Sun Microsystems X6240 manual Configuring the Ilom IP Address, To see only the IP address, type

Page 35

Configuring the ILOM IP Address

This section describes how to view and set the ILOM IP address. It includes the following sections:

■“To View the ILOM IP Address” on page 23

■“To Configure the ILOM IP Address Using BIOS Setup Utility” on page 23

■“To Configure the ILOM IP Address Using DHCP” on page 25

■“To Configure the ILOM IP Address Using the CLI” on page 26

▼To View the ILOM IP Address

1.Log in to the ILOM CLI using any of the methods described in “Connecting to the Server Module ILOM” on page 13.

To use the Ethernet SSH connection, you must already know the IP address.

2.Type these commands from the root directory.

a.To see all the IP address-related information, type:

-> show /SP/network

b.To see only the IP address, type:

-> show /SP/network/ipaddress

▼To Configure the ILOM IP Address Using BIOS Setup Utility

The BIOS Setup Utility enables you to set the ILOM IP address. You can configure the IP address manually (static) or use DHCP to configure it.

1. Verify the following:

■Your DHCP server is configured to accept new media access control (MAC) addresses.

■Your DHCP server is connected to either the corresponding NEM port or the RJ-45 NET MGT Ethernet port.

2.Start the BIOS Setup Utility.

a.Boot the system.

b.Watch the boot messages. You will see a message that says you can press F2 to enter BIOS setup.

Chapter 2 Setting Up the Server Software

23

Image 35

Contents Sun Blade Server Module Installation Guide Please Recycle Contents Configuring the Preinstalled Solaris 10 Operating System Index Vi Sun Blade X6240 Server Module Installation Guide June Preface Using Unix CommandsRelated Documentation Shell PromptsTypographic Conventions Preface Third-Party Web Sites Product UpdatesSupport, and Training Sun Welcomes Your Comments Xii Sun Blade X6240 Server Module Installation Guide June Installation Overview and Terms Setting Up the Server HardwareInserting the Server Module See Powering On and Powering Off the Server Module onTo Insert the Server Module 1Inserting the Server Module Into the Chassis Verify that standby power is on Powering On and Powering Off the Server ModuleTo Power on Main Power for All Server Module Components 2Sun Blade X6240 Server Module Front Panel To Shut Down Main Power Mode To Use a Dongle Cable for Testing Using a Dongle Cable for Testing3Dongle Cable Connections Sun Blade X6240 Server Module Installation Guide June Integrated Lights Out Manager Setting Up the Server SoftwareUser name root Password changeme What Is a Service Processor?About the Preconfigured Administrator Account Ilom Connection Overview Connecting to the Server Module IlomTo Connect to Ilom Through the Chassis Serial Connector 1Serial Management Port Pinouts Press Enter on the terminal deviceType exit when you are done Navigate to the server module Ilom by typing this commandType the command start Type y to continue or n to cancelFollowing display shows an example of the login screen 2Dongle Cable Option 2 Connecting to Ilom Through a Dongle CableWhen you are done, exit Ilom by typing Option 3 Connecting to Ilom Through the Ethernet PortType the user name and password when prompted To log out of ILOM, type exit Type your password when promptedLogging In and Out of Ilom Click Log Type your user name and password4ILOM Log Out Screen Verify the following Configuring the Ilom IP AddressTo see only the IP address, type Select Commit to save your changes After you see the message, press F2To Configure the Ilom IP Address Using Dhcp To navigate to /SP/network, type Type the reset commandTo log out of ILOM, type Do one of the followingIf you logged in using SSH, you will be Setting Up Platform Operating System and Driver Software Sun Blade X6240 Server Module Installation Guide June Configuring the Preinstalled Solaris 10 Operating System Before You Begin Installation Worksheet1Worksheet for Solaris 10 Configuration NIS DNS Ldap 1Worksheet for Solaris 10 Configuration To Configure the Preinstalled Solaris 10 OS Configuring the Preinstalled Solaris 10 Operating SystemWhen the prompt appears, type y Start the serial console mode by entering the followingTo Redirect the Console Output to the Video Port Optional RAID Drive Overview Configuring X6240 Server Module RAID DrivesRAID Drive Options Mirroring the Preinstalled Solaris OS with LSI RAIDTo Create a Mirror Image of the Preinstalled Solaris OS Using your Solaris server, log in and start Xserver Solaris 10 User Documentation Solaris 10 Operating System User InformationSun Studio Using the Solaris Installation ProgramSolaris 10 OS Training Sun Java Enterprise SystemDownloading Software Reinstalling the Solaris Operating SystemSun Blade X6240 Server Module Installation Guide June A P T E R Hardware and Software Prerequisites Reset the server module, for example Initial Setup of Preinstalled Windows Server 2003 R2 OSTo Perform the Initial Setup of the Preinstalled Windows OS Windows Setup Screen Name Action Required RAID Drive Overview 2shows the RAID drive options Mirroring the Preinstalled Windows OS with LSI RAIDTo Create a Mirror Image of the Preinstalled Windows OS Cdrom drive\RAIDmgmt\StorageTEK\Windows\3264bit\ Click on the SUN STK RAID Controller Sun Link Important Information2Sun Supplemental Software Recovery Media KitSun Blade X6240 Server Module Installation Guide June Index Sun Blade X6240 Server Module Installation Guide June