Sun Microsystems 5000, 4000, 6000 manual Powering Off the System

Page 61

3

3.3.4 Powering Off the System

Before turning off the system power, you must halt the operating system. See the Preface, “UNIX Commands,” to find references if you need help with the commands for this task or other system administration procedures.

Note – Failure to halt the operating system properly can cause the loss of disk drive data.

Note – Do not disconnect the terminal while the system is running.

Caution – To avoid damaging internal circuits, do not disconnect or plug in any cable while power is applied to the system.

To shut down the system:

1.Notify users that the system is going down.

2.Back up the system files and data to tape, if necessary.

3.Halt the system using the appropriate commands. Refer to the Solaris Handbook for SMCC Peripherals that corresponds to your operating system.

4.Wait for the system-halted message and the boot monitor prompt.

5.Turn the key switch on the front panel of the server to the Standby position (fully counterclockwise).

6.Turn off the system power in this order:

a.External drives and expansion cabinets (if any)

b.System AC power switch

c.Terminal

For more system administration information on methods for shut-down and backup, see the Preface, “UNIX Commands,” for references to documentation that describes these procedures.

Powering the System On and Off

3-15

Image 61
Contents Ultra Enterprise 6000/5000/4000 Systems Installation Guide Please Recycle Contents Cabling the System Using the Software Page Figures Viii Tables Page Preface Unix CommandsShell Prompts Typographic ConventionsOrdering Sun Documents Related DocumentsSun Welcomes Your Comments Preface Xvi Preparing for Installation Enterprise 6000/5000 systems 16-slot Remove the sides of the container Unpacking the Enterprise 6000/5000 Cabinet Systems2Attaching the Ramps to the Shipping Pallet Shipping and Storing the SystemEnterprise 6000/5000 Cabinet Systems Preparing the Electrical Circuits4IEC 309 Electrical Connector Preparing the Ethernet Network Preparing the Air ConditioningEnterprise 4000 System 5Types of Network Cables Used Floorspace for the Enterprise 6000/5000 Cabinet Systems Preparing the AreaSurface for the Enterprise 4000 System 7Cabinet Server Access Areas Top ViewMoving the Server Preparing the Enterprise 6000/5000 Cabinet Systems9Moving the Server Safely Down the Ramps Adjusting the Levelling PadsLevelling pad 1 Rear screen Kick panel 11Stabilizer Bar Preparing the Enterprise 4000 SystemRemove the top front bezel Using the User Naming AreaPage Preparing the System for Cabling Cabling the SystemStandby position Replacing the Rear Screen and Kick Panel Connecting the Enterprise 6000/5000 System Power Cord Connecting the Power Cords4Key Switch Positions Connecting the Enterprise 4000 System Power Cord5AC Power Switch and Power Receptacle Connecting the Network Cable to the System710/100BASE-T Ethernet Connection Connecting the System to the NetworkShows the elements used in the installation process Lists the cabling limitations for Ethernet 10 Clock Board Connecting an Ascii TerminalConnecting the Fiber Cable to the I/O Board Connecting External Scsi Devices Location Internal Length Comments Use tie wraps to secure the cable to the left mounting rail Using JumpStart Automatic Installation Powering the System On and OffEnterprise 6000/5000 Cabinet Systems Powering On the SystemTurn on power to any expansion cabinets 2The AC Power Sequencer Power Switch Turn the key switch to the On position Watch the terminal screen for any firmware error messages 4CPU Reset Switch on the Clock Board Reading Boot MessagesSummarizes LED status indications Interpreting Status LED PatternsPowering Off the System Enterprise 4000 System 6Key Switch Positions and AC Power Switch 7CPU Reset Switch on Clock Board Reading Boot Messages DC power green Fault yellow Powering Off the System Failure of Network Communications Description of the ProblemSolution Page Operating System Software Using the SoftwareSolstice SyMON Software Page Index-1 IndexPost Scsi Index-4 Reader Comment Card
Related manuals
Manual 334 pages 12.65 Kb Manual 28 pages 54.7 Kb Manual 204 pages 20.18 Kb

4000, 5000, 6000 specifications

Sun Microsystems, a pivotal player in the computing industry during the late 20th and early 21st centuries, was renowned for its innovative hardware and software solutions. Among its notable offerings were the Sun-6000, Sun-5000, and Sun-4000 series, powerful workstations and servers designed for a range of enterprise-level applications.

The Sun-6000 series, introduced in the early 1990s, marked a significant advancement in computing performance. These systems were built on the SPARC architecture, which facilitated high levels of processing power and multitasking capabilities. One of the main features of the 6000 series was its scalability, allowing organizations to increase their processing power by adding more modules. It also offered robust graphics performance, making it ideal for scientific visualization and complex data analysis.

Next in line was the Sun-5000 series. Launched shortly after the 6000 series, the 5000 line was celebrated for its reliability and ease of management. This series emphasized a balanced architecture, which combined processing capabilities with ample memory and storage options. Key characteristics included support for multiple processors, leading to improved performance for demanding applications. Additionally, the 5000 systems featured advanced input/output capabilities, ensuring fast data transfers—crucial for database applications and web servers.

Finally, the Sun-4000 series targeted businesses seeking affordable yet potent computing solutions. These servers boasted a modular design, allowing for easy upgrades and maintenance. The 4000 series was particularly notable for its support for various operating systems, including SunOS and Solaris. These systems were engineered to handle a range of workloads, from enterprise resource planning to web hosting, while still fitting into a value-driven budget.

Across all three series, Sun Microsystems prioritized compatibility and integration, ensuring that each system offered seamless connectivity with Sun's software solutions and third-party applications. Their commitment to open standards and interoperability set them apart in the competitive landscape of enterprise computing. Additionally, the use of high-quality components lent the systems durability, making them a wise investment for organizations looking to future-proof their IT infrastructure.

In summary, the Sun-6000, 5000, and 4000 series exemplified Sun Microsystems' ethos of innovation and reliability. These powerful systems catered to diverse business needs, setting benchmarks in performance and functionality that continue to influence modern computing.