLogic Corporation Table of Contents Figures Introduction General DescriptionWhat is Fibre Channel? FeaturesPreinstallation Procedures What You Need for InstallationQLA2200 Board Layout QLA2202F Board Layout QLA2204F Board Layout QLA2200G Board Layout Power Distribution Installation in the ComputerFC0151103-00 E Installation Help System Configuration Problem Checklist Problems After InstallationHardware Problem Checklist Fibre Channel Problem Checklist Configuration Settings IntroductionTable A-1. Host Adapter Settings Host Adapter SettingsSelectable Boot Settings Table A-2. Advanced Adapter Settings Restore Default SettingsAdvanced Adapter Settings Raw Nvram DataConfiguration Settings Fast!UTIL Extended Firmware Settings Table A-3. Extended Firmware SettingsTable A-4. RIO Operation Modes Table A-5. Connection OptionsSelect Host Adapter Scan Fibre Channel DevicesFibre Disk Utility Select Host Adapter Fast!UTIL FC0151103-00 E Table B-2. QLA22xx Board Specifications Table B-1. QLA22xx Board Operating EnvironmentOptic support available using an external MIA

QLA22XX specifications

The Q-Logic QLA22XX series encompasses a range of high-performance Fibre Channel Host Bus Adapters (HBAs) designed to enhance data storage and network connectivity within enterprise environments. Specifically, these adapters are tailored for environments requiring robust storage solutions, ensuring that organizations can effectively manage their data traffic and optimize their storage strategies.

At the heart of the QLA22XX is its adherence to the Fibre Channel standard, which allows for high-speed connections between servers and storage devices. These adapters support speeds of up to 16 Gbps, which provides the bandwidth necessary for handling multiple workloads simultaneously. This capability is crucial for businesses that rely on rapid access to large volumes of data, thereby facilitating quicker decision-making processes and enhancing productivity.

The QLA22XX series features advanced technologies such as enhanced error correction and adaptive routing. These technologies ensure data integrity and reliability during transfer, reducing the likelihood of data corruption. Additionally, the adaptiveness of the routing capabilities allows the HBA to optimize performance by dynamically adjusting to various network conditions and topologies.

Another key characteristic of the QLA22XX is its compatibility with a multitude of operating systems, including major platforms like Windows, Linux, and VMware. This broad compatibility simplifies deployment across diverse IT ecosystems, making it easier for organizations to integrate these HBAs without extensive modifications to their existing infrastructure.

Moreover, the QLA22XX series supports the latest management and monitoring tools, enabling administrators to have complete visibility into performance metrics and potential issues. This includes support for the SNMP protocol, which facilitates proactive monitoring and management of the networked storage systems.

Energy efficiency is also a consideration in the design of the QLA22XX series. These adapters are engineered to minimize power consumption, which not only aids in reducing operational costs but also contributes to the organization's sustainability goals.

In summary, the Q-Logic QLA22XX series is a reliable and high-performance Fibre Channel HBA solution. With its high-speed connectivity, advanced technologies for data integrity, broad compatibility, and proactive management features, it stands out as a robust option for enterprises looking to enhance their data storage and network connectivity capabilities.