Patton electronic 1080A-64 user manual LED Status Monitors

Page 11

5.0 OPERATION

Once you have configured each Model 1080A Series unit properly and connected the twisted pair and RS-232 cables (see Section 4.0), you are ready to operate the units. This section describes reading the LED status monitors, powering-up and using the built-in V.52 and V.54 test modes.

5.1 LED STATUS MONITORS

The Model 1080A Series features six front panel status LEDs that indicate the condition of the modem and communication link. Figure 5 shows the front panel location of each LED. Following Figure 5 is a description of each LED's function.

 

 

 

Model 1080 Universal Short Range Modem

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V.54 Test

TD

RD RTS CD

 

 

Modes

 

 

 

 

 

 

 

 

 

 

 

 

Error Test

 

 

 

 

 

511

Remote

511E

Normal

Local

Figure 5. Front view of Model 1080A Series

5.1.1 The “TD” and “RD” Indicators

The “TD” and “RD” indicators blink red and green with data activity. Red indicates a low RS-232 logic level, green indicates a high RS-232 logic level. Note: RS-232 devices idle in a low state, so the LED will glow red if the connections are correct and the RS-232 device is in an idle state.

5.1.2 The “RTS” and “CD” Indicators

The “RTS” and “CD” indicators are bi-color and will glow red for a “low” signal or green for a “high” signal. RTS lights for an incoming signal on RS-232 pin 4. CD lights for an incoming signal on the line side, and the resulting output signal on RS-232 pin 8.

5.1.3 The “Test” Indicator

The green “Test” LED indicates that V.52 or V.54 tests are running.

19

5.1.4 The “Error” Indicators

The “Error” indicator LED has three functions:

A.When the 1080A Series unit is in test mode (green “Test” LED is lit), the error LED glows red when bit errors occur.

B.When not in test mode (green “Test” LED is off), the error LED is used to indicate an RTS streaming condition. (See Section 5.2) for information on the anti-streaming circuitry.

C.The “Error” LED is also used to detect line quality, such:

1.The improper use of flat (non-twisted pair) cable to connect the modems.

2.One or more broken wire in the 4 wire twisted pair cable.

3.The use of low quality twisted pair cable to connect the modems.

4.Broken or corroded connector.

NOTE: In detecting line quality the “Error” LED indicator is designed for 4 wire twisted pair cable only, and may not function properly with two wire cable.

5.1.4.1 Setting Up The “Error” LED To Test Cable Quality

If there is any question as to the quality of your line we recommend the following test:

1.Disconnect both local and remote modems from their RS-232 interface. Make sure “TD”, “RD” and “RTS” LEDs are lit red.

2.Set input impedance of both modems to 200Ω . (S3-1 “On”, S3-2 “Off”).NOTE: When testing Model 1080A-64, use 22AWG, 24AWG, or 26AWG cable only,

3.For Model 1080A, set data rate on both modems for 9.6kbps For Model 1080A-64, set data rate on both modems at 16 kbps.

4.On local modem set “Carrier Constantly On”. (S1-8 “Off”)

5.Set remote modem to RTS control (S1-8, “On”).

6.Place both front panel toggle switches to neutral position. (Test Led will not light)

7.Connect both modems to the 4 wire twisted pair cable.

20

Page 10 Page 12
Image 11
Page 10 Page 12
Contents User Manual Tel 301 ServiceRadio and TV Interference CE NoticeDescription FeaturesConfiguration Switches Model 1080A S1 Summary Table Configuration Switch SET S1Model 1080A Data Rate Settings Data Rate Settings Model 1080A-64S2 Summary Table Configuration Switch SET S2S3-1, S3-2 Selection Table for Model 1080A-64 Configuration Switch SET S3S3 Summary Table S3-1, S3-2 Selection Table for Model 1080ATWO-WIRE Installation Switch S3-6 RS-232 Initiation of Remote Loopback TestSwitches S3-7 and S3-8 Anti-stream Control Two-Wire Cable Connection Via Terminal Blocks Two-Wire Cable Connection Via RJ-45RJ-45 Signal Signal PIN# ColorFour-Wire Cable Connection Via Terminal Blocks Four-Wire Cable Connection Via RJ-45RS-232 Connection FOUR-WIRE, Multipoint InstallationMultipoint Twisted Pair Connection Host First Slave Second SlaveLED Status Monitors V.54 Test Modes ANTI-STREAMING Error IndicatorPOWER-UP Appendix a Patton Model 1080A Series Specifications POWER-DOWNAppendix C Patton Model 1080A Series Cable Recommendations Patton Model # DescriptionDirection Standard RS-232C/V.24 DCE Setting

1080A, 1080A-64 specifications

The Patton Electronics 1080A-64 and 1080A are versatile communication devices designed to streamline data transmission and enhance connectivity in various environments. As part of Patton's extensive range of telecommunications solutions, these models reflect the latest technological advancements in serial-to-IP conversion, ensuring reliable and efficient communication across diverse networks.

One of the standout features of the Patton 1080A-64 is its ability to support multiple serial ports, allowing seamless integration with a wide range of serial devices. This multi-port capability is particularly beneficial for businesses that operate various legacy systems, enabling them to bridge the gap between traditional serial protocols and modern IP-based networks. The 1080A is similarly equipped, ensuring that users can connect their existing infrastructure without extensive modifications.

Both models utilize advanced data encapsulation techniques, including the capability to handle standard protocols such as TCP, UDP, and RTP. This versatility ensures that users can implement the devices in various applications, including point-to-point and point-to-multipoint setups. Additionally, the incorporation of efficient data compression algorithms helps to optimize bandwidth usage, making these devices ideal for environments with limited data capacity.

Another significant characteristic of the Patton 1080A-64 and 1080A is their impressive security features. The devices are equipped with robust encryption options to protect data during transmission, ensuring that sensitive information remains secure against potential threats. This focus on security is particularly important for industries that handle confidential data, such as finance, healthcare, and government sectors.

The user-friendly interface of both models further enhances their appeal. With intuitive web-based management tools, administrators can easily configure settings, monitor performance, and troubleshoot issues in real time. This ease of use reduces downtime and allows businesses to maintain operational efficiency.

In terms of physical design, the Patton 1080A-64 and 1080A are built for durability and reliability. Their compact form factor and industrial-grade components make them suitable for deployment in various environments, from office settings to harsh industrial conditions.

Overall, the Patton Electronics 1080A-64 and 1080A stand out as reliable solutions for modern communication needs, combining multi-port support, advanced encapsulation technologies, strong security features, and user-friendly management capabilities. These models enable organizations to modernize their data transmission processes while maintaining compatibility with existing serial devices, making them valuable assets in today’s interconnected world.
Top Page Image Contents