TP-Link TL-WR740N manual Local Management

Page 64

TL-WR740N

Wireless Lite N Router

¾DoS protection - Denial of Service protection. Check the Enable or Disable button to enable or disable the DoS protection function. Only when it is enabled, will the flood filters be enabled.

) Note:

Dos Protection will take effect only when the Traffic Statistics in “System Tool → Traffic Statistics” is enabled.

¾Enable ICMP-FLOOD Attack Filtering - Enable or Disable the ICMP-FLOOD Attack Filtering.

¾ICMP-FLOOD Packets Threshold (5~3600) - The default value is 50. Enter a value between 5 ~ 3600. When the current ICMP-FLOOD Packets number is beyond the set value, the Router will startup the blocking function immediately.

¾Enable UDP-FLOOD Filtering - Enable or Disable the UDP-FLOOD Filtering.

¾UDP-FLOOD Packets Threshold (5~3600) - The default value is 500. Enter a value between 5 ~ 3600. When the current UPD-FLOOD Packets number is beyond the set value, the Router will startup the blocking function immediately.

¾Enable TCP-SYN-FLOOD Attack Filtering - Enable or Disable the TCP-SYN-FLOOD Attack Filtering.

¾TCP-SYN-FLOOD Packets Threshold (5~3600) - The default value is 50. Enter a value between 5 ~ 3600. When the current TCP-SYN-FLOOD Packets numbers is beyond the set value, the Router will startup the blocking function immediately.

¾Ignore Ping Packet From WAN Port - Enable or Disable Ignore Ping Packet From WAN Port. The default setting is disabled. If enabled, the ping packet from the Internet cannot access the Router.

¾Forbid Ping Packet From LAN Port - Enable or Disable Forbid Ping Packet From LAN Port. The default setting is disabled. If enabled, the ping packet from LAN cannot access the Router. This function can be used to defend against some viruses.

Click the Save button to save the settings.

Click the Blocked DoS Host List button to display the DoS host table by blocking.

4.9.3Local Management

Choose menu “Security → Local Management”, you can configure the management rule in the screen as shown in Figure 4-40.The management feature allows you to deny computers in LAN from accessing the Router.

- 57 -

Image 64

Contents TL-WR740N Copyright & Trademarks FCC Statement FCC RF Radiation Exposure Statement Country Restriction Reason/remarkProduct Description Wireless Lite N Router Zhao Jianjun Director of International BusinessContents Dhcp 100 Package Contents Flexible Access Control Simple InstallationOverview of the Router Incredible SpeedMain Features ConventionsPanel Layout Front PanelName Status Indication Wlan¾ RESET： Rear PanelConnecting the Router Installation Environment RequirementsSystem Requirements TL-WR740N Quick Installation Guide TCP/IP ConfigurationSuccess result of Ping command Please check the connection following these stepsQuick Installation Guide Login WindowsQuick Setup Quick Setup Static IP Quick Setup Wireless 10 Quick Setup Finish Login StatusRouter Status QSS Quick SetupBy PBC Method One Method TwoMethod Three Add a New Device II. By PIN NextTL-WR740N Network 1 LAN2 WAN LANTL-WR740N TL-WR740N WAN PPPoE TL-WR740N 10 PPPoE Advanced Settings NSW / ACT nsw.bigpond.net.au TL-WR740N 12 WAN L2TP TL-WR740N 13 Pptp Settings MAC Clone Wireless Wireless Settings16 Wireless Settings Wireless Security 17 Wireless Security Encryption You can select either Automatic, or Tkip or AES 19 WPA/WPA2Wireless MAC Filtering TL-WR740NWireless Lite N Router21 Wireless MAC Filtering To modify or delete an existing entry Wireless Advanced Wireless Statistics 24 Wireless StatisticsDhcp Settings DhcpDhcp Clients List 27 Dhcp Clients ListAddress Reservation To Reserve an IP addressForwarding Virtual ServersTo setup a virtual server entry 32 Add or Modify a Virtual Server EntryPort Triggering To add a new rule, follow the steps below 34 Add or Modify a Port Triggering EntryUPnP 3 DMZTo assign a computer or server to be a DMZ server Security Basic SecurityAs shown in Figure Advanced Security Local Management Remote Management 40 Local ManagementParental Control 41 Remote Management42 Parental Control Settings To add a new entry, please follow the steps below43 Add or Modify Parental Control Entry 11Access Control Rule46 Access Control Rule Management To add a new rule, please follow the steps below47 Add or Modify Internet Access Control Entry 48 Host Settings Host49 Add or Modify a Host Entry 51 Target Settings Target52 Add or Modify an Access Target Entry 54 Schedule Settings Schedule55 Advanced Schedule Settings To add a new schedule, follow the steps belowStatic Routing To add static routing entries, follow the steps belowControl Settings Bandwidth Control59 Bandwidth Control Settings Rules List14IP& MAC Bing Setting Binding SettingsTo add IP & MAC Binding entries, follow the steps below To find an existing entry, follow the steps belowARP List 65 Find IP & MAC Binding EntryDynamic DNS Comexe.cn DdnsTo set up for DDNS, follow these instructions Dyndns.org Ddns68 Dyndns.org Ddns Settings System Tools 70 The System Tools menuTo configure the system manually Time SettingsTo configure the system automatically Diagnostic Firmware Upgrade 73 Diagnostic ResultsFactory Defaults 75 Restore Factory DefaultBackup & Restore RebootPassword System log79 System Log TL-WR740N Statistics 81 StatisticsStatistics Table IP/MAC Address PacketsTotal BytesAppendix a FAQ Figure A-3 MAC Clone Want to use NetMeeting, what do I need to do?Figure A-5 Add or Modify a Virtual server Entry Figure A-7 Basic Security Want to build a WEB Server on the LAN, what should I do?Wireless stations cannot connect to the Router Figure A-9 Virtual ServersAppendix B Configuring the PC Configure TCP/IP componentShown in the Figure below ¾ Setting IP address manually Now General WirelessEnvironmental and Physical Appendix D Glossary 102