Paradyne 9720, 9788 manual Communication Port Options 3, Inactivity Timeout

Page 101

4. Configuration Options

Table 4-25. Communication Port Options (3 of 4)

Inactivity Timeout

Possible Settings: Enable, Disable

Default Setting: Enable

Determines whether a user session is disconnected after a specified time of inactivity (no keyboard activity).

Display Conditions – This option appears only when Port Use is set to Terminal.

Enable – Disconnects user session after the specified time of inactivity (next option).

Disable – Does not timeout and disconnect user session.

Disconnect Time (Minutes)

Possible Settings: 1 – 60

Default Setting: 10

Sets the number of minutes of inactivity that can elapse before the session is ended.

Display Conditions – This option appears only when Port Use is set to Terminal.

1 – 60 – Sets the time from 1 to 60 minutes.

IP Address

Possible Settings: 001.000.000.000–126.255.255.255,

128.000.000.000–223.255.255.255, Clear

Default Setting: Clear (000.000.000.000)

Specifies a unique IP address for accessing the unit via the COM port. This option is only in effect when the COM port is configured as a network communication link

(Port Use option is set to Net Link).

Display Conditions – This option appears only when Port Use is set to Net Link.

001.000.000.000 – 223.255.255.255 – Shows the IP address for the COM port, which you can view or edit. The first octet of the address cannot be decimal 0 or 127, or greater than 223.

Clear – Clears the IP address for the COM port and fills the address with zeros. When the IP Address is all zeros, the COM port uses the Node IP Address if one has been configured.

Subnet Mask

Possible Settings: 000.000.000.000 – 255.255.255.255, Clear

Default Setting: 000.000.000.000

Specifies the subnet mask needed to access the unit. Only in effect when the COM port is configured as a network communication link (Port Use option is set to Net Link).

Display Conditions – This option appears only when Port Use is set to Net Link.

000.000.000.000 – 255.255.255.255 – Shows COM port subnet mask, which you can view or edit.

Clear – Clears the subnet mask for the COM port and fills the address with zeros. When the node subnet mask is all zeros, the IP protocol creates a default subnet mask based upon the IP address class: Class A: 255.000.000.000, Class B: 255.255.000.000, or Class C: 255.255.255.000.

