Moxa Technologies CP-168U user manual Moxa PComm Utility, Event Log

Page 36

4.Select an Rx FIFO Trigger from the Rx FIFO Level pull-down list. Rx FIFO trigger levels from High to Low are available, with a default value is High Level (120 bytes). Check Set the change to all ports check-box to apply the just defined Rx FIFO Trigger to all ports.

5.Select a Tx FIFO Size from the Tx FIFO Level pull-down list. Tx FIFO Level from High to Low are available, with a default value is High Level (128 bytes). Check Set the change to all ports check-box to apply the just defined Tx FIFO Size to all ports.

 

CP-168U v2

CP-168U v1

 

Tx FIFO

Rx FIFO

Tx FIFO

Rx FIFO

High

128

120

64

56

Middle

64

60

32

28

Low

1

1

1

1

Unit: Bytes

6.Click on OK in the Port X dialog box to confirm the port settings, and then click on OK in the Property dialog box to complete the port settings.

MOXA PComm Utility

This utility, which comes with MOXA PComm Lite, provides a convenient way to diagnose problems with Moxa boards, and provides internal and external testing of IRQ, TxD/RxD, UART, CTS/RTS, DTR/DSR, etc. This program can verify the correct operation of both the H/W and S/W for all Moxa boards and ports.

Event Log

To check the Event Log for MOXA boards, click Start " Settings " Control Panel " Administrative Tools " Event Viewer, to enter the Event Viewer program. You may find the latest information relevant to the Moxa driver in the system category.

3-20 Smartio CP-168U User’s Manual

Image 36
Contents Smartio CP-168U User’s Manual Page Copyright Notice TrademarksDisclaimer Page Moxa Internet Services Page Table of Contents Introduction OverviewPCI Solution Surge ProtectionOperating System Support Moxa Serial Comm Tool Features Package Checklist 136.9 × 100 mm 5.39 × 3.94 in CP-168U Installation Guide InstallationPage Hardware Installation Installing the Smartio CP-168U boardSmartio CP-168U User’s Manual Software Installation WindowsInstalling the Driver Software Installation Smartio CP-168U User’s Manual Software Installation How to Check the Installation Using Device ManagerPort Configuration Smartio CP-168U User’s Manual Using PComm Using Event Log Windows 2000/XPPlay devices Click on Next to continue Smartio CP-168U User’s Manual Software Installation Smartio CP-168U User’s Manual Software Installation Smartio CP-168U User’s Manual Device Manager Port Configuration Software Installation Moxa PComm Utility Event LogRemoving the Driver Click on OK to proceed with the un-installation of the board Windows 95/98 Installing the Driver First Time Driver Installation Windows Software Installation Board and Port Ready Configuring the Board and Ports Smartio CP-168U User’s Manual Updating the Driver Removing the Driver Windows NT Installing the Driver Software Installation Smartio CP-168U User’s Manual Smartio CP-168U User’s Manual Software Installation Smartio CP-168U User’s Manual Configuring the Board and Ports Re-Configuring Port SettingsConfiguring Another CP-168U Board Removing an Existing CP-168U Board Configuration Removing the Driver DOS Setting up the Driver Software Installation Port number TxD buffer sizeRxD buffer size F5 Group EditLinux SCO Smartio CP-168U User’s Manual Bus/Dev No Smartio CP-168U User’s Manual Software Installation Page PComm Installation Serial Programming ToolsPComm Programming Library Diagnostic for Moxa boards only UtilitiesMonitor for Moxa boards under Windows NT/2000/XP/2003 Terminal Emulator Connection Cables and Cable Wiring RS-232 Cable WiringDB62 Female Connector Pinouts DB-9/M Pin Assignment Opt8-M9, Opt8D DB-25/M Pin Assignment Opt8B/CDB-25/F Pin Assignment Opt8A/S RJ45 Pin Assignment Opt8-RJ45DB-25/F Pin Assignment Opt8F/Z DB-25/F Pin Assignment Opt8KTroubleshooting General TroubleshootingWindows NT system panics blue screen Troubleshooting Page Specifications Technical ReferenceMoxa Uart Return Procedure Revision History
Related manuals
Manual 63 pages 28.34 Kb