TP-Link TL-WR941ND FCC RF Radiation Exposure Statement, CE Mark Warning, National restrictions

Page 3

FCC RF Radiation Exposure Statement

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

CE Mark Warning

This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

National restrictions

This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:

	Country	Restriction	Reason/remark

	Bulgaria	None	General authorization required for outdoor use and
	Bulgaria	None	public service
			public service

Outdoor use limited to 10

FrancemW e.i.r.p. within the band 2454-2483.5 MHz

Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012

	Italy	None	If used outside of own premises, general authorization is
	Italy	None	required
			required

	Luxembourg	None	General authorization required for network and service
	Luxembourg	None	supply(not for spectrum)
			supply(not for spectrum)

	Norway	Implemented	This subsection does not apply for the geographical area
	Norway	Implemented	within a radius of 20 km from the centre of Ny-Ålesund
			within a radius of 20 km from the centre of Ny-Ålesund

	Russian Federation	None	Only for indoor applications

Note: Please don’t use the product outdoors in France.

II

Image 3

Contents Rev 1.1.0 TL-WR941ND Wireless N RouterFCC STATEMENT COPYRIGHT & TRADEMARKSCountry FCC RF Radiation Exposure StatementCE Mark Warning National restrictionsIndustry Canada Statement Korea Warning StatementsNCC Notice Page EN 550241998+A12001+A22003 EN 61000-3-22006+A12009+A22009 EN DECLARATION OF CONFORMITYETSI EN 300 328 ETSI EN 301 489-1 V1.8.12008& ETSI EN 301 489-17 EN 550222006 +A12007CONTENTS Package ContentsChapter DHCP 4.15.2 TL-WR941ND Wireless N Router Package Contents1.1 Overview of the Router Flexible Access ControlSimple Installation Chapter 1.Introduction1.3 Main Features Status 1.4 Panel Layout1.4.1 The Front Panel Name1.4.2 The Rear Panel ¾ RESET2.1 System Requirements Chapter 2.Connecting the Router2.2 Installation Environment Requirements 2.3 Connecting the RouterFigure 2-1 Hardware Installation of the TL-WR941ND Wireless N Router 3.1 TCP/IP Configuration Chapter 3.Quick Installation Guide1. Is the connection between your PC and the Router correct? Please check the connection following these stepsFigure 3-1 Success result of Ping command Figure 3-2 Failure result of Ping command3.2 Quick Installation Guide Figure 3-6 Choose WAN Connection Type Figure 3-5 Quick SetupFigure 3-8 Quick Setup - MAC Clone Figure 3-7 Quick Setup - PPPoEFigure 3-10 Quick Setup - Static IP Figure 3-9 Quick Setup - MAC CloneNote Dialog ¾ WPA/WPA2-Personal - Select WPA based on pre-shared passphrase 4.6 WirelessFigure 3-13 Quick Setup - Finish Chapter 4.Configuring the Router 4.1 Login4.2 Status Figure 4-1 Router Status 4.3 Quick SetupPlease refer to 3.2 Quick Installation Guide 4.4 QSSMethod One I. By PBCMethod Two The QSS Configuration Screen of Wireless Adapter Method ThreeTL-WR941ND Wireless N Router II. By PIN Method Two Enter the PIN from my Router 4.5 Network 4.5.1 WANadded to the network Figure 4-5 WAN - Dynamic IP Figure 4-6 WAN - Static IP Figure 4-7 WAN - PPPoE Figure 4-8 PPPoE Advanced Settings NSW / ACT - nsw.bigpond.net.au QLD - qld.bigpond.net.au Figure 4-10 L2TP Settings Figure 4-11 PPTP Settings z Static IP - Connections which use static IP address assignment z Dynamic IP - Connections which use dynamic IP address assignmentFigure 4-13 MAC Address Clone 4.5.2 LAN4.5.3 MAC Clone Figure 4-12 LAN4.6 Wireless 4.6.1 Wireless SettingsOnly the PC on your LAN can use the MAC Address Clone function Figure 4-15 Wireless Settings ¾ Mode - Select the desired mode. The default setting is 11bgn mixed 4.6.2 Wireless Security ¾ WPA /WPA2 - Enterprise - It’s based on Radius Server Encryption - You can select either Automatic, or TKIP or AES Figure 4-20 