9700-A2-GB20-20

December 2002

4-61

Page 100 Page 102
Image 101
Page 100 Page 102
Contents FrameSaver DSL Copyright 2002 Paradyne Corporation All rights reserved Contents Configuration Options Configuration ProceduresSecurity and Logins Configuring the FrameSaver DSL RouterDecember Access Levels Command Modes Changing Access LevelsViewing LMI Captured Packets from the User Interface TroubleshootingMenu Hierarchy Setting Up Network Health for FrameSaver DeviceSnmp MIBs, Traps, and Rmon Alarm Defaults Connectors, Cables, and Pin Assignments Router CLI Commands, Codes, and DesignationsRouter Command Line Summaries and Shortcuts Index Technical Specifications Equipment ListDocument Organization About This GuidePurpose and Intended Audience Technical Manuals → Technical Glossary Document Number Document Title Product-Related DocumentsNetScout Documentation Concord Communications DocumentationConvention Interpretation Conventions UsedX.x XxxxxxxxxxxxSystem Overview About FrameSaver DSL DevicesRouter-Specific Features FrameSaver DSL FeaturesCSU/DSU-Specific Features About FrameSaver DSL Devices Diagnostic Feature Set Model # Product PVCs Diagnostic Feature SetAdvanced SLM Feature Set Advanced SLM Feature Set Access Network Network Configuration ExamplesRemote Site Customer Premises HQ SiteCentral Office Customer Premises AccessOpenLane SLM System OpenLane FeaturesAbout FrameSaver DSL Devices December User and Command Line Interfaces Basic Operation Logging On If your login was ThenEnding a Session ProcedureSelect Main MenuScreen Format Description Screen Work AreasPress Navigating Menu-Driven User Interface ScreensKeyboard Keys For the screen Select Function Press Enter to Function KeysSelecting from a Menu Device Name MyDeviceName Switching Between Screen AreasSelecting a Field for Input CLI Keyboard Keys Navigating the Router’s CLI9700-A2-GB20-20 Configuration Procedures Configuration Edit/Display Menu Basic Configuration From the User InterfaceConfiguration Option Area Description Configuration Option AreasMain Menu Configuration Accessing and Displaying Configuration OptionsConfiguration PVC Connections Changing Configuration OptionsSaving Configuration Options Configuration Procedures Configuration Options Configuration Options Easy Install Screen Using the Easy Install FeatureMain Menu Easy Install Easy Install Configuration Options 1 Network 1 DSL Line Rate Mode Easy Install Configuration Options 2Create a Dedicated Network Management Link Ethernet Management Options ScreenNetwork 1 DSL Line Rate Easy Install Configuration Options 3384 784Port-1 Port Type 9788 CSU/DSU Easy Install Configuration Options 4Network 1 Channel Changing the Operating Mode Entering System Information and Setting the System ClockMain Menu Control Change Operating Mode Main Menu Control System InformationConfiguration Option Tables Main Menu Configuration System Frame Relay and LMI Configuring the Overall SystemConfiguring Frame Relay and LMI for the CSU/DSU LMI Clearing Event N3 LMI Error Event N2CSU/DSU Frame Relay and LMI Options 2 LMI Status Enquiry N1 LMI Heartbeat T1 Possible Settings 5, 10, 15, 20, 25CSU/DSU Frame Relay and LMI Options 3 Field Setting After RfcCodePoints Selected Configuring Class of Service DefinitionsMain Menu Configuration System Class of Service Definitions Class of Svc Name Class of Service DefinitionsMeasure Latency & Availability Code Points AssignedCode Point Definitions Code Point DefinitionsCode Pnt NameMain Menu Configuration System Service Level Verification Configuring Service Level Verification OptionsService Level Verification Options 1 SLV Sample Interval secsSLV Type Available Settings Standard, COS 1-COS Service Level Verification Options 2Dlci Down on SLV Timeout SLV Delivery RatioService Level Verification Options 3 Test Duration min Configuring General System OptionsMain Menu Configuration System General Configuring the Network Physical Interface Configuring Network InterfacesMain Menu Configuration Network Physical Operating Rate Possible Settings AutoRate, 64, 128DSL Line Rate Kbps Line Rate Mode Possible Settings Hunt, AutoRate, FixedNetwork Physical Interface Options 776, 784, 1544 Line Rate Mode2056 RegionConfiguring Dlci Records for the Network Interface Configuring Frame Relay for the Network InterfaceMain Menu Configuration Network Frame Relay Main Menu Configuration Network Dlci RecordsMain Menu Configuration Network Circuit Records Configuring Circuit Records for the Network Interface 978311. Circuit Records Options 1 Dlci NumberCIR bps 11. Circuit Records