Patton electronic 1080A-64 Two-Wire Cable Connection Via RJ-45, RJ-45 Signal, Signal PIN# Color

Page 8

4.1.1Two-Wire Cable Connection Via RJ-45

A. The RJ-45 jack on a Model 1080A Series Short Range Modem is prewired for a standard TELCO wiring environment. To be sure you have the right wiring, use the table below as a guide.

RJ-45 SIGNAL

1-------------NC

2-------------GND

3-------------RCV

4-------------XMT

5-------------XMT

6-------------RCV

7-------------GND

8-------------NC

Connection to ground is optional

B.Proper wiring of pairs between the two modems is as follows:

SIGNAL

PIN#

COLOR*

COLOR

PIN#

SIGNAL

XMT

4

Green ------------

Green

4

XMT

XMT

5

Red ---------------

Red

5

XMT

*Standard color codes—yours may be different

C. AT&T standard modular color codes:

1 - Blue

2 - Orange

3 - Black

4 - Red

5 - Green

6 - Yellow

7 - Brown

8 - Slate

4.1.2 Two-Wire Cable Connection Via Terminal Blocks

If you are not going to use the modular jacks, follow the instructions below.

A. Locate the terminal block on the back of the unit. It should look like the following diagram:

RX+ RX- GND TX- TX+

NOTE: * The “+” and “-” indicators are for reference only. The Model 1080A Series is not sensitive to polarity.

B.Connect one wire of the pair to a Transmit lug (TX+ or TX-) on both the local and remote Model 1080A or 1080A-64.

C.Connect the other wire of the pair to the other Transmit lug on both the local and remote Model 1080A or 1080A/64.

D.If there is a shield around the telephone cable, it may be connected to GND on the terminal block. We recommend connecting the shield at the computer end only to avoid ground loops. A ground wire is not necessary for proper operation of these units.

E.When you finish connecting the telephone line to units at both ends, it should look like the following diagram:

XMT

 

XMT

}One Pair

XMT

 

XMT

GND

To Shield (Optional)

GND

 

4.2 FOUR-WIRE INSTALLATION

When communicating over a two twisted pair circuit, the Model Series can operate full or half duplex, point-to-point or multipoint. In two pair point-to-point applications, you will need a pair of Model 1080As or 1080A-64s for each circuit—one at each end of the single pair wire. In two pair multipoint applications you will need three or more Model 1080A Series units.. These can be connected using a star topology, although a daisy chain topology is usually used.

13

14

Image 8 Patton electronic 1080A-64 Two-Wire Cable Connection Via RJ-45, RJ-45 Signal, Signal PIN# Color, FOUR-WIRE Installation
Contents User Manual Service Radio and TV InterferenceCE Notice Tel 301Description FeaturesConfiguration Switches Configuration Switch SET S1 Model 1080A Data Rate SettingsData Rate Settings Model 1080A-64 Model 1080A S1 Summary TableConfiguration Switch SET S2 S2 Summary TableConfiguration Switch SET S3 S3 Summary TableS3-1, S3-2 Selection Table for Model 1080A S3-1, S3-2 Selection Table for Model 1080A-64TWO-WIRE Installation Switch S3-6 RS-232 Initiation of Remote Loopback TestSwitches S3-7 and S3-8 Anti-stream Control Two-Wire Cable Connection Via RJ-45 RJ-45 SignalSignal PIN# Color Two-Wire Cable Connection Via Terminal BlocksFour-Wire Cable Connection Via RJ-45 Four-Wire Cable Connection Via Terminal BlocksFOUR-WIRE, Multipoint Installation Multipoint Twisted Pair ConnectionHost First Slave Second Slave RS-232 ConnectionLED Status Monitors V.54 Test Modes ANTI-STREAMING Error IndicatorPOWER-UP POWER-DOWN Appendix a Patton Model 1080A Series SpecificationsPatton Model # Description Appendix C Patton Model 1080A Series Cable RecommendationsDirection Standard RS-232C/V.24 DCE Setting

1080A, 1080A-64 specifications

The Patton Electronics 1080A-64 and 1080A are versatile communication devices designed to streamline data transmission and enhance connectivity in various environments. As part of Patton's extensive range of telecommunications solutions, these models reflect the latest technological advancements in serial-to-IP conversion, ensuring reliable and efficient communication across diverse networks.

One of the standout features of the Patton 1080A-64 is its ability to support multiple serial ports, allowing seamless integration with a wide range of serial devices. This multi-port capability is particularly beneficial for businesses that operate various legacy systems, enabling them to bridge the gap between traditional serial protocols and modern IP-based networks. The 1080A is similarly equipped, ensuring that users can connect their existing infrastructure without extensive modifications.

Both models utilize advanced data encapsulation techniques, including the capability to handle standard protocols such as TCP, UDP, and RTP. This versatility ensures that users can implement the devices in various applications, including point-to-point and point-to-multipoint setups. Additionally, the incorporation of efficient data compression algorithms helps to optimize bandwidth usage, making these devices ideal for environments with limited data capacity.

Another significant characteristic of the Patton 1080A-64 and 1080A is their impressive security features. The devices are equipped with robust encryption options to protect data during transmission, ensuring that sensitive information remains secure against potential threats. This focus on security is particularly important for industries that handle confidential data, such as finance, healthcare, and government sectors.

The user-friendly interface of both models further enhances their appeal. With intuitive web-based management tools, administrators can easily configure settings, monitor performance, and troubleshoot issues in real time. This ease of use reduces downtime and allows businesses to maintain operational efficiency.

In terms of physical design, the Patton 1080A-64 and 1080A are built for durability and reliability. Their compact form factor and industrial-grade components make them suitable for deployment in various environments, from office settings to harsh industrial conditions.

Overall, the Patton Electronics 1080A-64 and 1080A stand out as reliable solutions for modern communication needs, combining multi-port support, advanced encapsulation technologies, strong security features, and user-friendly management capabilities. These models enable organizations to modernize their data transmission processes while maintaining compatibility with existing serial devices, making them valuable assets in today’s interconnected world.