Moxa Technologies CA-132/132I user manual Overview, Package Checklist, Product Features

Page 6

Overview

CA-132/132I is a PC/104 module that supports the RS-422/485 serial interfaces, and can be used with PC/104 CPU modules or CPU cards that accept PC/104 expansion modules. CA-132/132I has two independent serial interfaces, which are accessed through RJ45 connectors. You can configure both ports for the RS-422 or RS-485 interfaces by DIP switch. The module’s industry-standard MOXA UART (16C550 compatible) is fully programmable. Moxa has implemented its patented ADDC™ technology for RS-485 automatic direction control, so there is no need to change jumpers to switch the module between driver and receiver. The built-in 16 KV ESD surge protection protects other devices connected to the RS-485 network.

Package Checklist

MOXA CA-132/132I products are shipped with the following items:

!1 MOXA CA-132/132I 2-port serial board

!CA-132/132I Document & Software CD

!CA-132/132I Quick Installation Guide

NOTE: Notify your sales representative if any of the above items is missing or damaged.

Product Features

CA-132/132I Series products enjoy the following features:

!2 RS-422/485 ports

!RS-422/485 communication distance up to 4000 feet (1.2 km)

!High speed data transmission rate up to 230.4 Kbps

!Switch selectable for I/O and INT Vector addresses (from Hex 000 to 3FF)

!64-byte FIFOs

!IRQ settings are selectable by jumper

!Built-in 16 KV ESD surge protection for TX and RX lines

!4 LED indicators onboard (red for TX, and green for RX)

!Support 4-wire RS-422 and 2/4-wire RS-485

!ADDC™ for RS-485 transmission

!CA-132I has 2 KV isolation protection

Product Specifications

CA-132/132I Series boards have the following specifications:

!Dimensions: 9.6 cm × 9.0 cm

!Bus: PC/104

!Baud rate: 50 to 230.4 Kbps

!Character length: 5, 6, 7, or 8 bits

!Parity: even, odd, none, mark, and space

!Stop bit: 1, 1.5 or 2

!I/O connectors: dual 8-pin RJ-45 connectors

!Interrupt levels: IRQ 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15

!Clock input: 14.745 MHz

!Power consumption (+5 V): CA-132/210 mA, CA-132I/455 mA

!MTBF: 100,000 hrs @ 25environment

!Operating temperature: 0 to 55

1-2 CA-132/132I User’s Manual

Image 6
Contents CA-132/132I User’s Manual Third Edition, NovemberCopyright Notice TrademarksDisclaimer Page Table of Contents Introduction Product Specifications Package ChecklistProduct Features OverviewIntroduction Page Hardware Installation Hardware Installation Block Diagram of CA-132/132IRS-422/485 Interface Settings Base Address & Interrupt Vector SettingsCA-132/132I User’s Manual IRQ Setting Initial InspectionAsync Port 4-wire RS-422/4-wire 485 Pin Assignment RJ45 Async Port 2-wire RS-485 Pin Assignment RJ45RS-422/485 Pin Assignments Software Installation Installing the driver Windows NTSoftware Installation CA-132/132I User’s Manual Removing a CA-132/132I serial board Windows 2000/XP/2003 Software Installation CA-132/132I User’s Manual Software Installation 10 CA-132/132I User’s Manual Software Installation 12 CA-132/132I User’s Manual Software Installation Disabling the device Software Installation Uninstalling the device Windows 95/98/MESoftware Installation 18 CA-132/132I User’s Manual Software Installation Removing the device Uninstalling the driver Installing Driver DOSDriver Setup 24 CA-132/132I User’s Manual Port number TxD buffer size RxD buffer size F5 Group Edit Loading Driver Unloading DriverSerial Programming Tool PComm Programming Library PComm InstallationDiagnostic for Moxa boards only UtilitiesMonitor for Moxa boards under Windows NT Only Terminal EmulatorBy RTS Mode For back-compatibility How to transmit and receive data for Windows NT, 95/98RS-485 Programming Service Information Moxa Internet Services Following services are providedProblem Report Form Moxa CA-132/132I SeriesProduct Return Procedure Revision History Document Edition Revision Date Revision Details