Options 29783 0 9788 0 Committed Burst Size Bc BitsExcess Burst Size Be Bits 11. Circuit Records Options 39783 9788 Outbound Management PriorityMain Menu Configuration Network ATM Configuring ATM for the Network Interface 9783Cell Delineation Error Event Threshold Cell Payload ScramblingConfiguring the CSU/DSU’s Data Port Physical Interface Configuring the User Data or Virtual Router PortMain Menu Configuration Data Ports Physical 13. CSU/DSU Data Port Physical Interface Options 1Transmit Clock Source 13. CSU/DSU Data Port Physical Interface Options 2Monitor RTS Control Monitor DTRMain Menu Configuration Data Ports Frame Relay Configuring Frame Relay on the CSU/DSU’s Data Port14. CSU/DSU Frame Relay Options 1 LMI14. CSU/DSU Frame Relay Options 2 Main Menu Configuration Network Dlci Records Data Ports Configuring Dlci RecordsFrame relay interface. Dlci Reserved. Entry of an9720 0 9783 0 9788 0 15. Dlci Records 2Dlci Priority 15. Dlci Records 39720 16. PVC Connections 1 Configuring PVC ConnectionsMain Menu Configuration PVC Connections Destination Link 16. PVC Connections 2Destination Dlci Destination Edlci17. IP Path List Configuring the IP Path ListMain Menu Configuration IP Path List Static Management Link Setting Up Management and CommunicationConfiguring Node IP Information 18. Node IP Options 1 Management MTU Size TS Access Management Link18. Node IP Options 2 Components associated with the deleted PVC? Configuring Management PVCsPayload Managed 19. Management PVC Options 1Primary Dlci 19. Management PVC Options 2Set DE Primary Edlci 19. Management PVC Options 3Primary VPI,VCI Number VPI 0 VCI 32Encapsulation 19. Management PVC Options 4Name 1 Access Configuring General Snmp Management20. General Snmp Management Options 1 Snmp Management20. General Snmp Management Options 2 Name 2 AccessTelnet Login Required Configuring Telnet and/or FTP Sessions21. Telnet and FTP Session Options 1 Telnet Session21. Telnet and FTP Session Options 2 Inactivity TimeoutDisconnect Time Minutes FTP Session21. Telnet and FTP Session Options 3 FTP Login RequiredFTP Max Transfer Rate Kbps 9720 1 9783 1 9788 122. Snmp NMS Security Options 1 Configuring Snmp NMS SecurityNMS IP Validation Number of Managers22. Snmp NMS Security Options 2 Access Type23. Snmp Traps Options 1 Configuring Snmp TrapsSnmp Traps Number of Trap ManagersEnterprise Specific Traps 23. Snmp Traps Options 2Possible Settings Network, Ports, All, None Link Traps Possible Settings Disable, Up, Down, Both23. Snmp Traps Options 3 Link Traps InterfacesRmon Traps 23. Snmp Traps Options 4Latency Traps IP SLV Availability TrapsStatus Configuring Ethernet Management24. Ethernet→Management→Options 1 Proxy ARP 24. Ethernet Management Options 225. Communication→ Port→Options 1 Configuring the Communication PortPort Use Character Length25. Communication Port Options 2 Login RequiredStop Bits Ignore Control Leads25. Communication Port Options 3 RIP 25. Communication Port Options 4Main Menu Configuration Management and Communication Configuring the COM Port to Support an External ModemExternal Modem Com Port→ 26. External Modem COM Port OptionsConfiguration Options December NAT and Napt Configuration Example Configuring the FrameSaver DSL RouterEthernet FrameSaver DSL Router OverviewDSL Network Interface Proxy ARP Address Resolution ProtocolIP Routing Interface Configuration Applications Supported by NAT Network Address TranslationIP Options Processing NAT Mapping Public IP Addresses Private IP Addresses NAT Configuration ExampleSave exit Napt Mapping Public IP Address Private IP Addresses Napt Configuration ExampleNetwork Address Port Translation Int ethernet 0 ip nat inside int serial 0.x ip nat outside Access-list 1 permit 10.1.3.0Ip nat inside source list 1 interface se 0.x overload Ip nat inside source static 10.1.1.1 NAT and Napt Configuration ExampleDynamic Host Configuration Protocol Server NAT Dhcp Server with NAT Configuration ExamplePublic IP Addresses for NAT Private IP Addresses Dhcp Relay Agent Dhcp Server at Remote Site Configuration ExampleIp dhcp server Ip route 155.1.3.254 serial Dhcp Relay Configuration ExampleDhcp LAN DSLIP Router Filtering Bridge Filtering Router SecurityLand Bug Prevention IP FilteringSmurf Attack Prevention NAT DSLProvisioning the Router Interface Diagnostics ATM Ping D-CVerifying the End-to-End Management Path Configuring the Router Using Terminal Emulation Security and Logins FTP Snmp Limiting AccessSet the configuration option Controlling Asynchronous Terminal AccessExternal Modem Com Port Controlling External COM Port