Paradyne 8820 PdnMgmtIpAddress RW, PdnMgmtIpNetMask RW, PdnMgmtIpEthGateway RW, PdnMgmtBootVpi RW

Page 80

1. Network Management Specification

7.6.1.2pdnMgmtIpAddress (RW).

The IP address assigned to this port. If the pdnMgmtIpConfigMode is set to modes other than ’manual’, then the MAX-ACCESS for this object is read-only and the value of the object represents the actual IP address assigned to the port by the DHCP client (or 0.0.0.0, if none assigned). Changes to this object could disrupt data flow through the port.

7.6.1.3pdnMgmtIpNetMask (RW).

The IP subnet mask assigned to this port.

The MAX-ACCESS for this object behaves the same as the pdnMgmtIpAddress explained above. Changes to this object could disrupt data flow through the port.

7.6.1.4pdnMgmtIpEthGateway (RW).

The IP Gateway for an ethernet based IP port.

This object is supported only on IP ports that are configured to run over ethernet type of media. This object would be set to 0.0.0.0 for other types of interfaces and is not valid.

7.6.1.5pdnMgmtIpPhysAddress (RW).

The physical address associated with the media.

For IP Ports with Ethernet type of media, the MAX-ACCESS for this object is restricted to read-only. In such cases, this object would reflect the MAC address of the underlying ethernet data link. For IP Ports that run over ATM PVCs, this object is writable.

7.6.1.6pdnMgmtIpConfigMode (RW).

The IP configuration mode for the port. The possible values are: manual(1), dhcp(2).

In “manual” mode, it is up to the user to provide the IP address and IP subnet mask of the port.

In “dhcp” mode, the respective protocols are resposible to obtain and populate the IP address and IP subnet mask for the port. The default value for all the interfaces is dhcp(2).

Whenever the config mode is changed from “manual” mode, the IP address and the IP subnet mask for the port would automatically be reset to 0.0.0.0. External Manager stations SHOULD NOT attempt to write the IP address or the IP subnet mask of the port when this object is not in “manual” mode.

7.6.1.7pdnMgmtBootIfIndex (RW)

The interface index of the ATM interface to be used by the DHCP client, if the pdnMgmtIpConfigMode is set to “dhcp” respectively. For the Ethernet’s IP port, this object is 0.

7.6.1.8pdnMgmtBootVpi (RW)

The VPI of the ATM PVC to be used by the DHCP client, if the pdnMgmtIpConfigMode is set to “dhcp” respectively.

7.6.1.9pdnMgmtBootVci (RW)

The VCI of the ATM PVC to be used by the DHCP client, if the pdnMgmtIpConfigMode is set to “dhcp” respectively.

7.6.1.10pdnMgmtIpAdminStatus (RW)

The status of the IP Port (interface). Possible values are up(1), down(2).

