Patton electronic 2173 Connecting Power, Configuration, Configuring the Hardware DIP Switches

Page 12

 

1 TX+/RX+

1

2 TX-/RX-

2

3 RX+/TX+

3

4

(no connection)

4

 

 

5

5

(no connection)

6

6

RX-/TX-

7

7 (no connection)

8

8 (no connection)

Figure 4. Model 2173 10/100Base-T RJ-45 Connector Pinout.

3.3 CONNECTING POWER

The Interconnecting cables shall be acceptable for

external use and shall be rated for the proper applica-

tion with respect to voltage, current, anticipated tem-

CAUTION perature, flammability, and mechanical serviceability.

The Model 2173 does not have a power switch, so it powers up as soon as it is plugged in.

An external AC or DC power supply is available separately. This connec- tion is made via the barrel jack on the rear panel of the Model 2173. No configuration is necessary for the power supply (See Appendix B for domestic and international power supply and cord options).

DC power (supplied via the power supply jack to the 2173) must meet the following requirements; DC power supplied must be regulated +5VDC ±5%, 1.0A minimum. Center pin is +5V. The barrel type plug has a 2.5/5.5/10mm I.D./O.D./Shaft Length dimensions.

4.0 CONFIGURATION

The Model 2173 has four DIP switches (S1) for configuring the unit for a wide variety of applications. This section describes switch locations and explains the different configurations.

4.1 CONFIGURING THE HARDWARE DIP SWITCHES

Using a small flat-tip screwdriver, remove the protective cover located on the underside of the Model 2173 (see Figure 5).

12

Image 12
Contents User Manual Contents Distance Chart, Based on 24 AWG 0.5 MM Warranty Information Regulatory InformationRadio and TV Interference FCC Part Service CE Declaration of ConformityAuthorized European Representative Safety When Working with Electricity Page Features General InformationDescription Installation Typical applicationConnecting the TWISTED-PAIR Line Interface ModelConnecting the 10/100BASE-T Ethernet Interface Model 2173 RJ-45 twisted pair line interfaceConnecting Power ConfigurationConfiguring the Hardware DIP Switches Front Configuring DIP Switch S1 Power UPCPE OFFFront Panel LED Status Monitors LEDLED Status Indicators Power SupplyTemperature Range DimensionsAppendix B Base ModelsAppendix C 10/100BASE-T InterfaceCopperlink Interface Appendix D Copyright Patton Electronics Company All Rights Reserved

2173 specifications

The Patton Electronic 2173 is a versatile and robust digital communications device designed to enable seamless connectivity in a variety of networking environments. Known for its reliability and advanced feature set, the 2173 offers businesses a solution that enhances both performance and flexibility.

One of the standout features of the Patton 2173 is its support for multiple protocols. It is capable of functioning as a VoIP gateway, enabling voice over Internet Protocol services, while also supporting legacy analog phone systems. This dual capability allows organizations to bridge the gap between traditional telephony and modern IP-based communications, ensuring that businesses can migrate to new technologies without losing their existing investments.

In terms of connectivity, the Patton 2173 offers various interfaces, including FXS (Foreign Exchange Station) ports and FXO (Foreign Exchange Office) ports, which facilitate the integration of both analog and digital phones. This flexibility is particularly valuable for small to medium-sized businesses looking to optimize their communication infrastructure without extensive overhauls.

The device also incorporates advanced signal processing technology, which enhances voice quality by minimizing latency and jitter. This is crucial in ensuring clear and uninterrupted communication, especially in environments where high call traffic is managed. Moreover, the Patton 2173 supports echo cancellation and noise reduction features, further elevating voice clarity during calls.

User-friendliness is another integral aspect of the Patton 2173. With a web-based graphical interface, configuration and management are straightforward, even for those with limited technical expertise. This ease of use extends to its monitoring capabilities, where administrators can keep track of call performance and system health via an intuitive dashboard.

Security is a top concern in today’s digital communication landscape, and the Patton 2173 does not disappoint. It offers various security features, such as SRTP (Secure Real-Time Transport Protocol) and TLS (Transport Layer Security) encryption to safeguard voice data against potential threats.

The build quality of the Patton 2173 is industrial-grade, ensuring its longevity even in demanding environments. It is designed to support a variety of operating temperatures, making it suitable for deployment in diverse settings.

In summary, the Patton Electronic 2173 is a powerful communication device that combines flexibility, advanced technology, and user-friendly features, making it an ideal choice for organizations looking to enhance their voice communication systems while embracing modern networking solutions.