Device AccessControlling Telnet and FTP Access See Creating a Login for the User Interface on Limiting Telnet AccessFTP Limiting FTP AccessLimiting Telnet or FTP Access Over the TS Management Link Disabling Snmp Access Controlling Snmp AccessAssigning Snmp Community Names and Access Levels See Configuring→General Snmp →Management in , Configuration Limiting Snmp Access Through IP AddressesLargo Controlling Router CLI AccessAccess Levels Command Modes Page Main Menu Control Administer Logins Creating a Login for the User InterfaceSecurity in , Configuration Options Field EnterExample Modifying a LoginDeleting a Login Operation and Maintenance View this field To find Displaying Identity System InformationMain Menu Status Identity Viewing LEDs and Control Leads Main Menu Status Display LEDs and Control Leads Display LEDs & Control Leads Screen for a 9783 Router LED DescriptionsLED Descriptions 1 Label Indication Color What It MeansLED Descriptions 2 Control Lead DescriptionsNetwork LEDs Port LED CSU/DSUControl Leads Label Indication What It Means Device Messages 1 What It Indicates What To Do Device MessagesSeen at an FTP TerminalSoftware. See Activating Software Device Messages 2 What It Indicates What To DoDevice Messages 3 What It Indicates What To Do See Upgrading System Device Messages 4 What It Indicates What To DoCOM Port usage field Device Messages 5 What It Indicates What To DoMaximumDHCPClients Router CLI MessagesCLI Messages 1 What It Indicates Start-ip-address or end-ip-address CLI Messages 2 What It IndicatesEither pool or interface, and overload are CLI Messages 3 What It IndicatesCLI Messages 4 What It Indicates CLI Messages 5 What It Indicates Status Menu Status InformationSystem and Test Status Messages Last ResetSelf-Test Results Messages Main Menu Status System and Test StatusHealth and Status Messages 1 What It Indicates Health and Status MessagesAtmlink Health and Status Messages 2 What It IndicatesPathIP Address Down InterfaceDLCInnnnTest Status Messages IP Path Connection StatusTest Status Messages What It Indicates Main Menu Status IP Path Connection StatusIP Path Connection Status IP Path Connection Status Screen ExampleFR Link Net1-FR1, Port-1 Frame relay link This is the IP addressPVC Connection Status Screen Example PVC Connection StatusPVC Connection Status Screen 1 Field Display What It IndicatesEdlci PVC Connection Status Screen 2Network Interface Status Screen Example Network Interface StatusMain Menu Status Network Interface Status IP Routing Table Screen Example IP Routing Table Management TrafficTTL 11. IP Routing Table Values Field What It IndicatesPerformance Statistics Menu Performance StatisticsMain Menu Status Performance Statistics 13, SLV Performance Statistics for IP Enabled Dlci Service Level Verification Performance StatisticsInbound Dropped Dlci connection COS ID Service Definitions in , Configuration OptionsMain Menu Status Performance Statistics Dlci Dlci Performance Statistics14. Dlci Performance Statistics 1 Field What It Indicates CIR&EIR14. Dlci Performance Statistics 2 Field What It Indicates Additional Performance Statistics for IP Enabled DlciFrame Relay Performance Statistics Frame Relay Errors16. Frame Relay Performance Statistics 1 What It Indicates Frame Relay LinkFrame Relay LMI CSU/DSUs only Frame Relay Hdlc Errors16. Frame Relay Performance Statistics 2 What It Indicates ATM Performance Statistics 9783 OAM Operations, Administration, and Maintenance17. ATM Performance Statistics What It Indicates AAL5 ATM Adaption LayerMain Menu Status Performance Statistics VCC VCC Performance Statistics 978318. VCC Performance Statistics 1 What It Indicates VCC Virtual Channel Connection18. VCC Performance Statistics 2 What It Indicates Shdsl Line Performance StatisticsMain Menu Status Performance Statistics XDSL Line 19. Shdsl Line Performance Statistics What It Indicates20. Ethernet Performance Statistics What It Indicates Ethernet Performance StatisticsMain Menu Status Performance Statistics Ethernet Function key Main Menu Clearing Performance StatisticsFrame Relay → →EthernetTrap Event Log Screen Example Trap Event LogFTP File Transfers Initiating an FTP Session Command DefinitionIf the message displayed is Then Upgrading System SoftwareMain Menu Control Select Software Release Determining Whether a Download Is CompletedActivating Software Main Menu Control LMI Packet Capture Utility Transferring Collected DataIf retrieving Then Troubleshooting Indicators See Problem IndicatorsDevice Messages in , Operation and Maintenance Main Menu Status