74

June 2003

8000-A2-GB30-00

Page 79 Page 81
Image 80
Page 79 Page 81
Contents Hotwire 8620 Copyright 2003 Paradyne Corporation All rights reserved Contents Contents June About This Guide Section DescriptionProduct-Related Documents Document Number Document TitleName Description GranDSLAM 3.0 Network Management InterfaceSupported RFCs and MIBs 1 Supported RFCs and MIBs 2 Supported RFCs and MIBs 3 IMA MIBSupported RFCs and MIBs 4 PDN-ENTITY-REDUNDANCY-MIBSupported RFCs and MIBs 5 PDN-DS1EXT-MIBOther Supported RFCs Used as Guidelines for Implementation Name/DescriptionStandards Compliance for Snmp Traps Summary of Traps 1 Description VarBinds Standard TrapsDSX Traps ATM-M4 TrapsShdsl MIB Traps Summary of Traps 2 Description VarBindsEntity MIB Traps Summary of Traps 3 Description VarBinds Enterprise Specific Traps Summary of Traps 4 Description VarBindsSonet Linear APS MIB Traps Adsl Specific Traps Summary of Traps 5 Description VarBindsSummary of Traps 6 Description VarBinds IMA Traps Summary of Traps 7 Description VarBindsStandards Compliance to Snmp MIBs GranDSLAM Interfaces SysDescr Object system Management Information Base MIB-II RFCSystem Group, MIB-II RFC SysServices Object system SysServices Layer L Functionality Value2L-1 SumSysObjectID Object system SysUpTime Object systemEvolution of the Interfaces Group of MIB-II RFC IfNumber Object interfacesIfIndex Object ifEntry IfIndex schemeGranDSLAM 3.0 Interface List Layer Supported Maximum IfName Interface indexes ifIndex IfIndex Assignments IfDescr Object ifEntryIfType Object ifEntry IfMtu Object ifEntryIfMtu Interface IfMtuIfAdminStatus Object ifEntry IfSpeed Object ifEntryIfSpeed Interface IfSpeedIfAdminStatus Interface IfAdminStatusIfOperStatus Object ifEntry IfOperStatusIfLastChange Object ifEntry IfInUcastPkts Object ifEntry 14. ifInUncastPkts Interface IfInUncastPkts Object ifEntry 15. ifInUncastPkts InterfaceIfInErrors Object ifEntry 17. ifInErrors Interface IfInDiscards Object ifEntry 16. ifInDiscards InterfaceETH1 IMA IfOutUcastPkts Object ifEntry 20. ifOutUcastPkts Interface IfOutNUcasts Object ifEntry InterfaceIfOutQLen ifEntry IfOutErrors Object ifEntry InterfaceIfOutDiscards Object ifEntry 22. ifOutDiscards Interface IfLinkUpDownTrapEnable Object ifXEntry IfSpecific ifEntryExtension to the Intf. Table ifXTable RFC 24. Extension to the Interface TableInterface Stack Group RFC IfStackHigherLayer Object ifStackEntryIfStackLowerLayer Object ifStackEntry IfStackStatus Object ifStackEntryTransmission Group, MIB-II RFC 1213 Supported Snmp Group, MIB-II RFCNetwork Management Specification Physical Layer Adsl MIB RFC 28. Adsl MIB Comments Paradyne ReachDSL MIB pdnreachDSL.mib 30. ReachDSL MIB CommentsDS1 MIB RFC 31. DS1 MIB Comments Paradyne DS1-EXT MIB PDN-DS1EXT-MIBPdnDs1ExtConfConnector RW 32. DS1-EXT MIB CommentsPdnDs1ExtConfLineLengthType RW PdnDs1ExtConfLineLength RWSONET-MIB RFC 33. SONET-MIB Comments SonetMediumEntry 34. sonetMediumEntry CommentsSonetSESthresholdSet SonetPathCurrentWidthDevSonetStatusChangeTrapEnable By default, this object is enabledDevSonetXmitClkSrc DevSonetStatusLastChangeNewSpectrumMgmtGeneralConfigEntry 36. Shdsl MIB CommentsSpectrum Management pdnspectrummgmt.mib 37. Spectrum Management CommentsATM Interface Configuration Parameter Group RFC Link Layer ATM AtoM MIB RFC38. ATM MIB Comments AtmInterfaceMaxVpcs Object atmInterfaceConfEntryAtmInterfaceMaxVccs Object atmInterfaceConfEntry 40. atmInterfaceMaxVccsAtmInterfaceMaxVccs AtmInterfaceConfVpcs Object atmInterfaceConfEntryAtmInterfaceIlmiVpi Access AtmInterfaceIlmiVci AccessAtmInterfaceMaxActiveVciBits Object atmInterfaceConfEntry AtmInterfaceMaxActiveVciBitsAtmInterfaceMyNeighborIpAddress Access AtmInterfaceMyNeighborIfName AccessAtmInterfaceMyNeighborIfName Object atmInterfaceConfEntry AtmInterfaceCurrentMaxVpiBits Object atmInterfaceConfEntryAtmInterfaceTCAlarmState Object atmInterfaceTCEntry AtmInterfaceCurrentMaxVciBits Object atmInterfaceConfEntryAtmInterfaceSubscrAddress Object atmInterfaceConfEntry AtmInterfaceSubscrAddressAtmServiceCategory Object atmTrafficDescrParamEntry Virtual Channel Link VCL Configuration Group RFCATM Traffic Descriptor Group RFC 54. Traffic Descriptor TypesAtmVclOperStatus Object atmVclEntry AtmVclLastChange Object atmVclEntryAtmVccAalType Object atmVclEntry AtmVccAal5CpcsTransmitSduSize Object atmVclEntryVirtual Channel Cross Connect Group RFC AtmVcCrossConnectRowStatus Object atmVcCrossConnectEntryAtmfM4TcAlarmSeverityIndexObject atmfM4TcAdapterEntry AtmfM4MIB- Snmp M4 Network Element View MIB atmfM4MIB55. Object Supported in ATM Forum MIB Type TC Adapter Layer Table