Wireless MAC address Filtering 4.6.3 Wireless MAC Filtering4. Click the Save button to save this entry to access for Filtering Rules 4.6.4 Wireless Advanced4.6.5 Wireless Statistics 4.7.1 DHCP Settings 4.7 DHCPThis page will be refreshed automatically every 5 seconds ¾ Default Domain - Optional. Input the domain name of your network 4.7.3 Address Reservation 4.7.2 DHCP Clients List4.8 Forwarding To Reserve IP addressesTo modify or delete an existing entry 4.8.1 Virtual Servers To set up a virtual server entryFigure 4-31 Add or Modify a Virtual Server Entry 4.8.2 Port TriggeringTo add a new rule, follow the steps below 3. Incoming Port Range cannot overlap each other 4.8.3 DMZTo assign a computer or server to be a DMZ server 4.8.4 UPnP4.9.1 Basic Security 4.9 Securityz z z Figure 4-37 Basic Security4.9.2 Advanced Security 4.9.3 Local Management Figure 4-39 Local Management 4.9.4 Remote ManagementFigure 4-40 Remote Management 4.10Parental ControlTo add a new entry, please follow the steps below 7. Click the Save button 4.11.1 Rule 4.11Access ControlFigure 4-45 Access Control Rule Management To add a new rule, please follow the steps belowFigure 4-46 Add or Modify Internet Access Control Entry Figure 4-47 Host Settings 4.11.2 HostFigure 4-49 Add or Modify a Host Entry Figure 4-48 Add or Modify a Host EntryFigure 4-50 Target Settings 4.11.3 TargetFigure 4-52 Add or Modify an Access Target Entry Figure 4-51 Add or Modify an Access Target EntryTo add a new schedule, follow the steps below 4.11.4 Schedule4.12 Advanced Routing Figure 4-54 Advanced Schedule SettingsFigure 4-55 Advanced Routing Other configurations for the entries 4.12.1 Static Routing ListTo add static routing entries 4.12.2 System Routing Table 4.13Bandwidth Control4.13.2 Rules List 4.13.1 Control Settings4.14IP & MAC Binding Setting 4.14.1 Binding SettingTo add/modify a Bandwidth Control rule, follow the steps below Figure 4-64 Binding Setting To add IP & MAC Binding entries, follow the steps belowTo modify or delete an existing entry, follow the steps below To find an existing entry, follow the steps below4.14.2 ARP List Figure 4-66 Find IP & MAC Binding EntryFigure 4-67 ARP List 4.15.1 Comexe.cn DDNS 4.15Dynamic DNS4.15.2 Dyndns.org DDNS To set up for DDNS, follow these instructionsFigure 4-69 Dyndns.org DDNS Settings 4.15.3 No-ip.com DDNS4.16System Tools Figure 4-70 No-ip.com DDNS SettingsFigure 4-71 The System Tools menu To set time manually 4.16.1 Time Settings2. The time will be lost if the router is turned off 4.16.2 DiagnosticTo set time automatically To set Daylight SavingFigure 4-73 Diagnostic Tools To upgrade the Routers firmware, follow these instructions below 4.16.3 Firmware Upgrade4.16.4 Factory Defaults 4.16.5 Backup & Restore4. The Router will reboot after the upgrading has been finished 4.16.6 Reboot 4.16.8 System Log 4.16.7 PasswordFigure 4-80 System Log Figure 4-81 Mail Account Settings Figure 4-82 Statistics 4.16.9 StatisticsWireless N Router TL-WR941NDStatistics Table 1. How do I configure the Router to access Internet by ADSL users? Appendix A FAQ3. I want to use Netmeeting, what do I need to do? Figure A-3 MAC CloneFigure A-4 Virtual Servers Figure A-6 DMZ Figure A-5 Add or Modify a Virtual server Entry4. I want to build a WEB Server on the LAN, what should I do? field of the Web browser 5. The wireless stations cannot connect to the Router1. Install TCP/IP component Appendix B Configuring the PCsFigure B-2 ¾ Setting IP address automaticallyNow you have two ways to configure the TCP/IP protocol below shown in the Figure belowFigure B-3 ¾ Setting IP address manuallyFigure B-4 Environmental and Physical Appendix C SpecificationsWireless GeneralAppendix D Glossary identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name

Related manuals

Manual 76 pages 42.16 Kb