Display LEDs and Control LEDsResetting the Unit By Cycling the Power Resetting the Unit and Restoring CommunicationResetting the Unit from the Control Menu If selecting Following occurs Restoring Communication with an Improperly Configured UnitMain Menu Control LMI Packet Capture Utility Troubleshooting Management Link FeatureLMI Packet Capture Utility Feature LMI Trace Log Example Viewing LMI Captured Packets from the User InterfaceTelnet Example TelnetControl Telnet Alarm Conditions 1 What It Indicates What To Do AlarmsCSU/DSU only minor Alarm Alarm Conditions 2 What It Indicates What To DoOnly minor alarm IPAddressPathIP Address Alarm Conditions 3 What It Indicates What To DoDown minor alarm Viewing the Trap Event Log Troubleshooting TablesDevice Problems Symptom Possible Cause Solutions Device ProblemsATM Problems Symptom Possible Cause Solutions ATM ProblemsFrame Relay PVC Problems Symptom Possible Cause Solutions Frame Relay PVC ProblemsRouter Test Menu Example Tests AvailableCSU/DSU Test Menu Example Test Timeout Feature Aborting All Tests Starting and Stopping a TestPVC Tests Screen Example PVC TestsSend Pattern PVC LoopbackMain Menu Test Network PVC Tests Main Menu Test Data Port PVC TestsTo run a connectivity test on a link When 5 frames out of 25 are missing or out of sequenceMonitor Pattern Network ATM Loopback Tests Screen Example Network ATM LoopbackFor Main Menu Test Data Port Physical Tests Data Port Physical TestsDTE Loopback On page 8-29 to ping Snmp trap managers Ping Screen Example IP Ping TestSource IP Address Ping Options 1Target IP Address Response Timeout Inter-Ping DelayPing Options 2 Packet SizePing Responses Field Possible Values Description Main Menu Test IP Ping IP Ping Test ProcedureCentral →site NMS, then select Start Main Menu Test Lamp Test Lamp TestSetting Up OpenLane for FrameSaver Device OpenLane Support of FrameSaver Devices Setting Up the OpenLane SLM SystemSetting Up FrameSaver Support To Find Your License Key Number Ordering Advanced SLM Feature Set ActivationsActivation Certificate Administering and Managing Advanced SLM Activations Checking Activation Certificate Status Entering an Activation CertificateScheduling Activations Checking the Status of Scheduled Activations Canceling Scheduled ActivationsAccessing and Printing the Certificate Summary Report Setting Up OpenLane for FrameSaver Device December Setting Up Network Health for FrameSaver Device Installation and Setup of Network Health Discovering FrameSaver Elements Configuring the Discovered Elements Grouping Elements for Reports About At-a-Glance Reports About Service Level ReportsGenerating Reports for a Group Printed Reports Reports Applicable to FrameSaver DevicesAbout Trend Reports 10-8 FrameSaver SLV Plus At-a-Glance Report 10-910-10 Menus Menu HierarchyFrameSaver DSL CSU/DSUs Menu Structure Change Operating Mode Administer LoginsReset Device SystemVCC FrameSaver DSL Routers Menu StructureVirtual Router Ports Menu Hierarchy December Snmp MIBs, Traps, and Rmon Alarm Defaults Support Online Technical Support MIB SupportDownloading MIBs and Snmp Traps FrameSaver Unit’s sysObjectID system System Group mib-2FrameSaver Unit’s sysDescr system Paradyne Indexes to the Interface Table ifTable Interfaces Group mib-2Physical Layer Frame Relay Logical LayerRmon Logical Layer NetScout Probe Indexes to the Interface Table ifTableInterface number Dlci number ALLExamples Standards Compliance for Snmp TrapsTrap warmStart Trap authenticationFailureTable B-3. warmStart Trap What It Indicates Possible Cause Variable-BindingTable B-5. linkUp and linkDown Traps What It Indicates Trap linkUp and linkDownPhysical Sublayer Strings‘$ifString $alarmString down.’ ATM Logical Link Sublayer MIBXxx.xxx.xxx.xxx , COS nn Trap enterprise-Specific‘Path xxx.xxx.xxx.xxx Up Nnnn ’Trap RMON-Specific Event Defaults Rmon Alarm and Event DefaultsEventIndex EventDescription EventType Rising Event OperationFrame Relay Link Alarm Defaults Network Physical Interface Alarm DefaultsOID OID Dlci Alarm DefaultsCIR 6.1.2.1.2.10.32.2.1 OID Cross-References6.1.2.1.2.2.1 Dlci CIR 6.1.4.1.1795.2.24.2.6.9.4.1.16.1.4.1.1795.2.24.2.6.9.4 Dlci EIR6.1.4.1.1795.2.24.2.6.9.4.4.2 6.1.4.1.1795.2.24.2.6.9.4.5.2.16.1.4.1.1795.2.24.2.6.9.4.10.3.1 6.1.4.1.1795.2.24.2.6.9.4.7.16.1.2.1.10.32.2.1 6.1.4.1.1795.2.24.2.6.9.4 CLI Commands Router CLI Commands, Codes, DesignationsConvention Translation Interfaces, and Basic Operation, for additional informationRouter CLI Commands, Codes, and Designations Access Control Commands Pager CommandTable C-1. Pager Command