atmfM4TcAdapterEntryAtmfM4VcXConnRecover Object atmfM4VcXConnEntry1 ATM Cell Layer Table atmfM4ATMLayerEntryAtmfM4IfType Object atmfM4ATMLayerEntry AtmfM4IfSubscriberAddress Object atmfM4ATMLayerEntry56. Paradyne Extensions to ATM MIBs 1 Sup Object Type Ported ATM Loopback 57. ATM Loopback CommentsGoto tryagain IMA MIB AF-PHY-0086.001 58. IMA MIB Object Syntax Access Status Ported Entity MIB version 2 Objects supportedEntityPhysical Group 59. entPhysicalEntry entPhysicalTable 1 1 Sup Object59. entPhysicalEntry entPhysicalTable 1 2 Sup Object EntPhysicalIndex60. entPhysicalIndex Entity Comments EntPhysicalDescr61. entPhysicalDescr Entity Description EntPhysicalVendorType63. entPhysicalVendorType 1 Entity EntPhysicalVendorType 64. entPhysicalContainedIn Entity EntPhysicalContainIn 63. entPhysicalVendorType 2 Entity EntPhysicalVendorTypeEntPhysicalContainedIn EntPhysicalParentRelPos EntPhysicalClass65. entPhysicalClass Entity EntPhysicalClass EntPhysicalHardwareRev EntPhysicalName67. entPhysicalName Entity EntPhysicalName 68. entPhysicalHardwareRev Entity EntPhysicalHardwareRev EntPhysicalSoftwareRevEntPhysicalFirmwareRev 69. entPhysicalFirmwareRev 1 Entity EntPhysicalFirmwareRev69. entPhysicalFirmwareRev 2 Entity EntPhysicalFirmwareRev EntPhysicalSerialNum70. entPhysicalSerialNum Entity EntPhysicalSerialNum EntPhysicalMfgName72. entPhysicalModelName 1 Entity EntPhysicalModelName 71. entPhysicalMfgName Entity EntPhysicalMfgNameEntPhysicalModelName 73. entPhysicalAlias Entity EntPhysicalAlias 72. entPhysicalModelName 2 Entity EntPhysicalModelNameEntPhysicalAlias EntPhysicalAssetID 74. entPhysicalAssetID Entity EntPhysicalAssetIDEntPhysicalIsFRU 75. entPhysicalIsFRU 1 Entity75. entPhysicalIsFRU 2 Entity EntPhysicalIsFRU EntityLogical Group76. entLogicalEntry entLogicalTable Sup Object EntLogicalIndexEntLogicalTAddress EntLogicalIPDomainEntLogicalContextEngineID EntLogicalContextNameMpeEntPhysicalExtAdminStatus EntPhysicalChildIndex Entity EntPhysicalIndex SemanticEntityGeneral Group EntityNotifications GroupEntPhySensorValueUpdateRate MpeEntPhysicalExtOperStatusEntity Sensor MIB RFC 81. Entity Sensor MIB CommentsIfMauTable Supporte Object Type Access IfMauIfIndex ROIfMauIndex RO IfMauType ROIfMauDefaultType RW IfMauStatus ROIfMauAutoNegSupported RO IfMauTypeListBits ROPdnMgmtIpPortIndex NA 84. PDN-MGMT-IP-MIB Object Type SupportedPdnMgmtIpPortTable PdnMgmtIpConfigMode RW PdnMgmtBootIfIndex RWPdnMgmtBootVpi RW PdnMgmtBootVci RWPdnMgmtAtmInvArpTable PdnMgmtAtmIfIndex NAPdnMgmtAtmVpi NA PdnMgmtAtmVci NASnmpEngineBoots Supporting MIBs SNMP-MPD-MIB RFCSnmpEngineID SnmpEngineTimeSNMPv1 traps Default values SNMPv2 traps Default valuesSnmpTargetParmsTable SnmpUnavailableContexts and snmpUnknownContextsView-based Access Control Vacm User-based Security Model USM RFCSupporting MIBs StatisticsVacmAccessTable VacmContextTableVacmSecurityToGroupTable VacmViewTreeFamilyTableLink Fault Management 86. pdnLinkFaultMgmtApsSelection CommentsApsConfigMode ApsConfigRowStatusPdnLLSConfigGroupName PdnLLSConfigSelection88. pdnLinkFaultMgmtSwitchoverSelection Comments Link Load Sharing LLS PDN-LINK-LOAD-SHARING-MIB.mibPdnRedunCommand PdnRedunAlarmStatusPdnRedunNotificationEnable PdnRedunEntityStateDevConfigTestTimeout Timing and Clocking Paradyne mpeConfig MIB mpeConfig.mib90. mpeDevConfigClockSrcEntry Object Type Access Supported DevConfigTestDuration 92. pdntime.mib Object Type Access SupportedParadyne Time Mib pdntime.mib DevDateAndTime RWDevNTPEnable RW DevNTPOffsetFromUTCSysDevUserAccountUserPassword RC SysDevUserAccountAccessPartition RC93. pdndslam.mib Objects Supported Type SysDevUserAccountTableSecurityMgrSnmpAccess RW Paradyne Security MIB pdnSecurity.mib94. pdnSecurity.mib Object Type Supported DevSecurityMgrValidation RWSecurityMgrTelnetAccessRW SecurityMgrFtpAccess RWSecurityMgrTrapAccess RW SecurityMgrRowStatus RWMpeDevFileXferFileType3 MpeDevControlTable MpeDevFileXferConfigTable95. mpeControl.mib 2 Object Type Supported MpeDevFirmwareControlTable PdnSyslogStatus RW PdnSyslogIPAddr RWPdnSyslogLevel PdnSyslogPort RWPdnSyslogSeverityThreshold RW PdnSyslogRemoteDaemon RWPdnEntitySyslogTable NA PdnEntitySyslogNumber NATraps PdnDevConfigTrapsEnable RW pdnTrapMgr.mib PdnSyslogRateLimiting RWParadyne Health and Status MIB mpeHealthAndStatus.mib 97. Health and Status MIB Comments98. devLastTrapString 2 DevLastTrapString DSX Traps 98. devLastTrapString 3 DevLastTrapString Adsl Specific Traps98. devLastTrapString 4 DevLastTrapString IMA Traps Network Management Specification June Index IN-2 IN-3 IN-4
Related manuals
Manual 58 pages 27.69 Kb Manual 108 pages 33.36 Kb