Table C-2. Access Control CommandsTable C-3. Configuration Commands Configuration CommandsConfigure terminal factory SaveCommand Mode config, config-if, config-subif Interface CommandsTable C-4. Interface Commands 1 Encapsulation encapsulation-type encapsulation-protocol Table C-4. Interface Commands 2No frame-relay interface-dlci dlci-num Table C-4. Interface Commands 3No ip unnumbered null Table C-5. IP Routing Commands IP Routing CommandsNo ip routing No ip multicast-routingTable C-6. Bridge Commands 1 Bridge CommandsNo bridge-group bridge-group Table C-6. Bridge Commands 2Command Mode config-if, config-subif Table C-7. ARP Commands ARP CommandsArp timeout time No arp timeout time Clear arp-cacheNo ip nat inside outside NAT CommandsTable C-8. NAT Commands 1 Ip nat pool pool-name start-ip-addr end-ip-addr Table C-8. NAT Commands 2Netmask netmask prefix-length / prefix-length No ip nat pool pool-namestart-ip-addr end-ip-addrFrom previous Table C-8. NAT Commands 3Clear ip nat translation Table C-9. Dhcp Server Commands 1 Dhcp Server CommandsNo service dhcp No ip dhcp pool pool-nameDefault-router ip-address No default-router ip-address Table C-9. Dhcp Server Commands 2Domain-name domain-name No domain-name domain-name Dns-server ip-address No dns-server ip-addressNetwork network-num Table C-9. Dhcp Server Commands 3No ip dhcp-server ip-address Dhcp Relay Agent CommandsTable C-10. Dhcp Relay Agent Commands Table C-11. Filter Commands 1 Filter access-list CommandsAccess-list access-list-numpermit deny No access-list access-list-numpermit denyFor Extended IP Access Lists Table C-11. Filter Commands 2For Protocol Type Access Lists Table C-11. Filter Commands 3No ip access-group access-list-1-199numin out Table C-11. Filter Commands 4Table C-12. Diagnostic Commands 1 Diagnostic CommandsTraceroute protocol dest-ipsource source-ip length bytes Table C-12. Diagnostic Commands 2Table C-13. Show Commands 1 Show CommandsShow configuration Show arpShow configuration saved unsaved Table C-13. Show Commands 2Show frame-relay map Show interface intf-type intf-num .sub-intf-numShow ip dhcp binding ip-address Table C-13. Show Commands 3Show ip nat translations Show ip route ip-addressShow spanning-tree Table C-13. Show Commands 4Show ip traffic Table C-14. Ethernet Type Codes Hex 1 Description Ethernet Type CodesTable C-14. Ethernet Type Codes Hex 2 Description All 3 n = Destination unreachable Protocol and Port DesignationsIcmp Designations All 5 n = All redirects TCP Port Designations UDP Port Designations CLI Summaries Router Command Line Summaries ShortcutsIntf-type intf-num .sub-intf-num Show Command SummaryTable D-1. Show Commands Function Table D-2. Access Control and System Level Commands Function Access Control and System Level Command SummaryTable D-3. CLI Commands 1 CLI Command SummaryClear counters intf-type intf-num .sub-intf-num Dns-serverip-addressEncapsulation encapsulation-type encapsulation-protocol Table D-3. CLI Commands 2CLI Command Default Settings Connectors, Cables, and Pin Assignments Figure E-1. Model 9720 CSU/DSU Rear Panel Rear PanelsFigure E-4. Model 9783 Router Rear Panel RJ48C Table E-1. DSL Network Interface Connector Pin # SignalDSL Network Interface and Cable Model 9720 and 9788 COM Port Connector Model 9783 COM Port ConnectorEthernet Port Connector Table E-5. Model 9720 and 9783 CSU/DSU Data Port Connector Model 9720 and 9783 CSU/DSU Data Port ConnectorSignal Number Direction Pin Standard V.35 Straight-through CableSignal Mnemonic Number Direction Pin Model 9788 CSU/DSU Data Port ConnectorTable E-6. Model 9788 CSU/DSU Data Port Connector Circuit EIA-530-A-to-V.35 Adapter Signal Plug SocketEIA-530-A-to-X.21 Adapter Enter AT Command To configure the modem to Configuring an External ModemTXD RXD RTS DSR DB25-to-DB25 Crossover CableCD Rlsd RXC DTR Xtxc RXC DTR XtxcPin DB9-to-DB25 Crossover CablePin Connectors, Cables, and Pin Assignments December Technical Specifications COM Port 9720 COM PortDSL Network Interface Ethernet PortEquipment Equipment ListDescription Model Number FrameSaver DSL 9720 CSU/DSUsFrameSaver DSL 9788 CSU/DSUs FrameSaver DSL 9783 DSU/CSUsFrameSaver DSL 9788 Routers FrameSaver SLV UpgradeFrameSaver DSL 9783 Routers NMS Products Optional Housing Mounting Kit FeaturesFor connection to an external device with a DB9 connector Description Part Number Feature NumberCables For use in the U.SEquipment List December Numerics IndexIN-2 COS IN-3IN-4 IN-5 IP SLV IdslIN-7 IN-8 IN-9 PVC Rmon IN-10SLV ShdslSLM IN-12 IN-13 IN-14
Related manuals
Manual 166 pages 36.17 Kb

9720, 9788 specifications

The Paradyne 9820-8M, 9788, 9128 standalone, 9128 carrier-mount, and 9820-2M are critical components in telecommunications networks, designed to enhance data transmission and improve connectivity. Each model offers unique features and capabilities that cater to various requirements in both enterprise and service provider environments.

The Paradyne 9820-8M is a multi-service access platform that provides high-speed connectivity for voice, video, and data transmission. It supports multiple protocols, enabling seamless integration into existing infrastructures. Key features include a modular design that allows for scalability and easy upgrades, ensuring that organizations can adapt to evolving demands. Its advanced error correction and QoS (Quality of Service) features ensure reliable performance, even in challenging network conditions.

The Paradyne 9788 serves as a versatile platform for both digital and analog communications. It excels in the delivery of broadband services, supporting T1/E1 lines and providing robust mechanisms for data transmission. This model emphasizes redundancy and resilience, with built-in protection switching capabilities that maintain service continuity during faults or maintenance activities. Its compact design makes it an ideal solution for environments with space constraints.

The 9128 standalone model is aimed at customers requiring an easy-to-deploy solution for point-to-point connections. This model offers critical features such as an intuitive user interface, comprehensive diagnostics, and monitoring capabilities that facilitate system management. It also supports diverse network topologies, making it suitable for various deployment scenarios.

In contrast, the 9128 carrier-mount version is engineered for organizations needing to manage multiple connections within a central office or remote site. This model is specifically designed to be mounted in standard telecom racks, optimizing space utilization while maintaining high performance. Its robust hardware allows for excellent thermal management and environmental resilience.

Lastly, the Paradyne 9820-2M combines versatility with high-performance capabilities, making it a reliable choice for service providers. It features dual-channel support, enabling simultaneous transmission and providing a cost-effective solution for high-capacity data needs. With enhanced security features, including encryption capabilities, the 9820-2M ensures that sensitive information transmitted across networks is protected against unauthorized access.

Collectively, these Paradyne models exemplify advanced telecommunications technology, offering scalability, resilience, and high performance. Their diverse features cater to the unique demands of various users, from enterprise networks to service providers, facilitating the continual evolution of communication technologies.
Top Page Image Contents