8620, 8820 specifications

The Paradyne 8620 and Hotwire 8620 GranDSLAM are advanced DSLAM devices designed to provide high-speed broadband access over existing copper lines. This installation guide will outline the main features, technologies, and characteristics of these powerful units.

The Paradyne 8620 is engineered to support various DSL technologies, including ADSL, ADSL2+, and VDSL. This versatility allows operators to deploy services tailored to the needs of their customers, enabling data rates of up to 50 Mbps downstream, making it an ideal choice for meeting increasing bandwidth demands. The Hotwire 8620 GranDSLAM shares many similarities, focusing on providing enhanced service delivery for both residential and business users.

One of the key features of the GranDSLAM series is its modular architecture. Both models support up to 48 subscriber line interfaces in a single chassis, which provides significant scalability. Operators can seamlessly increase capacity by adding additional cards to accommodate growth. The devices are designed for easy deployment and management, equipped with an intuitive web-based interface that simplifies configuration and monitoring tasks.

Both units also feature advanced management capabilities, including support for SNMP and TR-069 protocols. This allows service providers to manage and provision devices remotely, significantly reducing operational costs and improving service reliability. The GranDSLAM models can also provide detailed diagnostic information, helping operators quickly identify and troubleshoot issues.

The Paradyne and Hotwire series ensure interoperability with various customer premises equipment, enabling service providers to offer bundled services such as voice, video, and data over the same connection. This capability is enhanced by the units’ ability to support VLANs and QoS features, ensuring that high-priority traffic receives the necessary bandwidth.

In addition to performance, the 8620 series is built with energy efficiency in mind. By utilizing power-saving features, these units help reduce overall operational costs while still providing reliable service.

Overall, the Paradyne 8620 and Hotwire 8620 GranDSLAM are robust solutions for service providers looking to deliver high-speed broadband services. Their modular design, advanced management capabilities, and support for multiple DSL technologies make them an excellent choice for today’s demanding telecommunications environment. With these advantages, operators can effectively meet customer needs while preparing for future growth and technology advancements.
Top Page Image Contents